Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Setting a reed on a Giordy  (Read 1199 times)

0 Members and 1 Guest are viewing this topic.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Setting a reed on a Giordy
« on: October 05, 2018, 05:00:31 PM »

The pull E on the G row of my Giordy is slow to play and breathy. OK once it's going but annoying when trying to play quietly.

The reeds are flat mounted. Any thoughts on how to get at it to set it, or is flipping it the only option?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Setting a reed on a Giordy
« Reply #1 on: October 05, 2018, 05:09:29 PM »

Giordys are particularly difficult to set as the pressure in the bellows is, due to the small capacity, higher than normal so the setting of the reed is very sensitive. I would probably pop the reed off and look at the set and adjust it a little then wax it back. This will of course change its tuning  :(

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Setting a reed on a Giordy
« Reply #2 on: October 05, 2018, 06:01:04 PM »

The pull E on the G row of my Giordy is slow to play and breathy. OK once it's going but annoying when trying to play quietly.

The reeds are flat mounted. Any thoughts on how to get at it to set it, or is flipping it the only option?
Even with flat-mounted reeds, you should be able to access the pull reed using a reed lifter to bring the tongue up through the slot. My preferred lifter is the Italian hook-shaped type, but the German flat pointy type should work too. Once you have the reed lifted, slide a cocktail stick* or wooden skewer* between the reed tongue and the reed plate and gently ease it upwards a few times. This should encourage a gap setting which is narrower than the previous setting.

Release the reed tongue and try out the reed response. Repeat if necessary. If you go too far and the reed chokes off, or has a weak sound, use the cocktail stick through the slot to push the reed tongue down to open up the gap a bit. Try out the response again.

Reiterate opening or closing the gap until the response is optimum. Then adjust the tuning as necessary.

As Lester has mentioned, the Giordy setting is particularly sensitive to small changes, but having worked on a couple of Giordys in the last few months, it is nevertheless possible to get the reed(s) performing properly without needing to remove the reed plate from the block.

* Readily available improvised tools. However, for reed setting, I use a dentists' hand descaling tool (from Ebay/Amazon, etc) which is made of soft steel, softer than the reed tongue so won't scratch it, but less prone to sliding off than the wooden cocktail stick/skewer.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Setting a reed on a Giordy
« Reply #3 on: October 10, 2018, 10:29:31 PM »

Thanks for the suggestions, I will have a play when I have some time.
Malcolm
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal