Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Converted my "toy accordion" melodeon to single voice; next steps?  (Read 6389 times)

0 Members and 1 Guest are viewing this topic.

TapTheForwardAssist

  • Member
  • *
  • Offline Offline
  • Posts: 45

I recently bought an "Eastar" brand toy accordion on Amazon in the US, for US$45.

It's a pretty standard "Chanson" as y'all call it here, 7-button diatonic with left-hand base and chord buttons. Notably, it's all plastic body, no wood in the fingerboard or whatever, and melody reedback is a solid plastic piece.

I had some "learning by doing" in terms of figuring out the best way to silence the extra reed in each double-reeded note, and had to play around because in some cases the push reed closest to in-tune was on a different channel from the pull reed that was closest. Also I learned the hard way that I should put the tape on the base of the reedlbock itself, not over the holes leading to the action, since the tape really loves to stick to the padding and is hard to remove without tearing it. So at this point I have a cheapie box that's decently in tune with itself. So my remaining questions:

  • I have one reed that just doesn't want to voice. Do I slide thin paper under it to clear fluff out? "Sproing" it gently to knock loose any dust?
  • The rubbery padding the reedblock sits on is kinda loose, glue it down?
  • Any other ways, at least on the treble end, to check for any gaps where it might be losing air?
  • On the bass side, best way to "de-third" the chords?
  • I've seen mention of improving action by limiting key travel beyond what's necessary. There's a plate under the fingerboard that would give access to the keys, so do I just drop that plate and put in a thin line of foam or cardboard or whatever and see if the keys with shortened travel still lift the pallets enough for the note to sound
  • Is there anything to be done about how noisy/crackly the bellows are? Do they get better as they get played in? Flying Duck Concertinas has been make "origami" paper bellows, might contact them to see if the same idea can be transferred to a Toy Accordion to remove the lame bellows from the equation
  • Any other ways to make this decently playable? It's already substantially better just from my initial steps. I know it won't ever be a Hohner, but it's been pretty fun already thus far, and I'm working up some tutorial videos on how to modify it as I learn by doing and from advice gleaned from this forum

Thanks for any pointers!
« Last Edit: February 11, 2021, 03:08:05 PM by TapTheForwardAssist »
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #1 on: February 11, 2021, 08:22:42 AM »

I recently bought an "Eastar" brand toy accordion on Amazon in the US, for US$45.

It's a pretty standard "Chanson" as y'all call it here, 7-button diatonic with left-hand base and chord buttons. Notably, it's all plastic body, no wood in the fingerboard or whatever, and melody reedback is a solid plastic piece.

I had some "learning by doing" in terms of figuring out the best way to silence the extra reed in each double-reeded note, and had to play around because in some cases the push reed closest to in-tune was on a different channel from the pull reed that was closest. Also I learned the hard way that I should put the tape on the base of the reedlbock itself, not over the holes leading to the action, since the tape really loves to stick to the padding and is hard to remove without tearing it. So at this point I have a cheapie box that's decently in tune with itself. So my remaining questions:

  • I have one reed that just doesn't want to voice. Do I slid thin paper under it to clear fluff out? "Sproing" it gently to knock loose any dust?
  • The rubbery padding the reedblock sits on is kinda loose, glue it down?
  • Any other ways, at least on the treble end, to check for any gaps where it might be losing air?
  • On the bass side, best way to "de-third" the chords?
  • I've seen mention of improving action by limiting key travel beyond what's necessary. There's a plate under the fingerboard that would give access to the keys, so do I just drop that plate and put in a thin line of foam or cardboard or whatever and see if the keys with shortened travel still lift the pallets enough for the note to sound
  • Is there anything to be done about how noisy/crackly the bellows are? Do they get better as they get played in? Flying Duck Concertinas has been make "origami" paper bellows, might contact them to see if the same idea can be transferred to a Toy Accordion to remove the lame bellows from the equation
  • Any other ways to make this decently playable? It's already substantially better just from my initial steps. I know it won't ever be a Hohner, but it's been pretty fun already thus far, and I'm working up some tutorial videos on how to modify it as I learn by doing and from advice gleaned from this forum

Thanks for any pointers!
Why are you wnting to limit button travel?
Unless your "Eastar" is a completely different model to the recent wood bodied Chanson's the buttons bottom out without disappearing down the the keyholes any way.
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #2 on: February 11, 2021, 10:35:23 AM »

I have one reed that just doesn't want to voice. Do I slid thin paper under it to clear fluff out? "Sproing" it gently to knock loose any dust?
That should do it - one or the other of those methods.
Quote
Any other ways, at least on the treble end, to check for any gaps where it might be losing air?
Those things lose a fair amount of air through the bellows. Also check the pallets, perhaps?
Quote
On the bass side, best way to "de-third" the chords?
I'm pretty sure mine doesn't have thirds anyway.
Quote
Is there anything to be done about how noisy/crackly the bellows are? Do they get better as they get played in? Flying Duck Concertinas has been make "origami" paper bellows, might contact them to see if the same idea can be transferred to a Toy Accordion to remove the lame bellows from the equation
They'll probably get leakier as they get played in... yes, replacing the bellows might well improve things.
Quote
Any other ways to make this decently playable?
From what I've read, blocking one reed of each pair (which you've already done) to reduce air usage is one of the best treatments.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #3 on: February 11, 2021, 10:59:01 AM »


    • Any other ways to make this decently playable? It's already substantially better just from my initial steps. I know it won't ever be a Hohner, but it's been pretty fun already thus far, and I'm working up some tutorial videos on how to modify it as I learn by doing and from advice gleaned from this forum


    If your serious about playing melodeon, you could throw it out and buy a Geordie. Great little instruments. Couldn't believe it, the first time I met one in the flesh.

    https://www.acorninstruments.co.uk/listing.cfm?inst=1[/list]
    « Last Edit: February 11, 2021, 11:01:24 AM by Tone Dumb Greg »
    Logged
    Greg Smith
    DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

    ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

    Theo

    • Administrator
    • Hero Member
    • *****
    • Offline Offline
    • Posts: 14475
    • Hohner Club Too
      • The Box Place
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #4 on: February 11, 2021, 11:28:15 AM »


    Quote
    Is there anything to be done about how noisy/crackly the bellows are? Do they get better as they get played in? Flying Duck Concertinas has been make "origami" paper bellows, might contact them to see if the same idea can be transferred to a Toy Accordion to remove the lame bellows from the equation
    They'll probably get leakier as they get played in... yes, replacing the bellows might well improve things.

    You can replace the reeds with better quality ones.  I've heard of people doing that.  Will give you a quicker response, and probably a bit louder.

    Once you've replace the reeds and bellows then you only have the mechanism to worry about. When I messed about with one of these I found that the treble levers would bend quite easily. 

    Logged
    Theo Gibb - Gateshead UK

    Proprietor of The Box Place for melodeon and concertina sales and service.
    See my YouTube channel  for videos on repair and tuning

    Tiposx

    • Durham in England
    • Respected Sage
    • ****
    • Offline Offline
    • Posts: 259
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #5 on: February 11, 2021, 11:46:00 AM »

    I have fitted conventional melodeon reed plates to give D and G (both Horner and Cagnoni) into four of these plastic bodied instruments. They are single voiced with accidentals instead of chords on the left hand buttons. I fitted a separate air lever assembly into one, which freed up the third l/h button for a third accidental button. They are all second button start.
    I find that most of the air leaks through the standard air button, which doesn’t fit or seal in any plane I can think of. The pads need re-surfacing also. It is easy to re- surface or replace the air button with something that works. I found that the bellows weren’t actually leaking vey much. A few dabs of pva into where the gussets join the folds sorted any minor leaks out.
    The leaky pads and air button affect things more on the push than the draw, so for instance the G tuning with accidentals works very well on tunes in D.
    The new reeds are much louder than the originals, and the creaking of the bellows doesn’t seem to matter as much as a result. There was room for two voices in the G using Hohner reeds on the original reed block, but I didn’t fit them as it was loud enough for the pub sessions with one voice.
    The buttons can stick under the keyboard, but the fix is to straighten the aluminium mechanism out so that the buttons move without contacting the sides of the holes. Also the holes may need a little sanding at the narrow points. White plastic dust from the buttons will show where the sanding needs to be done.
    Also I fitted proper strap brackets with nuts and bolts instead of screws.
    I can’t recall all the the improvements, but they can be pretty quick players. The plastic tone doesn’t go away though, even with a wooden fondo  fitted. That is why I moved on , I didn’t really care for the tone.
    Logged

    Tiposx

    • Durham in England
    • Respected Sage
    • ****
    • Offline Offline
    • Posts: 259
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #6 on: February 11, 2021, 11:50:14 AM »

    Look up “Toy melodeon mods” in this forum, I posted some details and photos. That was a D version with Cagnoni reeds, which later I converted to flat mounted reeds for more volume.

    The Hohner G reeds fitted onto the original reed black and you can fit two voices if you really want to...
    « Last Edit: February 11, 2021, 12:00:06 PM by Tiposx »
    Logged

    TapTheForwardAssist

    • Member
    • *
    • Offline Offline
    • Posts: 45
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #7 on: February 11, 2021, 02:56:30 PM »

    If your serious about playing melodeon, you could throw it out and buy a Geordie. Great little instruments. Couldn't believe it, the first time I met one in the flesh.

    I appreciate, but I do already own a properly-fettled HA-112, and a Toy re-reeded to D by Michael Usui, and previously owned a C#/D Erica.

    I bought this Eastar because I want to learn how to improve them and make a YouTube tutorial showing how to do so, so that more people who would never budget for even a US$300 used Hohner 1-row might be willing to drop US$45 on a toy and clean it up to just feel out the instrument.

    At US$965, the Geordie I'm sure is lovely but in a completely different category at 21x the price. I will note though that I did write the Angelo Piccoli shop to get a quote on a similar model of "organetto": http://www.angelopiccoli.com/shop/en/legno/8-mini-eco-i.html

    It seems Piccoli is filling the "tiny Italian diatonic" niche that Giustozzi formerly filled.
    « Last Edit: February 11, 2021, 03:02:53 PM by TapTheForwardAssist »
    Logged

    TapTheForwardAssist

    • Member
    • *
    • Offline Offline
    • Posts: 45
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #8 on: February 11, 2021, 02:57:34 PM »

    Why are you wnting to limit button travel?
    Unless your "Eastar" is a completely different model to the recent wood bodied Chanson's the buttons bottom out without disappearing down the the keyholes any way.

    It seemed a few folks mentioned limiting the action in some past threads on the Chansons here, and iirc one of the makers who converts/ed these to better reeds mentioned limiting button travel for speed.
    Logged

    TapTheForwardAssist

    • Member
    • *
    • Offline Offline
    • Posts: 45
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #9 on: February 11, 2021, 03:01:06 PM »

    You can replace the reeds with better quality ones.  I've heard of people doing that.  Will give you a quicker response, and probably a bit louder.

    Yes, I've owned several re-reeded Toys by Michael Usui (not sure if he still offers that), and I know Smythe does a similar job but on higher-quality Russian toys.

    So far as replacing the reeds though, my understanding is that some folks replace the whole reedblock to fit larger reeds, which is beyond my skill level, though I wouldn't be opposed to trying it with any reeds of the right size to "drop in" to the current reedblock.

    Quote
    Once you've replace the reeds and bellows then you only have the mechanism to worry about. When I messed about with one of these I found that the treble levers would bend quite easily.

    The one where the levers bent on you, was it the kind with the exposed stamped-metal levers (Cajun-esque), or with concealed levers like is more common currently? My first toy melodeon in the 1990s was a Hero and had the exposed levers, but when I first got a re-reed from Michael he was quite firm on my getting one with internal levers, due to the bending risk of the exposed ones.
    Logged

    TapTheForwardAssist

    • Member
    • *
    • Offline Offline
    • Posts: 45
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #10 on: February 11, 2021, 03:03:29 PM »

    The Hohner G reeds fitted onto the original reed black and you can fit two voices if you really want to...

    Were the Hohner G reeds the octave above the stock C pitch, or the octave below that C?
    Logged

    TapTheForwardAssist

    • Member
    • *
    • Offline Offline
    • Posts: 45
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #11 on: February 11, 2021, 03:07:42 PM »

    I have fitted conventional melodeon reed plates to give D and G (both Horner and Cagnoni) into four of these plastic bodied instruments. They are single voiced with accidentals instead of chords on the left hand buttons. I fitted a separate air lever assembly into one, which freed up the third l/h button for a third accidental button. They are all second button start.

    Quote
    I find that most of the air leaks through the standard air button, which doesn’t fit or seal in any plane I can think of. The pads need re-surfacing also. It is easy to re- surface or replace the air button with something that works. I found that the bellows weren’t actually leaking vey much. A few dabs of pva into where the gussets join the folds sorted any minor leaks out.

    This is dynamite insight, thanks! I'll check the air button pad to see if that's the issue first, and then start considering the other pads. Do you have a recommended material for re-facing pads on these? Anything accessible and affordable?


    Quote
    The buttons can stick under the keyboard, but the fix is to straighten the aluminium mechanism out so that the buttons move without contacting the sides of the holes. Also the holes may need a little sanding at the narrow points. White plastic dust from the buttons will show where the sanding needs to be done.

    Again, awesome insight, I would never have thought of this on my own without months of discovery!


    Quote
    Also I fitted proper strap brackets with nuts and bolts instead of screws.

    Yup, had this on my professional re-reed, so I could use a one-shoulder strap.. Though I will say the Eastar has nicer "leather" on the left-hand strap and right thumb-strap than any of the 20+ toys I've previously handled.


    Quote
    I can’t recall all the the improvements, but they can be pretty quick players. The plastic tone doesn’t go away though, even with a wooden fondo  fitted. That is why I moved on , I didn’t really care for the tone.

    My Usui models have been surprisingly decent players (even in my amateur hands) compared to the stock; night and day difference.

    Thanks so much for the detailed post of brilliant fixes!
    Logged

    Theo

    • Administrator
    • Hero Member
    • *****
    • Offline Offline
    • Posts: 14475
    • Hohner Club Too
      • The Box Place
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #12 on: February 11, 2021, 03:30:42 PM »

    Yes the bent levers I had were the external type.

    The cheapest way to get better reeds is to harvest some from an old PA and retune them.  It does require some time and skill, but the skill is something that you could acquire with a little practice.  That I turn will open up other possibilities for reed work.
    Logged
    Theo Gibb - Gateshead UK

    Proprietor of The Box Place for melodeon and concertina sales and service.
    See my YouTube channel  for videos on repair and tuning

    Tiposx

    • Durham in England
    • Respected Sage
    • ****
    • Offline Offline
    • Posts: 259
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #13 on: February 11, 2021, 06:03:01 PM »

    When I ordered the G reeds from Charlie Marshall I gave him the approx dimensions and that I wanted to cover  buttons 2 to 8 of the G row on a DG melodeon (if I remember right) They just happened to fit almost perfectly.
    I used my own pallet facing material, made of felt and leather, as is normal on melodeons. I used thin double-sided tape to fix the felt to the plastic pallets, (also normal for me). The main thing is to get the right thickness so that the pallets close correctly. I reattached the pallets with hot glue or wax,  once everything had settled down.
    I still have two of these boxes, so I can check anything else on the build if needed.
    Oh and the buttons are floppy on the levers. - I aligned mine properly and then fixed them securely with hot glue, but go easy as it can distort the plastic. This improves the feel and reliability of the action a lot.
    « Last Edit: February 11, 2021, 06:30:58 PM by Tiposx »
    Logged

    TapTheForwardAssist

    • Member
    • *
    • Offline Offline
    • Posts: 45
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #14 on: February 13, 2021, 01:10:47 AM »

    When I ordered the G reeds from Charlie Marshall ... This improves the feel and reliability of the action a lot.

    Really good info! I took mine further apart and it seems that the pallet facing is some kind of soft white styrofoam, which seems to be working okay. Same thing on my air button, which has the same size of hole/pallet/facing as everything else.

    I'm taking pictures for my own records, but if anyone is curious to see the insides, I can post it.

    The reeds are sounding pretty good now, the action isn't terrible (I need to puzzle out if your way to improve the buttons is doable for me). At this point it's really the bellows that are the worst aspect (so crackly). So I'm going to talk to the guy at Flying Duck Concertinas who makes paper bellows, about how his simplified technique might apply to the Toys. I'm too busy to do this commercially, but it might turn out that a bored hobbyist could knock out a stack of paper bellows on Etsy and sell them as an upgrade, because it's really the worst part of these little things now that I've single-voiced mine.
    Logged

    Kimric Smythe

    • Hero Member
    • *****
    • Offline Offline
    • Posts: 712
      • Smythe's Accordion Center
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #15 on: February 13, 2021, 08:39:39 AM »

    I rebuilt a bunch of these for a class years ago.
    Some improvement of the reeds can be had by looking for ones with excess clearance and drifting the aluminum in to close up the gaps on the tip and sides. This makes a huge difference.
    It looks nasty but it works, I use a small flat tip screw driver and a anvil. https://www.instagram.com/p/CBl6ur1Js49/
    Logged
    Smythe's Accordion Center
    Pinole, California
    Sales and repairs since 1997

    Tiposx

    • Durham in England
    • Respected Sage
    • ****
    • Offline Offline
    • Posts: 259
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #16 on: February 13, 2021, 09:11:59 AM »

    That is an excellent tip, I will use it I am sure
    Thank you!
    Logged

    Winston Smith

    • Hero Member
    • *****
    • Offline Offline
    • Posts: 4066
    • AKA Edward Jennings
      • "Our Luxor B&B" Luxor life, slice by slice.
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #17 on: February 13, 2021, 09:20:42 AM »

    I remember a posting where someone told us about reducing the gap all around the reed tongue using nail varnish, or something related. Did anyone ever try that, according to what I read at the time, it seemed to do the trick admirably. Perhaps it could be a safer (and reversible) method?
    Logged
    At last, broken and resigned to accept conformity.
    Oh, how I LOVE Big Brother!

    Helena Handcart

    • Hero Member
    • *****
    • Offline Offline
    • Posts: 2452
    • Saltarelle Nell
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #18 on: February 13, 2021, 09:22:42 AM »

    Didn't Nick CB solve the bellows problem (to an extent) by connecting two sets of chanson bellows together and covering the whole lot in some sort of car paint?

    Found this video on YouTube
    Logged
    Saltarelle Le Romané  | Saltarelle Nuage | Oakwood | various elderly Hohners

    TapTheForwardAssist

    • Member
    • *
    • Offline Offline
    • Posts: 45
    Re: Converted my "toy accordion" melodeon to single voice; next steps?
    « Reply #19 on: February 13, 2021, 11:20:12 AM »

    I rebuilt a bunch of these for a class years ago.
    Some improvement of the reeds can be had by looking for ones with excess clearance and drifting the aluminum in to close up the gaps on the tip and sides. This makes a huge difference.
    It looks nasty but it works, I use a small flat tip screw driver and a anvil. https://www.instagram.com/p/CBl6ur1Js49/

    Instagram Caption: Closing up the side clearance on a Chinese concertina reed. I learned this trick from old instruments made during WWll that were made from rejected reeds. The clearance makes a huge difference in response and tone. I did this using a small hammer and the tip of a small screwdriver, it looks ugly but really works. This is a two tone reed so I could not just use a used Italian reed. #concertina #accordionreeds #accordion #accordionrepair

    Ah, so "drifting" means you kinda pounded the edges of the reed opening to get them closer to the reed itself?

    Is "anvil" in this context an actual small smith/cobbler anvil, or used more broadly to mean you just used something flat and heavy to be a solid surface for pounding around the reed? I assume this requires removing the individual reed from the reedblock, and can't be done while reeds are installed?

    Quote
    I remember a posting where someone told us about reducing the gap all around the reed tongue using nail varnish, or something related.

    I am also keenly interested in this option, as it might be a more accessible tactic for the average novice. I'm pretty open to ideas at this stage, just figuring out how to make melodeons accessible as best as one can.
    Logged
    Pages: [1] 2 3   Go Up
     


    Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
    SimplePortal 2.3.5 © 2008-2012, SimplePortal