Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4   Go Down

Author Topic: Melodeon tuning tools  (Read 13550 times)

0 Members and 1 Guest are viewing this topic.

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Melodeon tuning tools
« Reply #40 on: January 15, 2014, 07:53:46 PM »

Had a spare 10 mins in the workshop today.

German Lifter Video

How thick is the metal used to make the lifter?

george
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #41 on: January 16, 2014, 12:13:20 AM »

The reed does indeed bend, but that is what they do for a living. The ability to use this type of reed lifter is an art which I have yet to master on anything but the larger reeds.

It seems strange that you are suddenly so deft at this that you are now posting videos on the subject. Would you care to share with the rest of us the inspirational moment when all became so clear?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Melodeon tuning tools
« Reply #42 on: January 16, 2014, 01:26:31 AM »

Had a spare 10 mins in the workshop today.

German Lifter Video

Just out of interest Lester have you tried pulling the reed through without using any leverage? The end of your reed lifter is even more mangled than mine!  :D

I think this question is the key to your difficulty with this type of lifter.  There is really no levering at all.  If you do try to lever the reed it will bend the fragile lifter.  The lifter binds itself between the reed tip and the reed frame and that allows you to pull the reed through to the other side.  During that process there is only tension on the lifter...no levering.  When the reed pops through then you can lever the lifter under it for support.  That's my take on it anyway.  Hope that helps.
Logged

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Melodeon tuning tools
« Reply #43 on: January 16, 2014, 12:43:02 PM »

That bent reed looks dodgy! I've got a lifter made out of strong wire with a curve at the end, like a hockey stick. Its easy to slip it down the gap at the end of the reed, turn it 90 degrees, and lift he reed. One its lifted I put a thin shim under to support it. Then reverse the process once its been filed/scratched.
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #44 on: January 16, 2014, 01:36:02 PM »

How thick is the metal used to make the lifter?

george

I have three Hohner lifters, a very fine one that is 0.3mm thick and only works with the tiniest of reeds, the one I use most is 0.5mm thick, both of these end in a wickedly sharp point. The third seems more like a reed support for tuning as it is 0.8 thick and 5mm wide at the tip and I've never encountered a bass reed big enough use it on! I'll post pictures later.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #45 on: January 16, 2014, 03:25:39 PM »



Left to right:

0.3mm reed lifter - 0.5mm reed lifter - 0.8mm reed support - 0.3mm spring steel reed pinger - 1mm scratcher - 1.5mm scratcher - 2.4mm scratcher - diamond spatula file - old dental tool - set of feeler gauges.

The 1mm scratcher is in a Hohner handle and the tip is a snapped off cobalt drill bit. The 1.5mm scratcher handle I made myself by drilling a piece of 3mm steel rod in a lathe. The reed pinger and the 2.4mm scratcher came from Watkins (WEM).
« Last Edit: January 16, 2014, 06:19:11 PM by tallship »
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Melodeon tuning tools
« Reply #46 on: January 16, 2014, 03:29:36 PM »

I've made reed lifters from thin brass and they work very well. The movement is just up and down, no levering needed. I do worry about it increasing the gap at the top of the reed, but it doesn't seem to.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Melodeon tuning tools
« Reply #47 on: January 16, 2014, 03:56:30 PM »

How thick is the metal used to make the lifter?

george

After investing in a new battery for my vernier gauge it measures as 0.3mm

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Melodeon tuning tools
« Reply #48 on: January 16, 2014, 05:46:08 PM »

I have used both the German and Italian style reed lifter....one item mentioned in the video especially caught my attention: the occasional requirement for a "third hand". Could be useful in many situations  (:)
Logged

Tony M

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Melodeon tuning tools
« Reply #49 on: February 05, 2014, 07:04:20 PM »

Further to my hunt for spare reeds (see the buy and sell section), can I offer a note of caution:

I'm fairly sure I know, now, what I did to the reeds:

These German style lifters looked really useful, so I made a couple, trying them out on the bigger reeds (I had my Trichord open on the bench at the time, having finalised the tuning on a couple of notes). 

I made the lifters from sections of a hacksaw blade, suitably ground down and bent - hard, but could be ground very thin without bending or breaking.  They worked a treat, lifting the reeds with barely a click.  Brass might have been better, being softer - but lacks the stiffness (and I didn't have any!).

I was pleased, so I made another, with a very fine tip thinking it would suit the smallest reeds - and this, with hindsight, was a mistake.

It seemed OK, but I now know I damaged (several!) reeds when I tried it (and didn't spot this at the time).

I'm not sure whether an experienced user could get away with one of these on the smallest reeds, but I won't be repeating the experiment - the reed tips are very fine, and damage is easily caused, so it's back to the slow approach for me.

Cheers,

(still embarrassed!)   :-[

Tony M
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Melodeon tuning tools
« Reply #50 on: February 05, 2014, 08:17:14 PM »

I can quite happily lift the highest reeds on a D/G (F#6) using a 0.33mm brass lifter. In fact I find the high ones easier to lift. What I did was to practice on an old accordion reed block I had laying around.

Tony M

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Melodeon tuning tools
« Reply #51 on: February 06, 2014, 06:04:33 PM »

Hi, Lester.

I can quite happily lift the highest reeds on a D/G (F#6) using a 0.33mm brass lifter. In fact I find the high ones easier to lift. What I did was to practice on an old accordion reed block I had laying around.

Duly noted, and thanks for the advice:  I think the bits I've put in bold are the key elements of that - I really should have known better than to try it out on a good box.  My sense of "What's the worst that can happen" failed me!

I might try again - on something spare / redundant, and with due care and attention.  That style of lifter is very convenient.

Cheers,

Tony M
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Melodeon tuning tools
« Reply #52 on: March 12, 2014, 11:05:07 AM »

Left to right:
0.3mm reed lifter - 0.5mm reed lifter - 0.8mm reed support - 0.3mm spring steel reed pinger - 1mm scratcher - 1.5mm scratcher - 2.4mm scratcher - diamond spatula file - old dental tool - set of feeler gauges.

The 1mm scratcher is in a Hohner handle and the tip is a snapped off cobalt drill bit. The 1.5mm scratcher handle I made myself by drilling a piece of 3mm steel rod in a lathe. The reed pinger and the 2.4mm scratcher came from Watkins (WEM).

In Thierry Benetoux's book 'Sounding out the accordion' he describes (on pp 86 of my copy) how to make a 'scraper', which I assume is a scratcher. He writes 'Take a 20cm rod...', and shows how to harden it, but does not say what this rod is made of. In the list above, the scratcher is made from a busted drill bit, which I assume is already hardened.
So:
1) what metal should be used to make a scraper/scratcher?
2) is a ground down drill bit sufficient and not in need of hardening?

 

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: Melodeon tuning tools
« Reply #53 on: March 12, 2014, 11:51:04 AM »

I have tried all the various lifters described in the Forum and elsewhere over the years, and all work reasonably well if used with care. I now make them out of bronze sheet of various thicknesses, which is easy to cut and shape, yet not as soft and bendy as brass. The initial outlay for a sheet about 6 inches x 12 inches is not inconsiderable, but I have enough for several dozen lifters.

I also have a couple of super-strong neodymium magnets, rectangular in shape (about 20mm x 5mm x 1.5mm thick). These are glued to a wooden handle, and I find they fit readily into even the smallest reed slot. On larger reeds, they will lift a reed completely, and on smaller, stiffer ones, they help open a space for the bronze lifter to gain access. In other words, they lessen the need to poke, twist and pry the reeds. What the long term effect of magnetism may be, I have absolutely no idea.

On the business of making scratchers out of drill bits, grinding them at high speed on a wheel can make them overheat and lose temper, in which case they will need re-tempering to be any good. The finest scratcher I've got is a smart-looking stainless, brass and wood pen-shaped instrument with a diamond tip, which I think is for scribing fibre optic cables. I got it (used) off eBay for about £5 as an experiment, and I'm glad I did.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Melodeon tuning tools
« Reply #54 on: March 12, 2014, 01:04:18 PM »

What the long term effect of magnetism may be, I have absolutely no idea.
A couple of things come to mind...

A magnetised steel reed tongue oscillating in the slot of an aluminium reed plate will generate eddy currents in the aluminium which will exert a counter force which might tend to damp the reed tongue vibrations. This could be useful in reducing the volume of loud boxes!

On the other hand, with a bit of electronic wizardry, it might be possible to harness the eddy currents, amplify them and play them through a PA sound system of some sort. No microphones required, which would eliminate any feedback problems at gigs.

Mind you, pigs might fly...   
>:E
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Melodeon tuning tools
« Reply #55 on: March 12, 2014, 01:56:41 PM »

A quick pass over with a degaussing coil and the box would suddenly fall silent  >:E

I think the idea of a magnetic pickup per reed has been discussed around here before somewhere.
It would almost certainly sound horrid, and you'd get an audible decay after the note was supposed to finish.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Melodeon tuning tools
« Reply #56 on: March 12, 2014, 02:13:20 PM »

I've still got access to a couple of 3 Tesla (30,000 Gauss) magnets, should anyone want to try this :o

   Mind you .. you might never get it out again >:E
Logged
  _       _    _      _ 

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #57 on: March 12, 2014, 07:09:30 PM »

On the business of making scratchers out of drill bits, grinding them at high speed on a wheel can make them overheat and lose temper, in which case they will need re-tempering to be any good.

Grinding on a high speed wheel? Place drill bit in a vice with the twist end pointing upward and give it a sharp sideways tap with a hammer, the drill is so hard it snaps cleanly. Fit the straight shank of the drill into a scratcher handle or a pin vice and dress the broken end flat and square on a diamond file and it's good to go.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Melodeon tuning tools
« Reply #58 on: March 12, 2014, 08:19:41 PM »

Made a degaussing coil out of an old relay coil and a small mains transformer. Worked fine on tape heads (intended use) and screwdrivers (serendipitious). Never though of keeping it for reeds.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #59 on: March 12, 2014, 10:35:50 PM »

So:
1) what metal should be used to make a scraper/scratcher?
2) is a ground down drill bit sufficient and not in need of hardening?

Anything harder than the reed material will abrade it but something significantly harder will do so more quickly and with less effort. Cobalt drills eat their way through the hardest of stainless steels, albeit with cutting paste to keep things lubricated and cool. Faced with blued spring steel it's no contest, the sharp cutting edge of a cobalt drill will scratch/scrape a fine, controlled line with ease. See my post above for an explanation why re-tempering of the drill bit isn't needed.

Prestidigitator's diamond tipped tool will of course achieve exactly the same thing with significantly less effort and therefore by definition, much greater control.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)
Pages: 1 2 [3] 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal