Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4   Go Down

Author Topic: Pokerwork clacking  (Read 16087 times)

0 Members and 1 Guest are viewing this topic.

HallelujahAl

  • Guest
Re: Pokerwork clacking
« Reply #40 on: September 24, 2009, 04:49:26 PM »

Theo do you apply the same process to a three row (I'm thinking of my Trichord)?
AL
Logged

juker

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 838
  • Hohner 2 row G/C and C/F,
    • Julie's Art'nAll
Re: Pokerwork clacking
« Reply #41 on: September 24, 2009, 05:45:30 PM »

Yes, the noise on mine comes when the buttons are released too. I didn't notice it was 'clacky' until I listened to the video of myself I made for youtube - I don't know anyone else who plays a box, so nothing to compare my sound to. Do any of these ideas improve the clackiness that comes from the buttons hitting the fingerboard? Both treble and bass buttons make a noise on my Hohner.

That noise on releasing the buttons is caused by the pallets, with thin leather facing, hitting the base board.   The solution to this is to re-face the pallets with a softer material - leather with a layer of felt underneath.  I feel another set of photos may be needed.

Thanks, that would be excellent, if it is not too much trouble  (:)
Logged
I don't get 'jigs'

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Pokerwork clacking
« Reply #42 on: September 24, 2009, 05:49:24 PM »

Here is a photo of the two fingerboards I purchased from Irish Dancemaster. Very nice products, I think, and fairly priced. As shipped, they are in a natural finish on teak. I opted to spray them with a gloss black urethane to match a litle more closely the the look of the original pieces -- one wood, one plastic, but both black.

There is a photo of one in the natural teak finish here: http://www.irishdancemaster.com/reedtuning.html

The only photo I have of my removeable top modification of the pressed wood fingerboard is found in an earlier post.

Bob
Logged

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Pokerwork clacking
« Reply #43 on: September 24, 2009, 09:12:59 PM »

Here is a photo of the two fingerboards I purchased from Irish Dancemaster. Very nice products, I think, and fairly priced. As shipped, they are in a natural finish on teak. I opted to spray them with a gloss black urethane to match a litle more closely the the look of the original pieces -- one wood, one plastic, but both black.

There is a photo of one in the natural teak finish here: http://www.irishdancemaster.com/reedtuning.html

The only photo I have of my removeable top modification of the pressed wood fingerboard is found in an earlier post.

Bob

Did you have to modify the wooden one much for your Erica?  I put one on a Pokerwork and all it required was a little shimming to get the angle right.
Logged

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Pokerwork clacking
« Reply #44 on: September 24, 2009, 10:26:42 PM »

The piece for the Erica was a perfect fit, just like it came from the factory.  The lyre-shaped one for the Pokerwork took the smallest amount of shimming, just a bit of cardstock between the mating faces, in order to center the buttons in the length of the slightly oblong holes.

Don't know how well it shows up in the photos, but the buttons on both these boxes are white "pearl", obtained from CGM. Put each one in a fixture on the drill press, bored a 1/8" hole on the backside, and they were a perfect press fit onto the Hohner keyrods. I think they look smart in that black fingerboard!

Bob
Logged

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Pokerwork clacking
« Reply #45 on: September 25, 2009, 02:40:37 AM »

Thanks RGF

If I can figure out how to post a picture

I'll show you the prototype I sent to Dancemaster..  this was following a request that I explore the possibility of producing them

I was sent a couple keyboards that were made by someoene else...
poor design  materials and workmanship  

So I made an upgraded version that would be suitable for either Erica or Pokerwork  old or new
and a  prototype needed to be fitted and another pre-production model made.
I decided not to pursue this and am still waiting for the return of my prototype.

I did not give anyone  permission to make it or have  these fingerboards  made
I believe I posted somethiong to that effect on the yahoo box group some time ago...
following information I had received  about the possibility that my design was being used.

The original agreement was that I would provide products of my own design should we mutually agree to pursue this.
« Last Edit: September 25, 2009, 03:13:36 PM by melodeon »
Logged

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Pokerwork clacking
« Reply #46 on: September 25, 2009, 05:02:07 AM »

Hopefully that is an issue here, as I bought both of these several years ago.
Logged

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Pokerwork clacking
« Reply #47 on: September 25, 2009, 05:26:21 AM »

Good to know.

Thanks
Logged

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Pokerwork clacking
« Reply #48 on: September 25, 2009, 08:38:31 AM »

Here are the photos on my facebook page.  This is a public link please let me know if you can't see them.

Did mine last night using this process.  Thanks a million for the step-by-step guide, which cuts out what could have been a lot of trial and error.  I used Ramin which is what I had to hand, already in 6mm, and that's probably harder than would be ideal so I will need to do a little more filing of slots because some of the keys don't quite travel as far as I'd like.

An unexpected side effect is that the "clack" on button release is reduced, since the pallets haven't lifted so high.

Question for Theo, if you wouldn't mind ... how far do the pallets need to lift to play properly?   

Thanks again.

Logged
Tony S

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pokerwork clacking
« Reply #49 on: September 25, 2009, 08:44:30 AM »

Question for Theo, if you wouldn't mind ... how far do the pallets need to lift to play properly?   


Not as far as you might think.  4mm to 5mm of button travel is usually ok, you may be able to use less.  If the pallets don't open far enough the note will eventually be reduced in volume, end even go flat. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Scallyanglo

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 106
  • Baffetti/Oakwood Binci Pariselle 2.6 LM 14 bass
Re: Pokerwork clacking
« Reply #50 on: January 04, 2010, 01:59:32 PM »

I am attempting the standard 'Theo fix' as demonstrated by the facebook photos. However, is there is a difference between the Erica shown and my pokerwork? The gap between case and the lowest part of the levers is closer to 5mm i.e. the levers have square-bottomed (or 'u'-shaped) bent parts that are lower than the levers themselves.

If I've done this right - here's a link to a photo which hopefully explains what I mean!
http://cid-cd8bb8c1128a63f5.skydrive.live.com/self.aspx/Everyone/jse%5E_Pokerwork%5E_treble%5E_levers.jpg

My question - does the softwood go under the lowest part of the lever, or just the extended bit that holds the button?
Cheers, K.
Logged

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Pokerwork clacking
« Reply #51 on: January 04, 2010, 02:46:42 PM »

If I understand you correctly, you're refering to the square bend just at the pivot point, right? I don't think that you could pad the travel there in any truly effective way, given the tiny amount of travel at that point, vs. the leverage you have way out there at the button end.

I installed hard felt padding at the points just beneath the buttons, so the stopping effect is quite immediate and precise.

Hope I'm explaining this in an understandable way!

Bob
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pokerwork clacking
« Reply #52 on: January 04, 2010, 04:47:33 PM »

My question - does the softwood go under the lowest part of the lever, or just the extended bit that holds the button?
Cheers, K.

I usually position the softwood strip as far near the edge of the box as possible, but ensuring I leave sufficient space for the edge of the fingerboard to fit.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Scallyanglo

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 106
  • Baffetti/Oakwood Binci Pariselle 2.6 LM 14 bass
Re: Pokerwork clacking
« Reply #53 on: January 04, 2010, 06:14:31 PM »


By the way, does anyone know how much a replacement fingerboard costs?  Just the ordinary black plastic one on the Pokerwork?

£21.99

Does this include a replacement for those flippin' awful M3 screws used in the Chinese boxes? I think I've got the wood placed correctly, and wanted to try it out before permanently fixing. However, it's really difficult to fasten the fingerboard back on, as the screwheads are not a good fit for any of my Phillips screwdrivers, and are now getting quite damaged >:( I've been out looking for alternate screws to fit, but nothing seems to match. All ideas welcome!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pokerwork clacking
« Reply #54 on: January 04, 2010, 11:22:19 PM »

No it does not include the screws.   I have replacement screws if you need them.  They are an improvement on the Chinese ones that Hohner use, but you still have to be very careful putting them in to align them with the holes in the fingerboard which are not at right angles to the end of the box.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Scallyanglo

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 106
  • Baffetti/Oakwood Binci Pariselle 2.6 LM 14 bass
Re: Pokerwork clacking
« Reply #55 on: January 05, 2010, 12:38:51 AM »

No it does not include the screws.   I have replacement screws if you need them.  They are an improvement on the Chinese ones that Hohner use, but you still have to be very careful putting them in to align them with the holes in the fingerboard which are not at right angles to the end of the box.

Yes! The screw holes are not at right angles and I hadn't noticed before. I now have one fine pokerwork without disappearing buttons that still has a great clacky sound. ;) Ta very much to all for the advice.
« Last Edit: January 05, 2010, 12:41:09 AM by Scallyanglo »
Logged

John C

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 124
Re: Pokerwork clacking
« Reply #56 on: January 07, 2010, 12:20:41 AM »

I've re-read this thread but I cannot see what you are using to glue(?) the small strip of wood under the levers to reduce buttons sinking into the holes.   Can you please clarify that for me.

Thanks
John
Logged
Saltarelle Laurentide GCF, Saltarelle Cheviot ADG

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Pokerwork clacking
« Reply #57 on: January 07, 2010, 07:20:55 AM »

I've re-read this thread but I cannot see what you are using to glue(?) the small strip of wood under the levers to reduce buttons sinking into the holes.   Can you please clarify that for me.
According to Theo's photo presentation here....
http://www.facebook.com/album.php?aid=109685&id=709188166&l=c564b24e38
.... he does not use glue, but the strip of wood is screwed into place lightly, just enough to stop it moving. See photos 8, 9 and 10, and read the captions.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

John C

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 124
Re: Pokerwork clacking
« Reply #58 on: January 07, 2010, 01:47:05 PM »

I did read the caption but I assumed the screws were temporary to hold the wood in place so you could mark the place for the indents.   

I had thought that after cutting the grooves and being satfisfied with the fit, the wood needed to be held in position and it looked like the screws were too big.   I don't want to damage the box itself and was thinking about gluing the piece in place but I realize that would make it difficult to remove the piece afterward, if it was necessary.



Logged
Saltarelle Laurentide GCF, Saltarelle Cheviot ADG

Bill the Farmer

  • Not quite so
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 497
  • Hohner Club, Liliput...
    • Bill Farmer
Re: Pokerwork clacking
« Reply #59 on: January 07, 2010, 02:22:00 PM »

I used a small smear of Bostic each end to hold the wood on my 1140. It dries into clear rubbery stuff, so should come off reasonably easily if necessary (He hopes  ;D).  :||:
Logged
Bill of Old Radipole Village
Pages: 1 2 [3] 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal