Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Help with understanding all about reeds (a Primer?)  (Read 1148 times)

0 Members and 1 Guest are viewing this topic.

Von Colborn

  • Member
  • *
  • Offline Offline
  • Posts: 5
Help with understanding all about reeds (a Primer?)
« on: October 13, 2021, 08:07:19 PM »

Hey,  it's me again -  the newbie with all of the questions. I've done a lot of online reading and video watching (Hot Rodding series among others) this past couple of weeks.  I have an increased vocabulary and some understanding,  too.  Other than partially deconstructing and reassembling my squeeze box it has been to this point more academic than not. I've ordered a few odds and ends,  including deed wax and some new leather valves.

One area that I need a lot more understanding in with the reeds.  My Melodeon has some reeds that sound great,  others that don't sound at all,  and others that are really weak when compared to their counterpart.  Those that sound great also have a reasonable tremolo. Several of the leather valves are turned up and a few are missing completely.

I don't have any kind of a tuning table (where bellows are used as a test bed for the wooden reed blocks). In lieu of that I have been using the source that God gave me,  my lungs and lips. It is not the best solution but have have been able to replicate the problems that I identified when the instrument was assembled.

Questions:
  • Other than damage,  what causes a Reed to either stop sounding or sound poorly?
  • Some of the Reed plates have a capital H stamped on them.  Otherwise there are no identifying marks such as which notes are on that plate.  What does the H mean?  How does one know which notes are on a plate and how do you keep them identified if you are rewaxing the entire Reed block?
  • What is the preferred adhesive is preferred for affixing the leather valves to the Reed plate,  a water-based glue?
My first pass at refurbishing my instrument is to get it to the point where I can start learning how to play it. If I like playing it I will take it to the next level,  either through my own attempts or paying someone to do it for me.

Thanks in advance for all of the great advice that I know I will receive.  I've already read so much great info on this forum and I'm sure there is much more to come.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Help with understanding all about reeds (a Primer?)
« Reply #1 on: October 13, 2021, 08:49:36 PM »

  • Other than damage,  what causes a Reed to either stop sounding or sound poorly?
  • Some of the Reed plates have a capital H stamped on them.  Otherwise there are no identifying marks such as which notes are on that plate.  What does the H mean?  How does one know which notes are on a plate and how do you keep them identified if you are rewaxing the entire Reed block?
  • What is the preferred adhesive is preferred for affixing the leather valves to the Reed plate,  a water-based glue?


1. Could be a bunch of things


 Not sounding at all
  • Dirt/dust caught between the reed tongue and the plate - just ping the reed should clear it
  • Reed set too low preventing it starting - bend the  reed up a bit, usual starting point is for the reed tip to be above the plate by ~ the thickness of the reed tip.
Slow to start
  • Reed set too high needing to much air to start it - bend reed as above.
Sounding poorly
  • Is the reed central in the slot, check by holding up to a bright light - if offset I insert a scalpel blade in the tight side and ease the reed over in the slot as required.
2. H are probably Hohner reeds. When removing reed plates prior to rewaxing I usually try to keep them in order so it is easy to refit them in the right order. I use sandwich trays from Amazon. If they get mixed up you just need to sound the reeds then work it out from the keyboard layouts on melnet and observing which pallets the keys raise where they go, as they say it's not rocket surgery.


3. I use EvoStick Impact adhesive, I only apply it, sparingly to the valve then place it on the plate immediately. Others use different adhesives.


Good Luck!

Von Colborn

  • Member
  • *
  • Offline Offline
  • Posts: 5
Re: Help with understanding all about reeds (a Primer?)
« Reply #2 on: October 13, 2021, 09:24:34 PM »

  • Other than damage,  what causes a Reed to either stop sounding or sound poorly?
  • Some of the Reed plates have a capital H stamped on them.  Otherwise there are no identifying marks such as which notes are on that plate.  What does the H mean?  How does one know which notes are on a plate and how do you keep them identified if you are rewaxing the entire Reed block?
  • What is the preferred adhesive is preferred for affixing the leather valves to the Reed plate,  a water-based glue?


1. Could be a bunch of things


 Not sounding at all
  • Dirt/dust caught between the reed tongue and the plate - just ping the reed should clear it
  • Reed set too low preventing it starting - bend the  reed up a bit, usual starting point is for the reed tip to be above the plate by ~ the thickness of the reed tip.
Slow to start
  • Reed set too high needing to much air to start it - bend reed as above.
Sounding poorly
  • Is the reed central in the slot, check by holding up to a bright light - if offset I insert a scalpel blade in the tight side and ease the reed over in the slot as required.
2. H are probably Hohner reeds. When removing reed plates prior to rewaxing I usually try to keep them in order so it is easy to refit them in the right order. I use sandwich trays from Amazon. If they get mixed up you just need to sound the reeds then work it out from the keyboard layouts on melnet and observing which pallets the keys raise where they go, as they say it's not rocket surgery.


3. I use EvoStick Impact adhesive, I only apply it, sparingly to the valve then place it on the plate immediately. Others use different adhesives.


Good Luck!

Hey Lester,  thanks for the insite.  You hit squarely on one of the questions that I forgot to ask. "What is the correct placement of a Reed relative to the Reed plate/hole?" I was wondering if the tip of the Reed should be above the plate or if it should protrude into the hole a little. I have noticed that some of the tips are below the plate but I have not noticed a correlation between those that are not sounding and necessarily having their tips lower than you described.  I'll play with that some more. 

I determined the low tip situation while I was using a razor knife to catch the tip so that I could ping the reeds.  It did not seem to make a difference in the sound (trying to clean any foreign debris from between the Reed and the plate).  What I did notice was a difference in the sound produced when I flipped reeds.  Those that were voicing correctly had a definite "ting" sound and the other was more of a "tunk" sound as if it was hitting an obstruction.  I know that the Reed should be placed over the hole in the plate with a very small opening on the three sides.  I have noticed that some of the reeds are not properly centered as described.  Is it possible that they reposition over time on their own? Is it possible that a Reed could come out of the factory and be too long for the opening?

I have a long history of always having more questions in response to answers to previous questions.  Sorry.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Help with understanding all about reeds (a Primer?)
« Reply #3 on: October 13, 2021, 09:31:08 PM »

If the reeds are not uniformly bright and clean your will need to clean then carefully to remove rust and dirt.  Anything on the edge of the reed tongue may make contact with the reed plate when the reed moves and will prevent it sounding.   A thorough cleaning is the first step.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Help with understanding all about reeds (a Primer?)
« Reply #4 on: October 13, 2021, 09:32:42 PM »

The rivets can become a bit loose over time and the act of scraping the rust etc can slightly move the reed tongue requiring the resetting. If the reed does this often during the tuning  I tend to make sure I've set it correctly then give the reed a tap with my hammer on my anvil substitute a short length of narrow gauge railway track to tighten its grip :)

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Help with understanding all about reeds (a Primer?)
« Reply #5 on: October 14, 2021, 06:21:39 PM »

If the plates are zinc they can develop bumps that will jam the reeds. You have to scrape/file these away to get them to sound. Gapping can affect volume too , a slightly larger gap can give more volume but too much affects response. Very stiff but still flat valves will really cut volume too.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Help with understanding all about reeds (a Primer?)
« Reply #6 on: October 16, 2021, 07:09:54 AM »

You will also have trouble getting some reeds to sound by blowing on them if your mouth opening is a harmonic fraction that will cause the reed to "lock". Sheng instruments use this principal to allow you to play a 20 reed instrument with 8 fingers. You block the node hole to get the note to play.
 This will also make it nearly impossible to tune a reed due to the distortion.
 You can defeat this to some degree by pulling your mouth away from the block and blowing from a distance. This will cause the locked reeds to play.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal