Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4   Go Down

Author Topic: Hide Glue Pot for Reed Wax?  (Read 12429 times)

0 Members and 1 Guest are viewing this topic.

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hide Glue Pot for Reed Wax?
« Reply #40 on: January 12, 2016, 08:53:45 AM »

I looked up bees wax as melting 80 to 85c so that should give the bottom end of the range.

On glues, to clarify - bookbinder's PVA can be removed with water after it's dried?

Bookbinders PVA remains flexible when dry. Water soluble  PVA  is a fairly recent  innovation.
So be careful, the unsoluble is still the most common.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hide Glue Pot for Reed Wax?
« Reply #41 on: January 12, 2016, 09:14:36 AM »

method, in which case the need to remove this from the work area to avoid breathing in is very important.

Quote
but you only have the one pair of lungs, on which bellows tape is little use  ;)

Just to emphasise this, rosin fumes are a well known source of industrial asthma and people who work near it are required to have regular lung function checks. Once the condition is established, it doesn't get better.
So good ventilation is essential, and avoid inhaling fumes.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Henry Piper

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 368
Re: Hide Glue Pot for Reed Wax?
« Reply #42 on: January 12, 2016, 10:17:38 AM »

Just ran some wax & turps polish on Sunday using a recently revived kitchen kettle which had died for domestic purposes and operating via my trusty 'Reedwaxers Friend' (a 3KW mains variable PSU) all went well other than I need to educate the kill thermostat to operate just a little warmer as it cut out a shade low.  Next time I run some reed wax I'll try to establish a temperature range and post to one of the previous reedwax threads.

Re Henry's post, I'd not seen any of the tried and trusted reedwax recipes using turps to dissolve the resin, knowing how relatively little softens wax for polish purposes, this may well fume off if using hot iron method, in which case the need to remove this from the work area to avoid breathing in is very important. If not all evaporates this may leave the wax softer / wetter than a trad recipe, so the longer term life in your experimental box will be interesting.

Of these two aspects, there are still thousands of unburned Saxony boxes on which to experiment but you only have the one pair of lungs, on which bellows tape is little use  ;)
Just to clarify:-  in my original post I said "many" of the recipes included Turps, on reflection it would perhaps be more accurate to say "some". I dissolved the rosin in the minimum amount of turps needed to completely dissolve it after about 24 hours or so, I am aware of the risks of inhaling rosin fumes so whilst adding and mixing the turps/rosin mixture to the molten wax kept the  temperature as low as possible whilst keeping it liquid, to minimise fuming as far as possible, and worked in a ventilated area. the resulting wax when first set WAS wetter and softer than pure beeswax, but after a couple of days exposure to the air had hardened considerably , and was much like commercial wax that I have seen in the past.
 As a test I waxed 1/2 dozen unwanted reeds into an old klingenthal box that I use for experiments, the wax has good adhesive qualities, and flows nicely with a quick setting time, and appears to do its job in securing the reeds to the block, they have been in place for several weeks now, and appear to be still firmly in position.
I would add that I do not consider myself a "Repairer" as such, just someone who enjoys doing maintenance on my own instruments, and is interested in the techniques involved, in view of the work involved in producing this wax, I would probably buy commercially made wax, for future repairs, but it has been an interesting experiment.
Logged
From Ottery St Mary Devon. Currently Playing Dino Baffetti BP2 in D/G, Hohner Student 1 P.A conversion  in D/G,  Hohner 3515 Pre-Pokerwork in A/D,   2 row "Beaver Brand" in Bb/Eb, Hohner Pre- Erica in G/C .  Single row permanent 4 voice, 4 bass in C from old Hohner single row and bits of a cheap Cajun box !!,

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Hide Glue Pot for Reed Wax?
« Reply #43 on: January 13, 2016, 12:37:16 AM »

Fair comment Henry, the wax making shouldn't entail enough heat to get much in the way of fumes, it was the actual reedwaxing, if using an iron, where the proportion left on the bit may fume with the turps fraction going first.
As long as you are aware fine, but for every poster there are probably more lurkers who read this stuff and may tinker without due care..........

I shall have to experiment with using Turps to pre soften the resin and see how it goes - the finer powder seems to curdle for some reason.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Barlow

  • Bad player, good talker apparently
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 111
  • Castagnari Lilly B/C Erica D/G
Re: Hide Glue Pot for Reed Wax?
« Reply #46 on: March 09, 2018, 07:07:19 PM »

Serious question, not wanting to sound controversial but what might be wrong about using a high modulus sealant in place of beeswax/resin
Logged
. . .

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hide Glue Pot for Reed Wax?
« Reply #47 on: March 09, 2018, 07:30:16 PM »

Serious question, not wanting to sound controversial but what might be wrong about using a high modulus sealant in place of beeswax/resin
It's been covered on this forum before. Use the Google Search facility (blue menu strip at the top of each page)to find relevant threads.

The basic answer is the reversibility and ease of removal of wax. Reed plates do occasionally need to be removed as part of a repair, restoration or tuning process.

I do assure you that having had to remove some reed plates which had been fixed on with (a) impact adhesive and (b) silicone bathroom sealant, and clean up the resulting MESS, I could quite happily stuff sealant down the offender's throat. Don't ever be tempted to try using it.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hide Glue Pot for Reed Wax?
« Reply #48 on: March 09, 2018, 08:44:45 PM »

Serious question, not wanting to sound controversial but what might be wrong about using a high modulus sealant in place of beeswax/resin

There is a major risk that the next guy who has to work on the box will seek you out beat you to death.  (:)

I have had to do this work and it is horrendous.

Barlow

  • Bad player, good talker apparently
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 111
  • Castagnari Lilly B/C Erica D/G
Re: Hide Glue Pot for Reed Wax?
« Reply #49 on: March 09, 2018, 08:56:22 PM »

Thank you for the unequivocal replies!

I've just had a good look through the forum and feel a little more enlightened now. Plenty of food for thought.

There's sealant and there is sealant. These days the stuff can be engineered. High modulus sets with very little elasticity and whenever needed to be removed it is generally easy and not messy as it forms an homogenous mass and comes off in a oner. Bathroom type sealant is messy of course (lower modulus).

I just feel that whatever the set backs are, they can be overcome by design.

I think one of the main problems here is that when we see a botched job using the ubiquitous super glue or gungy sealant, it heightens are feelings to the old craftsman's methods.

There's a nice thread on "The 21st Century Box" http://forum.melodeon.net/index.php/topic,7840.0.html I shall read that.
Logged
. . .

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hide Glue Pot for Reed Wax?
« Reply #50 on: March 09, 2018, 09:09:18 PM »

On a more sensible tack I am not sure how you would apply a sealant, admittedly I only have experience of the bathroom type. With wax you can just lay the reed plate in place, apply a small amount of wax top and bottom, ensure the reed plate is fully seated then just run more wax around to seal the plate. I envisage with sealant that the plate would need to be firmly held in place before the sealant is run around the reed plate using some sort of pump/gun mechanism.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hide Glue Pot for Reed Wax?
« Reply #51 on: March 09, 2018, 09:21:12 PM »

If you want an improved method for fixing reeds then screw fixing is the way.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hide Glue Pot for Reed Wax?
« Reply #52 on: March 09, 2018, 10:11:30 PM »

Serious question, not wanting to sound controversial but what might be wrong about using a high modulus sealant in place of beeswax/resin
It would be difficult and time consuming to use sealant, whereas applying wax can be done very quickly esp if you use a wax spoon (Charlie Marshall sells them). I have used sealant on shed windows, in the bathroom and also to seal lights on the back of a crappy little French car, but it always goes all over the place and is messy. Reed plates are generally small and delicate and require a bit of finesse when attaching them to a reed block. After all it's a musical instrument and not a replacement pipe on your toilet. If sealant was superior I'm sure the Italian makers would use it. But it isn't and they don't. (:)

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hide Glue Pot for Reed Wax?
« Reply #53 on: March 10, 2018, 10:48:26 AM »

There's sealant and there is sealant. These days the stuff can be engineered. High modulus sets with very little elasticity and whenever needed to be removed it is generally easy and not messy as it forms an homogenous mass and comes off in a oner.
The beauty of using wax is that the reed plate(s) can be removed and worked on (re-valving, reversing, etc) and then re-fixed and be useable within a very short space of time - typically less than a minute for the wax to cool and solidify. No waiting for sealant (however high-tech) to set.

Reed plates are generally small and delicate and require a bit of finesse when attaching them to a reed block. After all it's a musical instrument and not a replacement pipe on your toilet. If sealant was superior I'm sure the Italian makers would use it. But it isn't and they don't. (:)
Yes - exactly what Roger has said.

Reed plates screwed on to gaskets, as Theo mentions, is an excellent method too and similarly allows for rapid repositioning and removal as needed. It also gives a good acoustic coupling between the reed plate and the reed block, which many people feel gives a superior sound.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hide Glue Pot for Reed Wax?
« Reply #54 on: March 10, 2018, 12:04:52 PM »

It also gives a good acoustic coupling between the reed plate and the reed block, which many people feel gives a superior sound.
But it rather depends on the acoustic transmission properties of the leather used as a gasket. I'm told red leather is particularly good, especially with brass reed plates.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Barlow

  • Bad player, good talker apparently
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 111
  • Castagnari Lilly B/C Erica D/G
Re: Hide Glue Pot for Reed Wax?
« Reply #55 on: March 10, 2018, 05:07:14 PM »

On a not too far removed topic, could I ask what was the general reaction to leather reed valves being replaced with plastic?
Logged
. . .

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hide Glue Pot for Reed Wax?
« Reply #56 on: March 10, 2018, 06:39:34 PM »

On a not too far removed topic, could I ask what was the general reaction to leather reed valves being replaced with plastic?

Both leather and plastic (vinyl) valves have their place.

In general, vinyl valves are cheaper and tend to last longer without curling. Leather valves tend to be quieter in action - less prone to 'rasp' on bellows changes - but the larger leather valves normally need additional springing with a steel wire and 'dot', or additional vinyl leaves.

Leather valves seem to absorb more higher frequencies so the sound of leather-valved reeds can be perceived by some as mellower than vinyl-valved reeds which tend to give a brighter sound.

There are also synthetic leather 'vileda' valves which are a cheaper alternative to the larger leather valves. Some repairers prefer not to use them perhaps on the grounds that they may harden prematurely. However, I personally have had no problem with synthetic leather valves which have been in place for at least 10 years.

On a modern-built instrument, the general practice seems to be to use vinyl valves for the mid- and higher range notes (say from G4 and up) and leather valves for the lower notes, LH bass and most of the chord notes.

(NB this thread is now drifting well off topic.)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Barlow

  • Bad player, good talker apparently
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 111
  • Castagnari Lilly B/C Erica D/G
Re: Hide Glue Pot for Reed Wax?
« Reply #57 on: March 10, 2018, 08:03:03 PM »

(Sorry) and thank you for your reply. I have a melodeon which much of this thread is relevant to me. I also have two piano accordeons purchased cheap at an auction which I have 90% stripped, and I wish to gain various knowledge before reassembly. Thank you again.

Now...back to this hide glue pot
Logged
. . .

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hide Glue Pot for Reed Wax?
« Reply #58 on: March 11, 2018, 01:43:42 AM »

That would be " Now... back to hide glue pot"  for reed wax?

I think someone mentioned they use a waxing pot for hair removal to melt their wax which seems like it would get hot enough and controllable. They go from 0 to 120 C , Malcolm mentioned wax melts at 80 to 85 C so that would leave a little room to go higher if needed to get to the right temp.

So if your hide glue pot gets to somewhere in that range you'd probably be all set.


On hide glue the video Stockaryd posted "What so good about hide glue" good video by the way!
In the video the fellow said to heat the wood your applying the glue to ( I guess that gives you more time and I would think a better bond) , do folks here do that?

I got a button on a box to fix in a different thread, it would be hard to heat the lever where the button sits using a hot air gun without knocking of more buttons off.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Hide Glue Pot for Reed Wax?
« Reply #59 on: March 11, 2018, 02:34:57 AM »

I have a small crockpot that I use mostly for hide glue.  It has a temperature control and I have 2 pencil lines to indicate the correct settings for glue and wax (warmer for wax).

For me, a small heater with built-in fan and a hair dryer have made using hide glue much more pleasant and controllable.  I put the heater on my bench to boost ambient temperature and I use the hair dryer to warm up parts before gluing.

Maybe you could cobble up some kind of sheet-metal shield to protect  the other buttons ?
Logged
Pages: 1 2 [3] 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal