Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Removing the fingerboard on A Dino BP III  (Read 1267 times)

0 Members and 1 Guest are viewing this topic.

Adam Smith

  • Member
  • *
  • Offline Offline
  • Posts: 15
Removing the fingerboard on A Dino BP III
« on: February 22, 2020, 01:14:20 PM »

Hello all,

Apologies if this is already here somewhere, my searches produced nothing.

I am trying to work out how to get the fingerboard surround off of my Dino Black Pearl III. I need to access the keys so as to clean off the horrible black Sharpie some *** has coloured them in with and also repair a wood chip. I've managed to take it off of the pearloid tops with acetate but it's all over and looks terrible.

It isn't like any of the Hohners I've had apart in the past with two screws inside the treble reed housing. I do see a pin peeking out of the side of the box but am.loathe to remove it without knowing that that is the correct course of action.

Many thanks,

Adam.
Logged
Serenellini Gold 98 D/G : Hohner Erica D/G : Hohner 1040 C : Jozef Ježrnik Steirische Harmonika G/C/F : Antonin Hlaváček Heligonka D/G : Hohner Liliput C/F : Hohner Liliput D/G :

OBJ Morris

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Removing the fingerboard on A Dino BP III
« Reply #1 on: February 22, 2020, 01:31:07 PM »

Could that pin be the end of the axle?
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Removing the fingerboard on A Dino BP III
« Reply #2 on: February 22, 2020, 01:45:57 PM »

Yep, just pull the pin out and the keyboard will do the same as a grenade does when you pull out the pin.
But in all seriousness this is what I do

0) Remove the grill
1) Make little masking tape labels to label the buttons, all the keys are different and need to go back where they came from
2) Grasp the end of the axle and twist/pull, it will be very hard to move as it has 21 sprung axles bearing on it.
3) As the axle withdraws catch the mechanisms as they are freed
4) Do whatever yo want to do to the mechs
5) Insert the axle and then (this is the really hard bit) reinsert arm No.21 and align the axle and the arm pivot hole and push in the axle. This gets increasingly difficult as the number of arms increases, I have found that attaching an electric variable speed drill to the axle makes reinserting it easier. MAKE REALLY SURE that the hole and the axle are aligned before using any force/rotation as you can damage the arms.
6) Try to decide whether this was all worthwhile.


If that has not put you off the story from Rees Wesson who on finding a jammed axle had to connect a car battery across it until smoke poured out of the mechanism to get the axle to free up may also help.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Removing the fingerboard on A Dino BP III
« Reply #3 on: February 22, 2020, 07:37:18 PM »

Jumpleads, yeah!

Point 3 in Lester's list.
Fit an elastic band over the keyboard to stop the levers jumping out - it frees up a spare hand.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Adam Smith

  • Member
  • *
  • Offline Offline
  • Posts: 15
Re: Removing the fingerboard on A Dino BP III
« Reply #4 on: February 22, 2020, 08:47:32 PM »

Thank you all! I shall see if I can get it off without removal for now, but I may attempt it if it bugs me enough.
Logged
Serenellini Gold 98 D/G : Hohner Erica D/G : Hohner 1040 C : Jozef Ježrnik Steirische Harmonika G/C/F : Antonin Hlaváček Heligonka D/G : Hohner Liliput C/F : Hohner Liliput D/G :

OBJ Morris

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Removing the fingerboard on A Dino BP III
« Reply #5 on: February 26, 2020, 12:15:11 PM »

Just a thought, but having had to sort out two of these which suffered from sticking keys, if you do have to pull the axle I would take the opportunity to replace it with an accurately dimensioned
stainless axle.
The original axle in each was ferrous metal, with rust spots and pits which were binding in the keys.

Graham
Logged

Adam Smith

  • Member
  • *
  • Offline Offline
  • Posts: 15
Re: Removing the fingerboard on A Dino BP III
« Reply #6 on: February 26, 2020, 07:58:19 PM »

Good idea. Do you know what gauge wire that would be?
Logged
Serenellini Gold 98 D/G : Hohner Erica D/G : Hohner 1040 C : Jozef Ježrnik Steirische Harmonika G/C/F : Antonin Hlaváček Heligonka D/G : Hohner Liliput C/F : Hohner Liliput D/G :

OBJ Morris
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal