Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: wood filler advice sought  (Read 3078 times)

0 Members and 1 Guest are viewing this topic.

Judd

  • Member
  • *
  • Offline Offline
  • Posts: 12
wood filler advice sought
« on: March 26, 2016, 03:48:28 PM »

Greetings all,

I am getting ready to sell my beloved Gaillard, a 3v, to move up to a 4v. Before sale, I want to undertake a repair which is mainly cosmetic, but has small potential to escalate into something more structural, so I'd like my potential buyer to have all assurances that it will be ok.

Where Bernard screwed in the bellows retainer strap, on upper side of left hand, a fissure developed a couple years ago. It doesn't affect playing, because the load of the bellows pins keeps the seal tight. However, it is possible that the load of snapping the bellows retainer strap itself could work the fissure into a more serious crack.

I'm not experienced in wood repair, but it seems to me that some kind of filler epoxy, injected by syringe, might be ideal. I think it would bond the two sides of the fissure together with a strength close to the intact wood itself. I suppose it could be wiped/finished to keep the aesthetic impact to a minimum, but open to advice or suggestions.

I also think it would be wiser not to unscrew the bellows retainer snap, but bond everything in place. However, again, open to advice and suggestions.

photo links below.

thanks all,
Judd Heartsill
Texas USA

https://dl.dropboxusercontent.com/u/32211265/DSC09709.JPG

https://dl.dropboxusercontent.com/u/32211265/DSC09711.JPG
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: wood filler advice sought
« Reply #1 on: March 26, 2016, 04:16:34 PM »

Definitely needs to be repaired because it will only get worse if left. It s a tricky one to repair because there is little opportunity for reinforcing the area.

There is only one way to repair this.  First remove the screw that is in the middle of the crack.  Don't use any kind of filler, you will just make it more difficult to do a proper repair.  Before applying any adhesive it I essential that you work out how to clamp the are so that the crack is filly closed and held firmly.  Then use Titebond II or III worked thoroughly into the full length and width of the crack, and apply your previously devised clamping.

To be candid it would be better to get it repaired by someone with experience of this kind of work.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Judd

  • Member
  • *
  • Offline Offline
  • Posts: 12
Re: wood filler advice sought
« Reply #2 on: March 26, 2016, 05:00:20 PM »

Thanks Theo. I'm doing a bit of a search locally for experience. There are some high-end antique furniture repair/restoration folks I may engage. Also planning to speak with some local luthiers.

By what method would you work the titebond into the crack? Wouldn't a firm clamping tend to extrude the glue? I may not attempt myself, but would be interested to have an informed talk with an expert...

regards,
Judd
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: wood filler advice sought
« Reply #3 on: March 26, 2016, 05:05:43 PM »

As Theo said - remove screw - adhesive in - then clamped, could be the pilot hole for the screw was too small which would cause splitting. To get enough adhesive in to the split it may need to be opened up a bit (depending on how far the split goes) or use a repair glue that is supplied with a fine syringe. If you have no woodworking skills then get it done by a pro.
Logged

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: wood filler advice sought
« Reply #4 on: March 26, 2016, 05:20:37 PM »

Wouldn't a firm clamping tend to extrude the glue?

Yes - and that's the point. You'd want to have this repaired by closing the crack, not filling it up with glue. It looks like the crack has formed along the grain of the wood, and it's not that uncommon a damage.

The guitar-repair community has a great trick when 'massaging' wood into very fine cracks: Get as much as you can into it, and then work along the crack with a suction cup (the kind for getting sunscreens etc. to stick to your car window etc.). The pushing and pulling of the cup on top of the crack will get more glue into the crack than conventional methods. Wipe away excess, clamp tight, and wait. You'd want as much ooze-out as possible, without over-claping it (be careful along the edges).

But, agreeing that it would be a good idea to leave this up to an experienced luther, to avoid decreasing the value of a fine instrument if the result is not structually or cosmetically good.
Logged

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: wood filler advice sought
« Reply #5 on: March 26, 2016, 05:22:35 PM »

I've had to repair a similarly-placed crack on my Pariselle box when I was assembling it, and Emmanuel suggested the same repair as Theo, which worked great. I had the benefit of doing it before the panel was glued in place, so clamping was easier for me.
Logged

Judd

  • Member
  • *
  • Offline Offline
  • Posts: 12
Re: wood filler advice sought
« Reply #6 on: March 26, 2016, 08:42:27 PM »

Thanks everyone for the advice. I've left the box with a local veteran luthier, whose idea for the repair was exactly in line with everyone here, including method and materials. As always the melodeon.net folks are a big help

regards
Judd
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: wood filler advice sought
« Reply #7 on: March 26, 2016, 09:53:44 PM »

A couple of years ago I was asked to repair an almost identical damage in a Castagnari. I decided to drill 2 holes from the edge, using a 1,8 mm drill bit, both holes were then widened with a 2,3 mm bit down to crack (finishing with a 4 mm bit to make room for the screw heads). I widened the crack slightly, filled it with glue and applied 2 countersunk wood screws (Ø 2.3 mm). No clamping was necessary. Afterwards I plugged both holes with a mixture of wood dust and super glue. 
« Last Edit: March 26, 2016, 11:03:21 PM by diatonix »
Logged

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: wood filler advice sought
« Reply #8 on: March 26, 2016, 11:15:04 PM »

Academic now it is out with a luthier but with this sort of crack, close to an edge but apparently not running out of the edge, I tend to glue while the screw is still in and the crack spread, work the glue in and along with a thin wire or bristle giving as much cover as possible over the split faces, then remove the screw and be ready to clamp as Theo said if it does not close naturally.
Carefully opening up the hole when the glue has dried / cured should allow re use of the original screw if a 'special' without repeating the split.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: wood filler advice sought
« Reply #9 on: March 27, 2016, 08:30:21 AM »

With such thin wood, a nut and bolt would be less likely to cause a split or to re-open the repaired split.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Mash

  • Member
  • *
  • Offline Offline
  • Posts: 17
Re: wood filler advice sought
« Reply #10 on: March 27, 2016, 09:14:43 AM »

For future reference- where gap filling properties are required and structural strength is required, for example to hold a screw, or to tolerate the forces imposed by a strap epoxy resin should be the glue of choice . When mixed with the various cellulose and wood fibre fillers the epoxy will be at least as strong as the wood itself. Epoxy is also useful where tight clamping is not possible. In fact tight clamping is undesirable with epoxy, where as with PVA, Titebond, and polyurethane glues tight clamping is required for a good bond. I keep all these adhesives in my workshop, using them as appropriate .
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: wood filler advice sought
« Reply #11 on: March 27, 2016, 10:26:38 AM »

Logged

Chris Mash

  • Member
  • *
  • Offline Offline
  • Posts: 17
Re: wood filler advice sought
« Reply #12 on: March 27, 2016, 12:18:33 PM »

I'm not sure what you are questioning. I read your link and I notice that it doesn't mention the word resin, but resin it is. Araldite is the best known but not the best for woodwork where you might want to adjust the viscosity for gap filling or making a radiused fillet. I will be using West Systems epoxy to glue up the boxes together with their aluminium soundboards/tables of the two instruments that I am making at the moment. Epoxy resin is very good at bonding aluminium. If they had wooden tables I would use Titebond 3 (wood to wood). I think that the link that you provided overstates any problem with toxic fumes. Epoxy is remarkably pleasant to use when compared to polyester laminating resin (commonly known as fibreglass).
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: wood filler advice sought
« Reply #13 on: March 27, 2016, 02:35:23 PM »

Even when trying very hard, as a melodeon builder I can't think of any circumstance where I would recommend epoxy glue, be it Araldite or any of the other brands I've come across. And definitely not where aluminum is involved.
Logged

Chris Mash

  • Member
  • *
  • Offline Offline
  • Posts: 17
Re: wood filler advice sought
« Reply #14 on: March 27, 2016, 02:46:48 PM »

Would you please say why not. What adhesive would you use to bond aluminium to wood.

Chris
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: wood filler advice sought
« Reply #15 on: March 27, 2016, 05:13:47 PM »

Been in the professional woodworking trade for 30 years - Cabinet making, furniture making and repair, joinery, carpentry and guitar making etc. Never used apoxy resin to glue wood in all that time.

The best glue for woodworking is a wood glue - the glue shouldn't be gap filling it's to join the wood making a seamless joint IMHO.

I don't think he's bonding wood to aluminium here, for interest why are you bonding wood to aluminium?
« Last Edit: March 27, 2016, 05:18:47 PM by Gromit »
Logged

Chris Mash

  • Member
  • *
  • Offline Offline
  • Posts: 17
Re: wood filler advice sought
« Reply #16 on: March 27, 2016, 05:46:46 PM »

I am a retired technology teacher, that includes materials technology. There are times when the inherent strength of epoxy is a distinct benefit. Epoxy is used extensively in the wooden boat building industry. Modern synthetic resins have their place. Titebond is an aliphatic resin. I wouldn't dream of using epoxy where it wasn't necessary. Both the 3 voice boxes that I am building at the moment have aluminium tables/sound boards and the optimum adhesive to bond the tables into the rebates of the right hand boxes is epoxy imho. The left hand tables are wood so the rest of the structure will be glued with Titebond 3. Bye the way when I make violins I use animal glue throughout.

Chris
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: wood filler advice sought
« Reply #17 on: March 27, 2016, 06:23:19 PM »

I know that epoxy is used in boatbuilding but this is repair to a cabinet.

Interesting that you glue the aluminium to wood I guess that the wood is of a small enough thickness to not have a movement problem (there are flooring adhesives that allow the wood to expand and contract without splitting).

Yes have used animal glue for instrument building and veneering but it can be smelly :)
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: wood filler advice sought
« Reply #18 on: March 28, 2016, 11:05:45 AM »

With your background in materials technology I'm sure you understand the choice of adhesive for differing materials and I can understand why you feel that epoxy is amongst the best to stick to aluminium.  I've used a lot of different glues in boat repairs, though typically one is working in wood and GRP, epoxy is often chosen as it adheres to the original polyester layup much better than polyester does.  I'm told that the old GRP surface can be reactivated by softening it with acetone to achieve a chemical bond with fresh polyester resin, but so far I've been too cowardly to try it!

In th OP's situation I would entrust the repair to a Luthier, as he has chosen to do.  If it were a box of significantly less value I might be tempted to use some unthickened epoxy worked into the crack, but the down side is that any that weeps out would be a nigh on impossible to remove without leaving a stain.  If you have a few years to wait, UV light will eventually break it down though. ;D  I would also have to admit that sometimes my fitting skills leave a less than perfect glue line and using the sawdust generated in the work to thicken some epoxy does make for a less noticeable glue line.  Well supported wood to wood joints can often be glued with an expanding polyurethane glue which has as good a gap filling ability as thickened epoxy, but the colour will never match.

One of the strange joys of a new box is the waft of animal glue as you expand the bellows...

Rob.
Logged

Chris Mash

  • Member
  • *
  • Offline Offline
  • Posts: 17
Re: wood filler advice sought
« Reply #19 on: March 28, 2016, 05:31:25 PM »

I agree with much of what you have said. To be honest without seeing the original problem I wouldn't want to comment specifically. I sensed that there were some structural issues involved. Polyurethane glue does have very good gap filling properties, but the foamed filling has very little structural strength whereas epoxy..... I fear that we are getting into a rather theoretical discussion. As I have said earlier l keep all these adhesives in my arsenal and use them as appropriate.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal