Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: How I Learned to Stop Worrying and Fettle the Box  (Read 1672 times)

0 Members and 1 Guest are viewing this topic.

Eshed

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 447
How I Learned to Stop Worrying and Fettle the Box
« on: April 01, 2019, 12:21:36 PM »

I've been planning to do some work on my boxes for quite some time, but Lester's Hot Rod your Hohner and the recent arrival of needed materials prompted me to actually roll up my sleeves and get to it.
I'm going to try and in this thread what happens to mortals with some mechanical sense who attempt to follow Lester's series.
(my first post was in Lester's thread but I'm moving my discussion here so people who see new posts there aren't disappointed that it's me and not a new episode)

The box in question is a Hohner Club IIB Victoria, which is a bit different from the Pokerwork, but I think many things are transferable.

I suspect this box has been fettled in the past for two main reasons:
1) There were two types of pallet facing: The pallets of the two main treble rows had 1-layer facing while the bass and the short row had green felt+leather facing. Moreover, the bass pallets were held by very weak glue while the treble pallets had a strong one (see my previous post).
2) The bellows are in a surprisingly good shape and have a diamond shape on them which AFAIK isn't a standard Hohner thing.

Refacing the pallets
Other than the need for a soldering iron, removing the pallets on both sides was ok. A file and some mildly aggressive scalpel use managed to clean the levers from the glue.
Putting the pallets in their place was mostly straightforward, holding the soundboard in front of a light to see if there are leaks was very useful.

The Good:
I've managed to get it more airtight than it was before I started, the buttons are more level, there's far less pallet noise and it's a joy to play.

The Bad:
Gluing the pallets back was easy for most of them, but the half-row are hidden behind the levers of the other rows, so I tried to drip some glue from above. This resulted in a terrible mess of pallets glued to the soundboard and to each other which took some time to clean.
All in all it's not my prettiest job ever, but It does the job and it's mostly reversible.

With the gained experience, the bass side looks much better I think.


The Ugly:
If you look carefully at the picture of the bass mechanism, there are only 7 rods  ;D
It appears the the little pins in the pokerwork are not the only thing that can split and one of the rods decided to fail when I've attempted to reinstate it


Which brings me to the current state where I have a 7-bass box to fix. I suspect I'm not the first person it happened to. Any suggestions? (using what I have or can get in a nearby store if possible)
Note that there's not enough length in the rod to both be effective and go through the mechanism, I've tried.
« Last Edit: April 01, 2019, 12:31:48 PM by Eshed »
Logged
Do you have a Hohner from 1934-1945 with a serial number on?
Send me a private message or comment on the German Accordion Problem spreadsheet to improve the statistics of the project and get an estimate of the production date of the box if it is not known.

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #1 on: April 01, 2019, 12:56:04 PM »

Looks very like galvanised fence wire to me. That's easy to get.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #2 on: April 01, 2019, 12:59:00 PM »

I have a selection of old wire coat hangers in the workshop that I use to replace this sort of stuff. Hardest part is normally removing the old rod from the button, but a bit of heat from a soldering iron on the rod usually suffices.

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #3 on: April 01, 2019, 01:02:36 PM »

Hence "Hot Rod a Hohner"

(I'll get my coat...)
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #4 on: April 01, 2019, 02:37:52 PM »

Hence "Hot Rod a Hohner"
  8)

The glue blobs are ugly, but that's par for the course. Have any of you hot-rodders (and I don't mean our friend "Straddling") considered using eyelets / grommets / squidgy plastic rings or whatever various means the Gaillards of the world use to attach levers to pallets?
« Last Edit: April 01, 2019, 02:48:04 PM by Stiamh »
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #5 on: April 01, 2019, 03:10:05 PM »


Hence "Hot Rod a Hohner"
  8)

The glue blobs are ugly, but that's par for the course. Have any of you hot-rodders (and I don't mean our friend "Straddling") considered using eyelets / grommets / squidgy plastic rings or whatever various means the Gaillards of the world use to attach levers to pallets?
The 'eyelets / grommets / squidgy plastic rings' are part of a whole system used to manufacture the action and as such probably would not work with the Hohner action

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #6 on: April 01, 2019, 08:55:35 PM »

With practice hot glue can be applied neatly.  Here is one I did earlier.  It’s worth practicing on a bit of cardboard to get a good technique. 

I’ve found the following to be helpful:

Make sure the glue gun is thoroughly warmed up.  I tend to leave it on at least 5 minutes before I’m read to start.

Keep the nozzle in contact with the surface you are applying glue to.

Move the nozzle back as you squeeze out a bead of glue.

When finished hold the nozzle above the newly deposit glue and move it around so that the strand of stretched out glue falls back and is incorporated onto the still hot bead below. This minimises the amount of glue filament that you have to remove afterwards.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #7 on: April 01, 2019, 10:04:38 PM »

Some people use wax instead of glue. I used PVA and scrim discs.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #8 on: April 01, 2019, 11:44:05 PM »

Carry some sidecutters when out and about Eshed, don't get greedy, most cyclists will not notice the loss of a single spoke until well away from where you are covertly operating, samples from a variety of cycles may yield a variety of gauges of wire..................

NB this is the one time you can ignore it being April 1st  >:E
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #9 on: April 02, 2019, 05:01:57 AM »

I like using bicycle spokes for several reasons: they are stiffer than coat hangers or fence wire, can be had in many guages, available in stainless steel if desired. I also make spokes into flexible drill bits which can be used to drill curved holes.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Eshed

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 447
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #10 on: April 09, 2019, 01:22:00 PM »

I've used a coat hanger since it was the most accessible.
My box is now back to 8-bass.
Also visible in the attached picture is recycling of felt+leather to create movement restriction on the bass side which seems to work ok so far.

Thank you everyone for your help!
« Last Edit: April 09, 2019, 01:25:44 PM by Eshed »
Logged
Do you have a Hohner from 1934-1945 with a serial number on?
Send me a private message or comment on the German Accordion Problem spreadsheet to improve the statistics of the project and get an estimate of the production date of the box if it is not known.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: How I Learned to Stop Worrying and Fettle the Box
« Reply #11 on: April 10, 2019, 08:02:35 PM »

Gluing pallets in awkward position (e.g. the lowest row on a Corona). I use tweezers to position the pallets and then check they are all airtight, by holding it up to a bright light. I make some little square patches, or reuse the round linen ones that were on there. Apply blob of solvent free bostick to the patch and position on the pallet with two pairs of tweezers. It sounds tricky but it works quite well, avoids the glue going all over and is actually quite quick to execute. That’s how I do it anyway. I’ve tried blobbing glue between the levers and just end up making a horrible mess.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal