Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: wax to screw conversion  (Read 706 times)

0 Members and 1 Guest are viewing this topic.

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
wax to screw conversion
« on: March 12, 2020, 03:38:08 PM »

After manufacturing and fitting a 3rds removal stop to my old and little used Hohner Club Modell 2 C/F, I decided to clean up the reeds, re-valve them, and convert the block from wax to screw fixing, using gaskets laser cut from Olivisc.
The problem of course, is that the aperture on the block extends right down to the base plate and is normally filled with wax. A gasket requires a solid seat, so rather than cut endless little bits of wood and gluing them in, or cram the reed plate down onto a 90 degree strip if gasket, I adopted a different approach.
Firstly, I sanded the two faces of the block, taking off 1mm or so. I then, from 1mm aircraft ply, made two facings, one for each side, which include the bottom bit missing from the block, (see the pictures). Empirical experiment showed me that there is enough room left for the reed and valve to function with the aperture effectively reduced in size. Having glued on the facings and sanded down to neaten and clean everything, I gave it all a coat of Danish oil. This does not, as some will venture, compromise the  gaskets adhesion, but rather having dried, it allows just the necessary level of adhesion, allowing pulling off and re-positioning if needed.
Finally, put all the screws in ready for the cleaned reeds. Job done! I may even play it some time.
Has anyone else used this method? Did it work OK? Any comments or suggestions for a better way?
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: wax to screw conversion
« Reply #1 on: March 12, 2020, 04:01:43 PM »

Excellent! You have made a fine job of that. Well done!

If there was any noticeable restriction in air flow which might compromise the reeds' performance, it looks as if you have enough widthways room to enlarge the air vents sideways a little bit, so long as the holes are still covered by the pallets when in the closed poition. But as you say, that may well not be necessary.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: wax to screw conversion
« Reply #2 on: March 12, 2020, 04:27:00 PM »

Cheers Steve. Yes, I was a little worried about the effect of even a small reduction in air-flow. Time will tell. The "squaring" of the round holes I had to do to make the 3rds removal slide work worries me a little too, but again time will tell. I suspect that it's major effect will be on the tuning, but as I am going to re-tune anyway, that should not be a problem.
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: wax to screw conversion
« Reply #3 on: March 12, 2020, 05:41:48 PM »

Normal practice is to run a strip of Olovisc along the baseplate and butt the reed-plate up to it.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: wax to screw conversion
« Reply #4 on: March 12, 2020, 07:01:45 PM »

Yes Rees, I have done that a couple of times and it worked, but it just seems mechanically not the best solution. However - if it works it works. D
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal