Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner 499/31/16 GCF  (Read 1577 times)

0 Members and 1 Guest are viewing this topic.

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Hohner 499/31/16 GCF
« on: January 11, 2014, 09:02:04 PM »

Firstly I am looking for any history about this one. I bought from eBay (http://forum.melodeon.net/index.php/topic,13899.msg171017.html#msg171017)

It is reasonably good condition. I have some questions about the reeds. I have added some images of one of the reed blocks. To keep with the original installation as much as possible I would like to use the same construction method of reed attachment rather than wax them in.

My questions:

The bent nail/staple arrangement, can I reuse and is it best to twist them so I can remove the reeds for re-valving.
What is the leather that is used to seal the reeds against the reed block?
To keep with original build I would like to use leather for the valves, am I right?

I have some other questions later about the exterior, but I want to have the reeds right first.

Stephen
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner 499/31/16 GCF
« Reply #1 on: January 11, 2014, 09:12:57 PM »

Quote
The bent nail/staple arrangement, can I reuse and is it best to twist them so I can remove the reeds for re-valving.
What is the leather that is used to seal the reeds against the reed block?
To keep with original build I would like to use leather for the valves, am I right?

I would reuse the screws in their existing holes but if I used the nails I would knock them into a new position. To be honest I would try without the nails.

To replace the leather I would use olivisc (sp??) available from Charlie

It's up to you what you use for valves. Again Charlie is your man

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Hohner 499/31/16 GCF
« Reply #2 on: January 15, 2014, 01:01:24 AM »

Wow, the nap on the gasket lacks the characteristic "air stains" next to the holes and looks unused. Nice box, there! Good luck with the project.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Hohner 499/31/16 GCF
« Reply #3 on: January 15, 2014, 05:46:28 AM »

Same setup on my old Hohner 3 row. Check the base of the reed blocks with a straight-edge...if slightly bowed, level them. Lightly brush the nap of the gasket material with a soft child's toothbrush. The screws and bent nails are a good system if un-tampered-with. To remove/replace reed, gently twist nail 90 degrees, don't pull it out. If screws have not been abused, or stripped in the holes, they will work fine. Be sure to tighten them very carefully so they are just *snug*.
   My old Hohner has the original nails, screws, and leathers (save one or two)that were originally on the treble side. I found that the leather was of superior quality, and was still quite pliable. I was able to remove all the reeds for cleaning and re-pitching to A440 with leathers intact, and using the home-made tool shown in the "Talking Reeds" website, was able to comb them back to relative flatness. I have played it steadily for 10 or so years, and no valve problems, and still great compression. I did replace the leathers on the basses, though...they were just to big to remain straight and provide a good seal. I used Italian leather with booster springs. I'm not a big fan of the plastic valves, although they seem to seal better, but I do not like the noise they make opening and closing, and sometimes they will even produce a vibration in sympathy with the reed which can be quite unpleasant. I hope your old Hohner gives as much enjoyment as I have had from mine! (:)
Logged

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Hohner 499/31/16 GCF
« Reply #4 on: March 12, 2014, 08:36:05 PM »

Great advice for revalving my Geipel, the reeds are fastened on in the same way. Ta.
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal