Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3]   Go Down

Author Topic: Converted my "toy accordion" melodeon to single voice; next steps?  (Read 6428 times)

0 Members and 7 Guests are viewing this topic.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #40 on: February 19, 2021, 01:23:49 PM »

For tuners, are there any phone app tuners that are precise enough?

I also have ClearTune on my iPhone, which goes down to 0.1hz of accuracy, so would that suffice? I also have a Peterson Tuning Pickup (basically a clamp with a transducer and cord that plugs into my phone) so I can pick up the vibrations of the instrument without ambient noise.

Peterson iStrobosoft.
https://www.petersontuners.com/products/istrobosoft/

Also, think of your tuning work in cents, not Hz. Much more convenient.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #41 on: February 19, 2021, 01:50:39 PM »

The Peterson app is just about the best and very reasonable cost. Because it uses a simulated strobe display it is much easier to read, and much more precise at showing when you have reached your target pitch.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #42 on: February 19, 2021, 05:26:22 PM »

I also have ClearTune on my iPhone, which goes down to 0.1hz of accuracy, so would that suffice?

It would, because 0.1Hz corresponds to a tremolo beat rate of 1 beat in 10 seconds.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #43 on: February 19, 2021, 05:26:38 PM »

Well, yeah, but pretty much any phone app should suffice, ideally you would like one that has some kind of strobe tuning feature. You probably do not want to tune based on vibrational noise, the phones mic is probably a better choice.

That resolution is more than sufficient. Typically reeds are tuned very precisely to the appropriate pitch but that isn't really... Vital in this case.
Logged

TapTheForwardAssist

  • Member
  • *
  • Offline Offline
  • Posts: 45
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #44 on: February 20, 2021, 05:30:11 AM »

I had to google what a "strobe tuner" even is, and I'm still not entirely clear on what's great about them, but the Peterson iStroboSoft app is $10 so I guess I'll give it a whirl if they're that great.

I read the summary, I can sorta visualize it, but still don't entirely understand why it's better than a usual dial, but I guess I'll learn by doing: https://www.sweetwater.com/insync/what-is-a-strobe-tuner/

If I have fine tweezers for poking things, and needle files for scraping things, and combine those with an iStrobe, I should be equipped enough to work on a $35 melodeon?

UPDATE: I paid $10 on the App Store for the Peterson strobe tuner app, plugged in my $15 Peterson clamp-on transducer that plugs in my phone's earphone jack, and tuned up my $45 made-in-China 7-string pentatonic lyre. I emphasize this is just an initial impression, but said impression was "dang, this is way, way easier." I don't understand why it's easier, but I'ma gonna roll with it.

UPDATE2: used it on my Puerto Rican cuatro, which I have tuned open as a small cittern, and likewise very pleased with the ease. But it appears there are in-app purchases for "Sweeteners" like Just Temperament and similar, so we'll see how those add up since I do really need a tuner to do non-Equal options for my string instruments.

UPDATE3: $5.99 in-app purchase for the "Guitar Sweetener Pack" and $9.99 for the "World Instruments Sweetener Pack." So those have various DADGAD, perfect-fifths, etc. options, so I bought those under "in for a penny, in for a pound." There is also an Accordion Sweeter Pack that seems pretty informed on free-reed issues, but I'm holding off on that one for now since it's beyond what I need for toy fettling.
« Last Edit: February 20, 2021, 06:44:32 PM by TapTheForwardAssist »
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #45 on: February 20, 2021, 12:11:35 PM »

'Not clear on what's great about [strobe tuners]'
I have to sympathise because it’s not immediately obvious. The 'strobe' display, which is a simulation of the electromechanical strobe/spinning wheel thing on an old fashioned strobe tuner, shifts upwards for sharp and downwards for flat (of your target note) and sits still when your pitch matches, so it's easy to read (as Theo said). If you happen to be tuning (say) a guitar string, where you alter the pitch while the note sounds, this is really helpful. But tuning reeds (mostly) doesn’t work like this, cos you can’t alter the pitch while the reed oscilates. The Petersen iStroboSoft app also shows fractions of a cent, so it gives a degree of accuracy you can’t really get with a needle display (and it does a load of other things...check out the settings).  I do use this app (I’ve got two old iPads in my workshop..v handy), but I am a fan of the Kong Orchestral tuner (which costs quite a lot more than the Petersen). This has a real meter with a real needle, and little red lights that show when you are on target. It has a lot of other settings too, *and* you can get it to sound the pitch you want. BTW Not all tuners use the meter to tune. Some (well, at least one I know of) come from the piano tuning world and compare a reference sound with the reed, to get a match. So you can if you want do this with the Korg tuner. (Aside....old tuning benches before modern electronic tuners used this method...they had a set of reference reeds as part of the tuning bench).  Anyway, I often find it easier to grab the little Korg...it switches on quickly and is v handy. But I’m in minority of one on this, I suspect.

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #46 on: February 20, 2021, 04:21:41 PM »

My understanding is that you can also explain strobe tuners as: it lets you use a note's harmonics as a magnifying lens to more accurately detect the correct fundamental frequency.

Paying attention to the harmonics lets the device be more precise: if the device can only work to a precision of 1 Hz, then 1 Hz at the 2nd harmonic divides down to 0.5 Hz of precision at the fundamental. 1 Hz at the 4th harmonic is going to be 0.25 Hz of precision. It also helps you - as, in reverse, if you're 0.2 Hz 'off' at the fundamental, you would be 0.8 Hz off at the 4th harmonic, so, effectively, any error at the fundamental is magnified and easier to observe and gauge, and in turn, correct.

The 'strobe' element relates to how this approach could originally be implemented. If you've ever seen someone test a record player with a disc with black and white squares that 'drift' one way or the other when the record player is spinning too fast or too slow, but appear to stay in the same place when rotating at the correct speed, then, well, that's basically the same methodology - your home lighting is used as a 50 or 60hz strobe light that snapshots the position of the squares as they spin, playing a known frequency vs that of your record player. A the strobe tuner would spin a disc at the 'correct' speed, and flicker a light based on the sound it heard. Nowadays, quite a few mobile apps offer some kind of virtual display that reflects this same kind of information, although they may not display it in exactly the same way as a strobe disc.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #47 on: February 20, 2021, 07:08:16 PM »

Probably very useful for tuning a bell, which has all sorts of harmonics going on.

TapTheForwardAssist

  • Member
  • *
  • Offline Offline
  • Posts: 45
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #48 on: February 21, 2021, 05:57:32 PM »

@Steve_freereeder, the Peterson iStroboSoft is already earning its keep, both on my lyre and cuatro, as well as on the toy melodeon.

Played through the mic, it quickly showed me the M bank is running mostly on average +15c, with a few notes being +8c and a couple being +23c. As noted the C/D button I need to play musical chairs with since the decent reeds are on differing banks, and the High g is still clogged and I need to puzzle that one out.

So with that in mind, should I first experiment in lowering the pitch of the M+ reeds so if I muck it up I ruined the worse of the two? And I'm glad to hear it's filework, because I know nothing about reed fettling had assumed that one lowered pitch by adding mass via a smear of solder or something, so this should be easier.
Logged

TapTheForwardAssist

  • Member
  • *
  • Offline Offline
  • Posts: 45
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #49 on: March 02, 2021, 08:01:13 PM »

Been tied up with work, but definitely going to get back to fine-tuning my M bank down to C.

Quick question: would it be removed feasible to tune my M+ bank up to D, so I could have both a C box and a D box (on the right hand at least) depending which bank I taped off? Or is tuning a reed up nearly a full-step just not viable?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #50 on: March 02, 2021, 08:06:10 PM »

Probably ok on the lowest reeds but progressively more tricky as you go higher and on the highest reeds not possible.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

TapTheForwardAssist

  • Member
  • *
  • Offline Offline
  • Posts: 45
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #51 on: March 03, 2021, 07:45:06 PM »

One more question before I get back to hacking on this critter: when folks tune reeds, do they usually do it with their bare eyes (with goggles), or is it common to use magnification so you can see more clearly what you're scraping?

I keep a jeweler's loupe (5x magnification) in my kit for various tasks, so should I try wearing that, or just protective goggles when tuning reeds?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #52 on: March 03, 2021, 08:13:03 PM »

I use unaided eyes for tuning.  I do keep a 10x magnifier handy to examine the edge of reeds that are not sounding correctly.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #53 on: March 03, 2021, 11:57:17 PM »

One more question before I get back to hacking on this critter: when folks tune reeds, do they usually do it with their bare eyes (with goggles), or is it common to use magnification so you can see more clearly what you're scraping?

I keep a jeweler's loupe (5x magnification) in my kit for various tasks, so should I try wearing that, or just protective goggles when tuning reeds?

Goggles?? What are you using to tune your reeds? A grinding wheel?

Filing or scraping reeds should be done using hand tools only, and these used very gently. No dremels or other mechanical devices, despite what you may find on Youtube. Wear magnifying glasses by all means if it helps your vision, but goggles are not necessary - there should be no flying debris. (If there is, you're doing it wrong.)

I've posted this video earlier in the thread. This is how it should be done:
https://www.youtube.com/watch?v=rdap-lYsKbw

How not to do it:
https://www.youtube.com/watch?v=lHi9W0YxFTI
Tuning with the reed blocks outside the instrument (pitch will change when replaced in the instrument)
Using a dremel (too harsh, risks damaging reed tongue and reed plate slot, either through abrasion or overheating)
Using inappropriate valve material (old magnetic tape)
I wouldn't let this person get within a mile of my instruments.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

TapTheForwardAssist

  • Member
  • *
  • Offline Offline
  • Posts: 45
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #54 on: March 05, 2021, 05:56:52 PM »

I'll be using hand tools (got a full set of needle files), but I've got some worksite safety background so whenever I deal with small pieces of wood or metal  I like to wear goggles.

Thanks for posting the do/don't examples on tuning, very helpful!
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #55 on: March 11, 2021, 07:15:14 AM »

"https://www.youtube.com/watch?v=lHi9W0YxFTI
Tuning with the reed blocks outside the instrument (pitch will change when replaced in the instrument)
Using a dremel (too harsh, risks damaging reed tongue and reed plate slot, either through abrasion or overheating)
Using inappropriate valve material (old magnetic tape)
I wouldn't let this person get within a mile of my instruments".

Pretty rude to slag on somebody you have never met.

You are off on several accounts here by the way. You can't really heat the reed up enough in this manner to have any effect on the temper under normal circumstances, many Honers show signs of this sort of tuning from the factory going back decades.
A properly set up tuning table will give very little deflection to the tuning. I seldom have to tune more than 1-2 reeds post table on a 3 reed 120 bass piano accordion.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #56 on: March 11, 2021, 07:45:48 AM »

"https://www.youtube.com/watch?v=lHi9W0YxFTI
Tuning with the reed blocks outside the instrument (pitch will change when replaced in the instrument)
Using a dremel (too harsh, risks damaging reed tongue and reed plate slot, either through abrasion or overheating)
Using inappropriate valve material (old magnetic tape)
I wouldn't let this person get within a mile of my instruments".

Pretty rude to slag on somebody you have never met.

You are off on several accounts here by the way. You can't really heat the reed up enough in this manner to have any effect on the temper under normal circumstances, many Honers show signs of this sort of tuning from the factory going back decades.
A properly set up tuning table will give very little deflection to the tuning. I seldom have to tune more than 1-2 reeds post table on a 3 reed 120 bass piano accordion.

Sorry, I totally disagree.

Using a dremel to tune reeds risks damage to the reed tongue or the reed plate slot. It's as simple as that. Why use a noisy machine which is slow to run up to speed and potentially difficult to control in a small confined space? Hand tools are ready for immediate use, are silent, and completely controllable.

Any tuning table, no matter how it is set up, will always show a variation when comparing the pitch of the reeds on the block outside the instrument to the pitch in situ in the instrument. It's to do with the proximity of other components inside the instrument, which usually cause flattening in pitch compared with the pitch outside the instrument. Which is why professional tuners at the factories tune the instruments with the reeds mounted inside the instrument. That's good enough for me.

Finally, using old magnetic tape, instead of proper valves with multiple spring leaves, is simply bad practice. Proper valves are available. If we are working on other people's instruments and charging money for our services, we have a responsibility to use proper components and working practices.


Edited to add this:

Quote
many Honers show signs of this sort of tuning [i.e. with a dremel] from the factory going back decades.

Maybe, but you don't see dremel marks on Castagnari instruments. Sometimes the occasional diagonal filed area in the middle of the reed, but usually any fine flattening adjustments are made using longitudinal scratch marks with a reed scraper, which leave the edges of the reed tongue intact, and therefore less likely to initiate a crack across the reed.

Using a dremel for tuning will usually result in a concave zone across the width of the reed tongue, and the reed will be thinned and weakened in that area, again leading to a zone for potential subsequent fracturing. Furthermore, the concave zone makes it less likely that the reed will withstand future tuning adjustments, due to relatively large amounts of metal having been removed from a small area.

Hand tools such as files and scrapers allow you to 'feel the steel' as you are working, and you get to know by experience how much to to scrape or file to achieve the required adjustment. I learned very early on to always treat reeds with respect. The bit in the Hippocratic Oath primum non nocere (first do no harm) definitely applies to working with reeds.
« Last Edit: March 11, 2021, 10:31:49 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Converted my "toy accordion" melodeon to single voice; next steps?
« Reply #57 on: March 11, 2021, 08:31:13 AM »

This is getting wonderful, we now have two threads that are individually guaranteed to run for ever under one topic. For those new age philistines who admit to using social media, this is the time to insert the popcorn GIF.  >:E >:E >:E >:E 
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."
Pages: 1 2 [3]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal