Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3   Go Down

Author Topic: Contact adhesive for vinyl valves  (Read 7196 times)

0 Members and 1 Guest are viewing this topic.

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Contact adhesive for vinyl valves
« Reply #20 on: May 01, 2019, 06:24:27 AM »

[quote author=Steve_freereeder

Hmm... If it's latex based, I'm not sure I would trust a metal-to-vinyl bond to hold for any significant time. In my experience latex adhesives (e.g. 'Copydex') tend to go all gooey and fail after a while. But maybe your experience with this product is OK.
[/quote]

Exactly what I said. (:)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Contact adhesive for vinyl valves
« Reply #21 on: May 01, 2019, 12:45:19 PM »

My experience has been fine so far, but perhaps I should reconsider given the general consensus here on that type of product...
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Contact adhesive for vinyl valves
« Reply #22 on: May 01, 2019, 01:20:06 PM »

I use this one, Bostik Solvent Free, climate emergency, etc.
https://www.ebay.co.uk/itm/Bostik-Solvent-Free-Extra-Strong-Safe-Adhesive-50ml-DIY-Crafts-Household-Glue/362397255532?epid=1626534908&hash=item54608f476c:g:LBQAAOSwZltb4FQ-
This was recommended by Rees a few years ago and I’ve used it since then. It has these advantages...it takes a few minutes to dry so for mass valvings..it’s good to put blobs onto a sheet of card and use from there rather than the end of the tube. And it is solvent free so you don’t get high on it. For one off/single valves I use UHU or cheap equivalent. Dries more rapidly and also dries hard, so removal is easier. I tried the contact adhesive and found it tricky to use. You are *supposed* to put a thin layer on each surface, wait for it to dry, then stick. Wilkos (a cheap store in the UK) do their own contact adhesives, in the same coloured tube (red) as the market leader, but it is poor stuff in comparison. It is cloudy and gummy and sets almost the moment it is exposed to air. So I don’t use it...or the expensive contact adhesive, for valves. But as we can see, opinions differ widely. NickCB warned me off Copydex a few years ago. It’s vile stuff.
I keep meaning to try gasket sealer, which apparently is what uses to be used. Nice and easy to clean off. I once came across an accordion with valves glued on with epoxy. I couldn’t get the glue off at all.
« Last Edit: May 01, 2019, 01:22:01 PM by RogerT »
Logged

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Contact adhesive for vinyl valves
« Reply #23 on: May 01, 2019, 02:42:29 PM »

Get it here, if you're quick
https://www.ebay.co.uk/itm/Bostik-Contact-Adhesive-Tube-50Ml-Household-Repairs-DIY-Tools-Home-Garage-New/332126614649?epid=1330584098&hash=item4d5449f479:g:YvcAAOSwDk5UCXRW

Thanks! I just ordered a tube. Should keep me going for a bit longer!
I can almost grantee you'll get the purple tube & not what it shows in the picture.. :( I sould have said how I found out the changes
 
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Contact adhesive for vinyl valves
« Reply #24 on: May 01, 2019, 03:00:04 PM »

Get it here, if you're quick
https://www.ebay.co.uk/itm/Bostik-Contact-Adhesive-Tube-50Ml-Household-Repairs-DIY-Tools-Home-Garage-New/332126614649?epid=1330584098&hash=item4d5449f479:g:YvcAAOSwDk5UCXRW

Thanks! I just ordered a tube. Should keep me going for a bit longer!
I can almost grantee you'll get the purple tube & not what it shows in the picture.. :( I sould have said how I found out the changes
 
Oh dear. Well - we shall see! If I get the purple tube I'll use it for experimental fixing of a vinyl valve on a spare/scrap reed plate. Will report back here...
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Contact adhesive for vinyl valves
« Reply #25 on: May 01, 2019, 03:03:26 PM »

You are *supposed* to put a thin layer on each surface, wait for it to dry, then stick.

I never bother doing that for valves. I just spread some glue on the end of the valve and immediately press it into place on to the reed plate. There is enough leeway time to allow for slight repositioning if neeeded. Works fine for me.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Contact adhesive for vinyl valves
« Reply #26 on: May 01, 2019, 03:13:33 PM »

Get it here, if you're quick
https://www.ebay.co.uk/itm/Bostik-Contact-Adhesive-Tube-50Ml-Household-Repairs-DIY-Tools-Home-Garage-New/332126614649?epid=1330584098&hash=item4d5449f479:g:YvcAAOSwDk5UCXRW

Thanks! I just ordered a tube. Should keep me going for a bit longer!
I can almost grantee you'll get the purple tube & not what it shows in the picture.. :( I sould have said how I found out the changes
 
Oh dear. Well - we shall see! If I get the purple tube I'll use it for experimental fixing of a vinyl valve on a spare/scrap reed plate. Will report back here...

I'll crawl back under my stone  :|bl
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Contact adhesive for vinyl valves
« Reply #27 on: May 01, 2019, 04:30:55 PM »


[/quote]
I'll crawl back under my stone  :|bl
[/quote]
pay Steve his £6.30 back  (:), when I saw the red tube I did ask the seller and his confirmed it's the purple one on the actual picture.I would have bought them all..never mine new one is still good to use just be very careful on the smaller valves.might help to know I use hole punch reeds,you might not have have an issue if use valve without the hole at the base as the are little bit more stronger
.what Rees uses should be more than good enough for us I'll get some of them solvent free ones to see.   
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Contact adhesive for vinyl valves
« Reply #28 on: May 01, 2019, 08:29:44 PM »

You are *supposed* to put a thin layer on each surface, wait for it to dry, then stick.

I never bother doing that for valves. I just spread some glue on the end of the valve and immediately press it into place on to the reed plate. There is enough leeway time to allow for slight repositioning if neeeded. Works fine for me.

Ditto.
Logged
C#/D player

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Contact adhesive for vinyl valves
« Reply #29 on: May 03, 2019, 02:10:44 AM »

I was steered to Uhu from this forum quite a while back, and have had good luck with it.  And I got it through Amazon in the US.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Contact adhesive for vinyl valves
« Reply #30 on: May 04, 2019, 01:20:39 PM »

The tiniest weensiest drop of reed wax on the tip of a very small brush...

I did this last night after accidentally pulling a valve flap off the reed next to the one I was waxing in. I don't know how long it will last but the reed is sounding alright and the adhesive was readily available.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Contact adhesive for vinyl valves
« Reply #31 on: May 04, 2019, 01:39:46 PM »

But when the wax fails and and the reed falls off the wax left on the reed will make it harder for adhesives to stick securely.  Almost any other adhesive would be better than wax.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Contact adhesive for vinyl valves
« Reply #32 on: May 04, 2019, 02:27:15 PM »

... I tried the contact adhesive and found it tricky to use. You are *supposed* to put a thin layer on each surface, wait for it to dry, then stick...

At the risk of spreading more egg on my face, I think that is impact adhesive, not contact adhesive ("traditional" Evostick rather than "traditional" Bostik). If you do that with a contact adhesive it won't stick.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Contact adhesive for vinyl valves
« Reply #33 on: May 04, 2019, 02:49:27 PM »

... I tried the contact adhesive and found it tricky to use. You are *supposed* to put a thin layer on each surface, wait for it to dry, then stick...

At the risk of spreading more egg on my face, I think that is impact adhesive, not contact adhesive ("traditional" Evostick rather than "traditional" Bostik). If you do that with a contact adhesive it won't stick.

I don't think so. The Bostik Solvent Free Contact adhesive that I use is best left for anything up to 15 minutes before attaching - but as others have said, if you attach immediately it leaves some wiggle room. Whichever method you use it's great valve glue.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Contact adhesive for vinyl valves
« Reply #34 on: May 04, 2019, 03:30:33 PM »

... I tried the contact adhesive and found it tricky to use. You are *supposed* to put a thin layer on each surface, wait for it to dry, then stick...

At the risk of spreading more egg on my face, I think that is impact adhesive, not contact adhesive ("traditional" Evostick rather than "traditional" Bostik). If you do that with a contact adhesive it won't stick.

I don't think so. The Bostik Solvent Free Contact adhesive that I use is best left for anything up to 15 minutes before attaching - but as others have said, if you attach immediately it leaves some wiggle room. Whichever method you use it's great valve glue.
I agree
“contact adhesive” sticks on contact or should if used properly (:) the method Roger suggested is what’s on the label of the stuff I use ( water or solvent based)and would be required if the material is porous ( sometimes an extra coat is required or material won’t stick) for it to stick. It won’t stick well if you set it wet, before it gases off and dries. This kind of full strength bond is not required to stick down a valve anyway so a small dab of glue on a smooth surface wet or dry would do it.

I used the stuff Charlie sells it work great, have a tissue or cloth handy the tube tip gets gummed up quickly. Could be I need to work faster!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Contact adhesive for vinyl valves
« Reply #35 on: May 05, 2019, 07:32:08 AM »

Glue! Always an interesting subject! On the alleged difference between impact and contact adhesive the inter web is full of 'info' e.g. like this....
https://www.diy-forums.com/threads/adhesive-question.256469/

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Contact adhesive for vinyl valves
« Reply #36 on: May 05, 2019, 07:53:29 AM »

Using contact adhesive correctly requires one to get the positioning accurate on the first attempt, as there isn't a second one.
I often need to make a slight adjustment.
Then it relies on the valves not getting disturbed or blown around while drying. And some waiting around while they dry, without going to make a coffee, getting distracted, finding another little job that needs doing, and eventually remembering the valves to find the glue completely dry and useless.
Using it wet means that it doesn't matter how long I leave it and it's much easier to handle while drying.

However, I do find occasionally that a valve curls at the glue end, or otherwise distorts, and has to be re-done. Haven't worked that out yet. I normally use UHU.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Contact adhesive for vinyl valves
« Reply #37 on: May 05, 2019, 08:00:45 AM »

Using contact adhesive correctly requires one to get the positioning accurate on the first attempt, as there isn't a second one.
I often need to make a slight adjustment.
Then it relies on the valves not getting disturbed or blown around while drying.
Neither of these are true in my experience. I use EvoStick contact, small amount on the valve, position/adjust the valve, job done. Can be played straight away. I have none many many valves this way.


The only advice I would offer on valve glueing is to be sure no adhesive is squished out and touching the adjacent reed as this is a real pain to discover and clean up.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Contact adhesive for vinyl valves
« Reply #38 on: May 05, 2019, 08:26:13 AM »

Neither of these are true in my experience. I use EvoStick contact, small amount on the valve, position/adjust the valve, job done.
Yes, that is exactly what I meant by using it wet.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Contact adhesive for vinyl valves
« Reply #39 on: May 09, 2019, 02:22:32 PM »

Get it here, if you're quick
https://www.ebay.co.uk/itm/Bostik-Contact-Adhesive-Tube-50Ml-Household-Repairs-DIY-Tools-Home-Garage-New/332126614649?epid=1330584098&hash=item4d5449f479:g:YvcAAOSwDk5UCXRW

Thanks! I just ordered a tube. Should keep me going for a bit longer!
I can almost grantee you'll get the purple tube & not what it shows in the picture.. :( I sould have said how I found out the changes
 
Oh dear. Well - we shall see! If I get the purple tube I'll use it for experimental fixing of a vinyl valve on a spare/scrap reed plate. Will report back here...

Update:
Yes, I did indeed receive the purple tube.  :(
However, the good news is that having tested it* with a vinyl valve on a scrap reed plate, it appears to work fine. No dissolving or distorting of the valve, and the bond appears to be perfectly satisfactory.  (:)

The only slight difference I've noticed is that the wiggle time is possibly just a little bit longer perhaps by a minute or so compared with the old style red tube.

*Thin smear of glue on the valve end only, then pressed into place on the reed plate immediately.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk
Pages: 1 [2] 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal