Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Big/low Bass reeds  (Read 782 times)

0 Members and 1 Guest are viewing this topic.

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Big/low Bass reeds
« on: June 25, 2020, 12:52:51 PM »

I am still working on my 16 bass 1900 Italian box.  The heat is making it feel at home.

The 'low' 8 reeds are on big plates, narrow reed tongues and +/-, 2.5" long. 

They share a block with standard size, more typical bass reeds which are fairly straight forwards to get to sound and speak pretty quickly at their requisite pitch.  In sharing their block - unlike a Hohner, say -,they have a double row of Fondo holes rather than a large shared one, so they have independent 'air' as such. 

At what point in the 'draw'/push, on the tuning table, should these big/low reed's reach (tuning) pitch ?  Being so long/big, they inevitably start short - arrive - and are inclined to go past.  The biggest are slowest, so I assume there is a balance to be struck.

In simple terms ( the less numbers involved the better ) where in the 'flow' should I be aiming to see the +/-  :D appear on my Tuner. 

I am guessing there are three potential options ? As soon as possible - on the basis that by the time they start to go sharp I will have moved on.....ending there, irrespective of the flat start......or mid-flow, allowing for variance in playing and the best ( and worst ) of all worlds.

cheers, N

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Big/low Bass reeds
« Reply #1 on: June 25, 2020, 01:02:10 PM »

First think to check is that your tuning setup provides a generous volume of air through the reeds and is not restricted by holes smaller than those in the reed blocks.

After that it depends what sounds best when it plays with it's other higher octave reeds.  The presence of the other reeds will actually help the bass reed to speak sooner.   You can also take into consideration how the player will use it.   If it's short staccato bass then you need to get the right pitch early, if it's long held basses or even drones that you may want to work at the eventual stable pitch.  Once you have those ideas on board then its a matter of the best compromise.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Big/low Bass reeds
« Reply #2 on: June 25, 2020, 04:22:27 PM »

Quote
The presence of the other reeds will actually help the bass reed to speak sooner.

Silly question maybe, but is this true even in Nigel's box where the reeds have "independent air", as he says ?? (would the helful coupling take place mechanically or 'pneumatically' ?) 
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Big/low Bass reeds
« Reply #3 on: June 25, 2020, 06:22:41 PM »

Thanks Theo.  My 'table' is set up with Hohner spec, single 'bass' sized, chord sized and treble x1 & x2 holes......none of which quite replicate the hole for the bass reeds in this old Italian block.  Now resolved, I'll have another go.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal