Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Melodeon Maintenance Day 23rd March 2014  (Read 4898 times)

0 Members and 1 Guest are viewing this topic.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Melodeon Maintenance Day 23rd March 2014
« Reply #20 on: March 25, 2014, 05:52:29 PM »


The steel pallet strapping is used for making general purpose flat thingies, used for pinging reeds, supporting reeds when filing, scraping wax and many other fettlings.

The GP flat thingies can also be made from empty baked beans etc., cans. Ensure your can is steel, not aluminium which is a bit too soft. If in doubt, test with a magnet!

Cut both ends off the can with a tin opener. Using tin-snips or even hefty kitchen scissors, cut the resulting cylinder vertically and flatten out into a sheet. Then, from the non-corrugated portions of the can, cut strips about 4 inches long by 1/2 inch wide. File off any sharp burrs along the strip edges. Flatten the strip as much as possible using a rolling pin. Finally, file down the 1/2 inch or so on each end face, thinning it to a shallow wedge and a fairly sharp edge on the tip.

You can cut several GP thingies from a single can, and make them different sizes and shapes (parallel-sided, tapered, etc.)
 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Melodeon Maintenance Day 23rd March 2014
« Reply #21 on: March 26, 2014, 06:57:41 AM »

- What tape to use to blank off reed banks when tuning? Masking tape?
If you want to blank off a whole bank of reeds on a reed plate, a strip of plain paper covering up the air vents will do. It's held in place by the pressure of the reed block clamps. It doesn't need to be sticky.

On the other hand, it can sometimes be a bit fiddly keeping the paper strip in place while you replace the reed block. I often use "Post-It Tape on a roll". It's just like the sticky edge of ordinary post-it notes but a whole roll of it (25m) and sticky across the whole width. It sticks like a post-it note and comes away easily and cleanly with no sticky residue.

With scissors, I cut a strip in half lengthways and it is just right for blanking off one half of a reed plate. When I'm finished with it, I peel it off and stick it up on the wall of my workshop ready for use another time. It can be used several times over.

Small slivers of the same tape can be used for blanking off individual tongues and slots - useful when tuning basses and chords especially. It avoids repeatedly removing the reed block.

Very useful stuff!

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Melodeon Maintenance Day 23rd March 2014
« Reply #22 on: March 27, 2014, 12:57:18 PM »

It was a most enjoyable day thanks to all those that attended, hope to see you again soon. And a special thanks to Katie for organising it all.

Martyn
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal