Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Help - bellows glued on!  (Read 2838 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Help - bellows glued on!
« on: June 27, 2017, 03:58:31 PM »

Help and advice needed Melnet hive mind.

I've just been asked to renovate a Hohner Club 235, its a 4 voice beast with helicon bass,  not perfect condition externally, but not too bad and definitely worth restoring.  The reeds need some work of course and there is the problem.  Some clever person has glued the bellows frames to the ends, at both ends.  Any idea how I might get the bellows separated?

So far I have tried running a sharp knife through the bellows gasket, but nothing has budged yet.  Next to try is a sharper knife with a thinner blade than can cut through to the bellows frame.   I have a horrible feeling that the glue extends up the spigot on the bellows frame.

In the end I might have to just cut the bellows off the frames, and may even need to destroy the frames to get them off.  Before that I want to exhaust other possibilities, and also to locate a spare bellows and frames for this model.

The glue is dark brown, hard and brittle.  It might be very old contact adhesive or it might be shellac.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Help - bellows glued on!
« Reply #1 on: June 27, 2017, 04:20:47 PM »

Hot knife
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Help - bellows glued on!
« Reply #2 on: June 27, 2017, 04:26:01 PM »

Thanks John, I'll try that.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

ACE

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 535
Re: Help - bellows glued on!
« Reply #3 on: June 27, 2017, 04:30:11 PM »

Steam?
Logged
Paddy Clancy, paddlewheel gob iron cheepo g/d anglo

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Help - bellows glued on!
« Reply #4 on: June 27, 2017, 04:31:03 PM »

Have you tried acetone Theo ? Failing that or other solvent, a router and fence would control depth & width of cut so only bellows frame sacrificed"
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Andy

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 159
Re: Help - bellows glued on!
« Reply #5 on: June 27, 2017, 04:44:42 PM »

Sounds like it could be animal glue (pearl glue) in which case would agree heat should do the trick.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Help - bellows glued on!
« Reply #6 on: June 27, 2017, 05:01:22 PM »

Have you tried acetone Theo ? Failing that or other solvent, a router and fence would control depth & width of cut so only bellows frame sacrificed"

Acetone is not safe near celluloid,  so is definitely not on.

Sacrificing the bellows frame is the last resort, and preferably only if I can locate a replacement set of frames.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Help - bellows glued on!
« Reply #7 on: June 27, 2017, 05:38:02 PM »

Is there enough to scrape some off into a saucer so that you can experiment with solvents away from the box?

At risk of stating the obvious, even old pearl glue will become sticky again when exposed to hot water, for identification.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Help - bellows glued on!
« Reply #8 on: June 27, 2017, 06:06:46 PM »

I use a wide piece of planed oak as a sort of bolster, lay the accordion on the bench and apply gently hammer blows to the oak bolster, with the sharp corner of the oak against the frame and direction of impact parallel to the case, to drive the frame away from the case. It sounds a bit brutal, but it does work with very jammed bellows frames.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Help - bellows glued on!
« Reply #9 on: June 27, 2017, 06:26:56 PM »

I use a wide piece of planed oak as a sort of bolster, lay the accordion on the bench and apply gently hammer blows to the oak bolster, with the sharp corner of the oak against the frame and direction of impact parallel to the case, to drive the frame away from the case. It sounds a bit brutal, but it does work with very jammed bellows frames.

I was going to suggest some sort of mechanical shock but Roger has beaten me to it.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Help - bellows glued on!
« Reply #10 on: June 27, 2017, 06:38:54 PM »

I had a similar problem once: I took off the bellows from its frames which made the whole process a lot easier, without leaving ugly marks on the casings.
« Last Edit: June 27, 2017, 10:23:28 PM by diatonix »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Help - bellows glued on!
« Reply #11 on: June 27, 2017, 06:56:52 PM »

I use a wide piece of planed oak as a sort of bolster, lay the accordion on the bench and apply gently hammer blows to the oak bolster, with the sharp corner of the oak against the frame and direction of impact parallel to the case, to drive the frame away from the case. It sounds a bit brutal, but it does work with very jammed bellows frames.

I was going to suggest some sort of mechanical shock but Roger has beaten me to it.

Thanks for that reminder.  I've done that once before but had forgotten. Probably my mind trying to erase a bad memory!  My bolster succeeded on breaking off the edges of the frame!

I'll be gentle this time!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Garry Probert

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 296
Re: Help - bellows glued on!
« Reply #12 on: June 27, 2017, 08:33:47 PM »

Hi theo don't know if this helps ,I use

http://www.stewmac.com/Luthier_Tools/Tools_by_Job/Tools_for_Necks_and_Fingerboards/Neck_Joint_Steamer.html?utm_source=google&utm_medium=shopping&utm_campaign=2017-06-gp&pref_currency=P&shipcalc=UK&gclid=CMn396vf3tQCFW0z0wodV2wP7g

 to loosen hide glue guitar neck joints to reset but would be concerned about excessive moisture in a melodeon but it might be small enough to insert in the bellows pin holes
I have stripped several of darrens old boxes and one appeared to have been cut mid bellows then card lapped repaired
now you have mentioned the possibility that they could of been glued together .
I assuming this was done to gain access to the frames from the inside ,possibly with a hot knife to save the bellows frames

 
Logged

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: Help - bellows glued on!
« Reply #13 on: June 27, 2017, 08:35:36 PM »

I had a similar prolem once: I took off the bellows from its frames which made the whole process a lot easier, without leaving ugly marks on the casings.

I was thinking that might be a good strategy, but I've never (yet!) needed to try it.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Help - bellows glued on!
« Reply #14 on: June 27, 2017, 09:23:04 PM »

Hi theo don't know if this helps ,I use

http://www.stewmac.com/Luthier_Tools/Tools_by_Job/Tools_for_Necks_and_Fingerboards/Neck_Joint_Steamer.html?utm_source=google&utm_medium=shopping&utm_campaign=2017-06-gp&pref_currency=P&shipcalc=UK&gclid=CMn396vf3tQCFW0z0wodV2wP7g

 to loosen hide glue guitar neck joints to reset but would be concerned about excessive moisture in a melodeon but it might be small enough to insert in the bellows pin holes
I have stripped several of darrens old boxes and one appeared to have been cut mid bellows then card lapped repaired
now you have mentioned the possibility that they could of been glued together .
I assuming this was done to gain access to the frames from the inside ,possibly with a hot knife to save the bellows frames

 

I'm wary of using steam because the carcase of the instrument is plywood and there is a risk of the ply beginning to delaminate.

If I have to cut the bellows off the frame I will cut through the glued joint between the last fold and the frame.  That way both the bellows and the frame can be re-used.   
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Help - bellows glued on!
« Reply #15 on: June 27, 2017, 09:43:47 PM »

I've got a reciprocating saw which I used to cut through some floorboard nails, where the boards had been nailed from underneath into skirting boards. it is quite gentle in its relentlessness.
You're welcome to borrow it for a try.
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Garry Probert

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 296
Re: Help - bellows glued on!
« Reply #16 on: June 27, 2017, 09:59:56 PM »

Hi theo that seems the most logical approach,the mini steamer was a godsend suggested to me by an old but innovative luthier many years ago "you can teach an old dog lol"
Darrens middle split melodeon bellows seemed a little drastic but i couldn't for the life of me see a reason for doing it.   
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Help - bellows glued on!
« Reply #17 on: June 28, 2017, 02:36:22 AM »

If the glue is "brittle" as stated in the original post, something like a very, very small jack hammer, if there is such a thing, though ones I've encountered would probably be too big and powerful. Anyone know of such a tool? Maybe even an old steel rule tapped with a hammer may be enough to shatter brittle glue without doing much, if any, damage elsewhere. Might loosen a few reedplates, but a small price to pay....
Logged
Tuner/repairer, now retired.

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: Help - bellows glued on!
« Reply #18 on: June 28, 2017, 03:02:20 AM »

One of the most useful tools I've bought in recent years is a Japanese Flushcut Saw, similar to this one: Ice Bear Japanese Kugihiki Flushcut Saw AP300326

The blade is very narrow, with no offset on the teeth, so it makes a very fine cut without damage to either side of it. It would easily go into the gap between the instrument end and the bellows frame, where the gasket should be.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Help - bellows glued on!
« Reply #19 on: June 28, 2017, 07:21:30 AM »

Good idea Triskel.  I have one of those, but mine is a cheap German version from Lidl!  Ideal for cutting through glue soaked leather.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal