Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Servo assisted Hot-rod Hohner  (Read 876 times)

0 Members and 1 Guest are viewing this topic.

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Servo assisted Hot-rod Hohner
« on: November 24, 2020, 08:12:45 PM »

I have just done the Lester Hot-rod work on a Hohner/Koch G/C and, having developed a taste for servo screws, opted to use them for the reeds rather than wax.  Olovisc on the blocks, 2.2 x 11mm hex-drive Servo screws, from a R/C Model outlet on-line, 2mm drill & 2mm Hex drive insert in a magnetic holder.

I re-tuned using Steve_Freerider's tuning guide to his Mory 'standard'.  The use of the 'dry' fitting allowed for a very fine tuning by virtue of thumb pressure fitting/re-fitting until the fettling was done as opposed to having to do finishing work on the reeds after waxing, which I always find a messy job.   

The Servo screws have a built in washer head which works well to nip the reed to the gasket.  Learning from the 1930's Boxes I have just worked on to de-club/tune, I fitted a small trim to the base of the blocks and lined it with a strip of quality leather to seal the bottom edge of the reed plate.

I think I am a convert.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Servo assisted Hot-rod Hohner
« Reply #1 on: November 24, 2020, 08:38:49 PM »

I admit my first thought when I saw "Servo assisted" had me thinking "Don't Hohners produce enough  mechanical noise for this bloke?"

Nice idea - a bit puzzled by just one screw at the head of the reed plate rather than a screw between the reed plates half way done so that each plate be screwed down on two sides. What holds the feet of the reed plates to the seals?
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Servo assisted Hot-rod Hohner
« Reply #2 on: November 24, 2020, 09:01:37 PM »

In the first image, you can see the thin ply strip with an '/' profile which, in turn, has a strip of valve leather laid against it.  This replicates the fitting method of the 1930's Nussbaumer/Socin's I have.  The bottom edge of the reed sits on the leather and the '/' profile effects the "pinch".

Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Servo assisted Hot-rod Hohner
« Reply #3 on: December 03, 2020, 12:58:27 PM »

I have refinished the worn tape etc on the Koch/Hohner, so I now have a decent G/C box.  Some inspiration take from a Fraton listing and a coincidental find of some appropriate leather.  I didn't extend to the inner paper on the bellows themselves, as it wasn't necessary.

Logged

Kon

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 165
Re: Servo assisted Hot-rod Hohner
« Reply #4 on: December 03, 2020, 05:05:13 PM »

Very pretty!
Logged
GC Erica
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal