Forgive me for not knowing much of the technical stuff here but one of my notes (high D on the G row) only has one bit to it...
I'm guessing this is something to do with it being a two voice box and only one of the reeds working (if that is right, then it's only stuff I've picked up from reading the threads on here.... )
What do I do?
It does sometimes happen that a bit of dust, fluff - even a hair, lodges in the tiny gap between the steel reed tongue and the aluminium reed plate which the tongue is mounted on. It will be enough to stop the reed tongue vibrating properly.
As some have said, it can sometimes be freed by a bit of hard pushing or pulling on the offending reed, but often this fails to cure the problem and you have to open up the box.
Opening up your melodeon is not difficult, but you just need to take a bit of care.
Work in a good light on a table top covered with a soft towel or similar to avoid damage to the melodeon or the table.
1. Remove the bellows pins which secure the treble end to the bellows. There are usually 4, sometimes 6 of them, and will look like rounded nail heads protruding a little way from the surface of the wooden ends. You will need a pair of pliers to pull them out. They might be a bit stiff, but they
will come out with a straight, vertical pull. It is a good idea to cover the rounded pin head with a scrap of fabric before closing the pliers on it; it helps avoids damaging the pin head and the side of the melodeon. Lay the pins down safe so they can't roll off anywhere and get lost. I like to make sure I know which pin comes from which hole, so I can return the correct pin to the correct hole on reassembly.
2. Once all the bellows pins are removed, the RH end should be able to be freed from the bellows. Again, it might be a bit stiff, but just gently ease it off. Lay the bellows and LH end safely to one side (inside the case is usually a good idea).
3. Inside the RH end, you should now be able to see the reed blocks and all the reeds. Take care not to bend any of the thin plastic or leather valves. The reed blocks are the two upstanding wooden structures on which the reeds are mounted. One reed block will be for the G row, the other for the D row. The reed tongues are the steel springy things set in the aluminium plates. Each note on your melodeon has two reeds on opposite sides of each reed block (that's why it is called a 2-voice instrument). And each reed plate contains two reeds, the visible one for the push notes and a hidden one underneath for the pull notes, the slot of which is covered by the leather or plastic valve.
4. You need to identify (a) which reed block is for the G-row - it will be the block which contains the overall shorter reeds, and (b) which reed plate is the one which is causing the problem. Count along the keyboard for the relevant button, and then count along the reed block to find the equivalent reed. You are fortunate in this case as your problem note is a push note and the reed tongue will be one of the visible ones rather than the one hidden underneath. Once you have found the correct position, there will be two reed plates for that particular note, on opposite sides of the reed block.
5. Having identified which number reed plate is the problem one, you
may be able to see if there is any fluff or dirt in the gap, but on the other hand it may be too small and hidden to see. Gently flick or 'twang' the steel tongue using a fingernail or preferably a small wooden pointy thing like a cocktail stick. Do this to both reed tongues on opposite sides of the reed block. Usually this is sufficient to clear any dirt or debris.
6. In doing all this, take care not to bend any of the leather/plastic valves - they are rather delicate and easy to crease. And try to avoid touching the reed tongues with your fingers if possible - some people's sweat can be rather corrosive over time and may encourage rusting of the reed tongue. Resist the temptation to blow on to the reeds; moist breath can also be detrimental to the steel reeds.
7. Reassemble the melodeon and try it out to see if you've cured the problem. When reassembling the RH end to the bellows, make sure you have it on the correct way round and that the bellows are pushed firmly into the RH end, before you attempt to push the bellows pins back into place. Make sure the bellows pins are correctly aligned and perpendicular before trying to push them into place. They may be a bit stiff, but if everything is lined up properly, a firm push should do the trick. You can use a coin or thimble to protect your thumb when pushing the pins back in. Make sure the pins are fully pushed home.
If this hasn't cured the problem, repeat all the steps and try again. If it persistently fails to work it may be that something else is wrong in which case ask for more help.
All this may seem very daunting when written down but once you actually start doing it, the stages and descriptions should logically fall into place. Just go carefully and slowly and you'll be OK and also will learn a lot about how your melodeon works.