Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Soldering Iron For Reed Waxing  (Read 4605 times)

0 Members and 1 Guest are viewing this topic.

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Soldering Iron For Reed Waxing
« on: January 23, 2020, 11:31:27 PM »

I've been looking at temperature controlled soldering irons with a view to using one to wax reeds in. I'm happy enough using a waxing spoon to do a whole set of reeds but now and again I find it necessary to dig a reed plate off the block when there's a problem with the inside reed and it's a bit of a faff setting things up and melting a panfull of wax just to refit one plate. Prices for soldering stations vary enormously, and whilst I never begrudge spending money on decent kit I'd rather not spend more than I have to on something that will only get ocassional use.

Not all makers state a temperature range for thier irons, but those who do seem to have 90 degrees C as the minimum temperature. Is this okay to melt accordion wax using direct contact without overheating it? Any advice would be greatly appreciated.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Soldering Iron For Reed Waxing
« Reply #1 on: January 23, 2020, 11:39:40 PM »

I use one of THESE connected to a standard lamp dimmer. Seems to work fine.

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Soldering Iron For Reed Waxing
« Reply #2 on: January 24, 2020, 12:19:05 AM »

A bit like Lester.  Very ordinary 40w (I think - could be less) Weller soldering iron hooked up to a 600w (rated) light dimmer.  Dimmer setting is the key, not terribly critical: it's fairly easy to find 'hot enough' setting that will melt wax with minimal smoking.
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Soldering Iron For Reed Waxing
« Reply #3 on: January 24, 2020, 07:44:57 AM »

Ditto, simple soldering iron similar to Lester's. I have a dimmer socket, otherwise the same.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Soldering Iron For Reed Waxing
« Reply #4 on: January 24, 2020, 08:10:27 AM »

A temperature controlled iron is much better.  It reduces power when the iron is idle,  and increases it as you use more heat to melt wax.  A dimmer switch is better than nothing,  but the iron will still be hotter than ideal when you take it from it’s stand and will cool down as you melt more wax. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
« Last Edit: January 24, 2020, 01:46:05 PM by John MacKenzie (Cugiok) »
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Soldering Iron For Reed Waxing
« Reply #6 on: January 24, 2020, 01:44:58 PM »

Logged
C#/D player

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Soldering Iron For Reed Waxing
« Reply #7 on: January 24, 2020, 03:36:58 PM »

Thanks for all of the helpful replies, I'm going to get a temperature controlled iron rather than use a dimmer but haven't quite decided which one yet.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Soldering Iron For Reed Waxing
« Reply #8 on: January 24, 2020, 04:32:58 PM »

Thanks for all of the helpful replies, I'm going to get a temperature controlled iron rather than use a dimmer but haven't quite decided which one yet.


The likes of the iron John recommended upthread is not temperature controlled but just a better packaged dimmer switch

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Soldering Iron For Reed Waxing
« Reply #9 on: January 24, 2020, 05:00:58 PM »

Thanks Lester, I'd more or less worked that out from the price, even a simmerstat costs more than that! I'm going to wait until my birthday and have a decent iron at the top of my wish list, it'll be good for adding solder to reed tips too.  ;D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Soldering Iron For Reed Waxing
« Reply #10 on: January 24, 2020, 05:56:11 PM »

I have a temperature-controlled soldering iron with a digital temperature display, bought from Maplin before they went bust.
It's similar to this one.

It does reed waxing very nicely.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Soldering Iron For Reed Waxing
« Reply #11 on: January 25, 2020, 05:21:08 PM »

I use both in my shop. I have modified irons that I make and both work well.
The temp controlled one is usually used for large jobs otherwise the iron can cool down while working ,but it's big advantage is that it does not smoke while sitting.
 the lamp dimmer one works well and you can crank up the heat a bit if you are doing a bigger job ,it does smoke a lot less than a un dimmed one.
 I sell the regular iron in eBay , the tip is hammered out and has a brass blade soldered to it with high temp solder for good heat transfer and the blade is riveted to the iron with brass rivets. https://www.ebay.com/itm/193282388610?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Patrick mc cune

  • Member
  • *
  • Offline Offline
  • Posts: 4
Re: Soldering Iron For Reed Waxing
« Reply #12 on: January 30, 2020, 05:39:52 AM »

Thanks for all of the helpful replies, I'm going to get a temperature controlled iron rather than use a dimmer but haven't quite decided which one yet.
  i just bought a dimmer on ebay , 14.00 , works just fine . No smoke on a  1/4 turn.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Logged
C#/D player

Winston Smith

  • Hero Member
  • *****
  • Online Online
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Soldering Iron For Reed Waxing
« Reply #14 on: October 27, 2021, 11:47:27 AM »

"would this one be an example of the former?"

That's a nice looking bit of kit, but I'd rather buy a melodeon for that much, and just struggle on with my old "Remploy" iron!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Soldering Iron For Reed Waxing
« Reply #15 on: October 27, 2021, 12:34:24 PM »

"would this one be an example of the former?"

That's a nice looking bit of kit, but I'd rather buy a melodeon for that much, and just struggle on with my old "Remploy" iron!

I’m not sure what price you’re seeing, but for a soldering iron station that would be considered rather inexpensive;  a quality unit would certainly cost more…and whatever melodeon you would get for that price would be absolute rubbish!
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Soldering Iron For Reed Waxing
« Reply #16 on: October 27, 2021, 01:42:39 PM »

It also comes down to the scope of what you're doing.  I overhauled and re-waxed nearly 700 reeds in the last week alone, so I have no wish to 'struggle' along and get by with cheap equipment!  I'm actually going to be investing in a proper wax pot and spoon setup for doing bigger waxing jobs, but I'd still like to have a decent temperature-controlled soldering iron on hand for when it's needed.  The reason I'm asking is that I was under the impression the soldering iron I had was temperature-controlled (seeing as it had a knob on the front and a temperature range from 150 C to 450 C) but it turns out it's actually a variable power control.  The temperature of the tip keeps changing as I wax - it will be quite hot when it's been sitting for a bit, but will cool down (and slow down the process) after melting wax for a while.  As I understand it, a proper temperature-controlled unit will help to avoid this.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Soldering Iron For Reed Waxing
« Reply #17 on: October 27, 2021, 02:41:06 PM »

Yes you do need a soldering iron with true temperature control.  A dimmer switch or your old type are ok for occasional use,  but not for large scale use.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Marriott

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1048
Re: Soldering Iron For Reed Waxing
« Reply #18 on: October 27, 2021, 03:19:55 PM »

"would this one be an example of the former?"

That's a nice looking bit of kit, but I'd rather buy a melodeon for that much, and just struggle on with my old "Remploy" iron!

Wouldn't get much of a melodeon for less than fifty quid!
Logged
Chris

Castagnari Mory, English Concertina and Piano Accordion.

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Soldering Iron For Reed Waxing
« Reply #19 on: October 27, 2021, 04:13:41 PM »

There are iron's designed for wax ? I use one for some jobs & they do not get too hot, but do get hot enough.  Mine is a bit older than the one below but the unit is the same and the tips similar.  They suit the 'wax pencil/stick' method of delivery....

https://thecraftstore.com/product/45073/encaustic-art-stylus-pro-dual-heat-graphics-tool-with-3-tips/987208?gclid=Cj0KCQjw8eOLBhC1ARIsAOzx5cEIObvFNno4LZpLTDuPiLpQBXNUMtUZVU64TZrxLNQMbbKmljPRfDoaAtOkEALw_wcB
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal