Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: tuning discrepencies  (Read 1429 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
tuning discrepencies
« on: September 22, 2019, 04:53:31 AM »

I'm working on a one-row, 4-stop accordion in the key of G. When tuning, I use the instrument's own bellows, holding the end frame against the instrument while I check the note in question against my tuner (and ear).  This practice has always worked well for me, however I noticed that on this instrument, the pitch of the lower notes changes noticeably from when I test it as described above, to when checking them again once the end frames have been screwed back together.  At this time I find that the pitch of the lower notes is a bit flat.  Disassembling the instrument once again to re-check I find that everything is perfectly in tune (the pitch of the reeds are as I had tuned them), but once again those notes are flat when the instrument's end frames are screwed together.  I can only assume that, despite my holding the ends together when testing, that there is some air loss which is affecting the pitch of those reeds.  This only happens with the lower notes, as about halfway up the keyboard everything else stays the same. 

This has necessitated me having to tune those reeds a little sharp in order for the pitch to be correct spot once reassembled.  This is a bit of a pain because reassembling the instrument involves four long screws, and obviously going back and forth is laborious and tedious.  I don't suppose there's another work-around? Has anyone else come across this when tuning cajun-style boxes?  The Hohner HA114s, and any one-rows that use bellows pins do not seem to have this problem.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: tuning discrepencies
« Reply #1 on: September 22, 2019, 08:01:18 AM »

Low reeds will usually drop in pitch when played louder/with more pressure.  Perhaps you need to just sound the reeds a bit harder when tuning the low notes?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: tuning discrepencies
« Reply #2 on: September 22, 2019, 09:42:41 AM »

I think tuning discrepencies like these are due to the change in rigidity of the instrument and reedblock setup when it is fully assembled, compared with when it is partly disassembled for tuning as you have described. I know from experience that the pitch of the reeds can be affected in this way, but so far, I have not been able to predict how much variation can occur, nor why some parts of the instrument are affected and not others.

The best remedy for your problem is to tune by offsets: (1) Make a note of how much the reeds are out of tune when the instrument is fully assembled. Then, (2) with the instrument disassembled for tuning, adjust the pitch of the reeds by the required amount determined from step (1). On reassembling the instrument, you should find that the reeds are now in tune, or at least acceptably close (± 0.5 cents say?)

The other variable to take into account is the transient time taken for the reeds to reach their correct playing pitch. It's a common problem with the larger reeds (especially the push reeds) which may start perhaps as much as 2 - 3 cents flat and then come up to pitch over the duration of a second or so. A compromise is to tune the lowest pitch reeds, e.g. A3 or lower, deliberately a little bit sharp (again perhaps 1 - 2 cents sharp) so that the pitch discrepency is not so noticeable when the reeds are first sounded in normal playing.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: tuning discrepencies
« Reply #3 on: September 22, 2019, 01:37:04 PM »

Low reeds will usually drop in pitch when played louder/with more pressure.  Perhaps you need to just sound the reeds a bit harder when tuning the low notes?

I wondered the same thing but using more pressure did not make a difference.

The other variable to take into account is the transient time taken for the reeds to reach their correct playing pitch.

I’m aware of this phenomenon but in this case the notes in question reach their playing pitch immediately (they are M reeds, and not the L reeds).
Logged
C#/D player

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: tuning discrepencies
« Reply #4 on: September 22, 2019, 02:02:30 PM »

Low reeds will usually drop in pitch when played louder/with more pressure.  Perhaps you need to just sound the reeds a bit harder when tuning the low notes?
I wondered the same thing but using more pressure did not make a difference.
Then I think the discrepencies are probably due to a rigidity effect, as I speculated earlier.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: tuning discrepencies
« Reply #5 on: September 22, 2019, 03:40:03 PM »

Quote
I’m aware of this phenomenon but in this case the notes in question reach their playing pitch immediately (they are M reeds, and not the L reeds).

Interesting.  Do you have the problem with both sets of M reeds or just one of them ?  Is it a standard 4-voice with glued-in blocks ? 
« Last Edit: September 22, 2019, 03:48:24 PM by tirpous »
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: tuning discrepencies
« Reply #6 on: September 23, 2019, 02:44:28 PM »

That’s a very good question. I will check tonight. It is a standard 4-stop one-row with glued-in, upright blocks (a Beltuna).
Logged
C#/D player
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal