Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: HA114 woes  (Read 3338 times)

0 Members and 1 Guest are viewing this topic.

Jesse Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 761
  • Buffalo, NY, USA
HA114 woes
« on: December 17, 2021, 01:42:48 AM »

My HA114D is just beset with problems lately. Advice welcomed on whether to let a pro handle some of this or if this is something I could manage myself.

Two of the M+ reed plates (for buttons 4 and 5) are not solidly planted in the wax. Twice now, I have picked up the box and noticed something sounds off. Isolating the various stops led me to identify these two buttons making a horrible windy noise (with occasionally strangled attempts at the note). Opening the box I discovered that the two plates were tipped forward off the block, lifted up at the bottom (in the "V" of the two reed blocks). Using the eraser end of a pencil, I carefully but firmly pressed the plates back down, and that seemed to "solve" the problem for quite awhile. Until I picked up this box today after a long period of neglect and discovered the problem had returned.

Is it difficult to "spot fix" the wax on these two plates? I know the 114s are notoriously difficult to wax, especially in the middle two banks of reeds. I suppose that's why the wax is failing here; the last time it was waxed they must not have built up a sufficient seal between the block and the plate. I can't even see the wax line since it's down in the "V". How hard would it be to touch up the wax with a wax stick and a soldering iron?

Second problem: the bass spoon spring broke just now! For an immediate fix I will probably steal a spoon off my HA114C. Longer term, how difficult is it to replace the spring itself? I don't see replacement springs at Charlie Marshall, and also it looks like there is a rivet that will need to be filed out in order to get the spoon apart, correct? Will I be happier just ordering a whole new spoon from CGM?

Thanks!
Logged
Hohner Pokerwork D/G (x2!), Hohner one row four stops in D and C, Hohner Presswood C/F.

Jesse Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 761
  • Buffalo, NY, USA
Re: HA114 woes
« Reply #1 on: December 17, 2021, 01:47:24 AM »

Aha, on closer examination I see that where there is normally a rivet there is a little screw, meaning someone has dealt with this problem before, and the spring wire is much thicker than in the other two spoons! Used instruments... always an adventure. Just like home improvement projects in an old house.
Logged
Hohner Pokerwork D/G (x2!), Hohner one row four stops in D and C, Hohner Presswood C/F.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: HA114 woes
« Reply #2 on: December 17, 2021, 05:02:50 AM »

If you have reeds falling out of the wax, it’s almost certain that the rest of the wax is no good anymore and all of it will need to be replaced.
« Last Edit: December 17, 2021, 05:04:54 AM by mselic »
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: HA114 woes
« Reply #3 on: December 17, 2021, 08:01:22 AM »

Quick and dirty fix for the loose reed plates…if you have a soldering iron you can melt the wax near the loose plates to get it to adhere again. It’s not pretty but it generally does the trick, esp if you don’t want the expense etc of having the whole reed shebang stripped and rebuilt.  On the spring problem. You can make a spring using some old guitar string wire (you'll have to find one of suitable gauge). I use piano wire but I’m guessing there is more likelihood you have access to old wire strings (obvs not the wound ones). Or look on eBay. You can buy a small amount of piano wire on there. Or I have seen a paper clip used for this purpose (though it’s not very springy and not a great idea). To get the 'winds', get a block of wood and hold down one end of the wire with a screw. Site another screw nearby (or a nail) and grab the wire with pliers and wind around the screw. You'll need a couple of pairs of pliers (long nosed ones are good) and some small cutters. After some experimentation you'll be making springs like a pro. Of course someone else will be along directly with other advice (probably to say I’m wrong (:) )
« Last Edit: December 17, 2021, 08:07:50 AM by RogerT »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: HA114 woes
« Reply #4 on: December 17, 2021, 08:33:10 AM »

I agree with most of what has been said.  If some reeds are loose you need a full re-wax,  but you can do a temporary fix with a soldering iron.  Re-waxing a 114  is not that difficult once you have done a few!  If yours is being played regularly it will need to be done soon or later.

Springs — piano wire (aka spring wire or music wire)is what you need, 0.7mm diameter I think.  I very much doubt if any guitar uses such heavy steel strings.  Paper clips are useless, the steel is too soft.  A safety pin can be cut down to make a spring, but is not as good as piano wire.  Fitting the spring require care to avoid injuries to the fingers.  The spring has to be held closed while you get it in position and fit the rivet.  If it slips from your holding device it can fly open and break your skin.  I hold the spring closed by slipping the legs into a length of small diameter brass tube,  just leaving the coil protruding.
The easy fix is to buy a new spoon from Hohner.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: HA114 woes
« Reply #5 on: December 17, 2021, 08:42:50 AM »

What Theo said. And wear some eye protection when clipping the wire.

Chris Rayner

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 467
Re: HA114 woes
« Reply #6 on: December 17, 2021, 11:21:34 AM »

If you’re using proper piano wire, as is best for springs, ordinary wire cutters will go blunt quite quickly.  I use one of these: https://www.heamar.co.uk/cutters/43910-xuron-2193-music-wire-shear-cutter-615265901919.html?gmc=3&gclid=CjwKCAiAh_GNBhAHEiwAjOh3ZOFK-DGoEZO5ydQiPrSzVIdsLUo3aizgyb8d7NKITZm97sG4dLWC1RoCmCUQAvD_BwE
Logged
Elderly amateur musician hoping to stave off dementia by learning to play the melodeon.  Main instrument a Tommy, also D/G and G/C pokerworks,  a single row 2 stop Hohner, and a new addition to the free reedery, a rather splendid Paolo Soprani four voice 120 bass c-system chromatic button accordion.  Very shiny, very loud, and about the same size and weight as a small car.  Now I’ve traded me Benny with (ahem) a cash adjustment, to a three voice 60 bass Castagnari K3.

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: HA114 woes
« Reply #7 on: December 17, 2021, 01:21:30 PM »

What a spiffing idea those shears are!  I don't like touching spring wire with pliers, etc whilst forming the spring.  Basically, a number of brand new springs will fail as whatever gripped the wire to bend it will have damaged the surface, this becoming a stress riser once the wire is flexed in service.  I favour the idea of slipping a close fitting plastic pipe over the wire as a grip/lever.  If nothing suitable is available from the scrap box (a.k.a. house) then at least wrap tape around the pliers' jaws to prevent metal to metal contact and subsequent damage.

Rob.

P.S. I reckon you'd do well to buy a new spoon, which you can fit immediately, then find suitable wire for new spring... So satisfying to reflect on how you've been able to play during the months it took to source wire, make spring and recover from injuries.

Wax loses stickiness with age and re-melting it has very limited effect.  It really needs removal and replacement with fresh wax so as to not dilute the benefits of the new wax.
« Last Edit: December 17, 2021, 01:28:55 PM by Rob2Hook »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: HA114 woes
« Reply #8 on: December 17, 2021, 01:35:28 PM »

A pair of round nose pliers are good for occasional spring coiling. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: HA114 woes
« Reply #9 on: December 17, 2021, 01:59:54 PM »

Spoons. Not uncommon for folks to do a "temporary" fix with a safety pin with ends clipped off. Problem is that after a while it breaks again. Usually when you least need it to! If yours has a "thick spring" i suspect its had this fix sometime. I use piano wire (thickness depending on how stiff you like your springs). i find it easier to fit springs by taking the spoon off the growl box first. I use a 2mm split pin instead of a rivet. Might as well check the other two spoons at the same time. Be careful, the two tiny securing screws can easily get lost and/or can spring out and strip the thread in the wood. If its an old 114 you might as well renew the leather seals on the spoons unless its been done already. All that is pretty easy stuff even if you've never done it before. I can post springs /split pins if you need them.

114 wax...Id say definitely not a job to tackle if its your first go at waxing. Ive waxed many models and find the 114 the most difficult of all. I use the soldering iron method.  The two outer reed blocks are straightforward but the two mids blocks harder. It can be tricky to get wax along the bottom edge of the reed plate and all too easy to inadvertantly melt a valve. Ive tried a few different ways of doing it. Ive settled on fixing the first reed plate followed by the first reed plate on the opposite reedblock bringing the soldering in at 45 degrees from the opposite end of reedblock so no valves are close to the soldering iron. Then work back fixing reeds on opposite reedblocks until all 20 are done. Anyone got an easier way?

while all the reeds are out they can be cleaned and re-valved before re-waxing. When done the whole box will need retuning. I make sure the two tricky mid registers are tuned slightly sharp before waxing them in. Its easier to flatten them than sharpen as the blocks are so close together and it difficult to access the pull reeds..
Logged

Jesse Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 761
  • Buffalo, NY, USA
Re: HA114 woes
« Reply #10 on: December 17, 2021, 02:19:42 PM »

Ugh, at that point it would probably be less expensive to just buy a new box, when you factor in overseas shipping to a reputable fettler for a full rewaxing and retuning job.

It's not easy owning melodeons in the US. Why couldn't I have just taken up the fiddle?
Logged
Hohner Pokerwork D/G (x2!), Hohner one row four stops in D and C, Hohner Presswood C/F.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: HA114 woes
« Reply #11 on: December 17, 2021, 02:57:27 PM »

Ugh, at that point it would probably be less expensive to just buy a new box, when you factor in overseas shipping to a reputable fettler for a full rewaxing and retuning job.

It's not easy owning melodeons in the US. Why couldn't I have just taken up the fiddle?

It's not easy to find a Hohner 114 in D.  I don't think Hohner make them any more, and examples in D have always seemed scarce compared with C or G.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jesse Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 761
  • Buffalo, NY, USA
Re: HA114 woes
« Reply #12 on: December 17, 2021, 03:26:35 PM »

It's not easy to find a Hohner 114 in D.  I don't think Hohner make them any more, and examples in D have always seemed scarce compared with C or G.

Yes, that's exactly why I jumped on it when I saw it on eBay from a seller who knew what he was talking about (unlike most eBay melodeon sellers). According to the seller, the box was "recently" retuned by an accordion shop in the US whose name I recognized. I would assume that it was rewaxed at that point, which is why I'm a bit skeptical that the entire box would need to be rewaxed now. Or perhaps the tuning was just "touched up" in place without removing the reed plates?

IIRC I think Hohner has discontinued the entire 114 series (as well as 113 and 112).
Logged
Hohner Pokerwork D/G (x2!), Hohner one row four stops in D and C, Hohner Presswood C/F.

Jesse Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 761
  • Buffalo, NY, USA
Re: HA114 woes
« Reply #13 on: December 17, 2021, 04:07:45 PM »

OK, I successfully swapped the spoon from my 114C to the 114D and that is working fine. So the malfunctioning spoon turns out to have a "homemade rivet" where some former owner put a small screw through the pivot holes and then squeezed the point of it to prevent it from coming back out.

Hohner USA does not list replacement spoons on their website (maybe I'll give them a call and see) and the Hohner.de says, with classic German bluntness, "Kein Versand nach USA und KANADA." So maybe I'll order a replacement spoon from Charlie Marshall, along with some wax sticks to attempt a spot fix to hopefully limp along for a while longer. I think we oddball melodeon owners in the US are rather forced to patch things together with duct tape and chewing gum.
Logged
Hohner Pokerwork D/G (x2!), Hohner one row four stops in D and C, Hohner Presswood C/F.

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: HA114 woes
« Reply #14 on: December 17, 2021, 04:38:14 PM »

Could you maybe find a model engineer who could turn you up a new rivet?
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Jesse Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 761
  • Buffalo, NY, USA
Re: HA114 woes
« Reply #15 on: December 17, 2021, 05:18:26 PM »

Could you maybe find a model engineer who could turn you up a new rivet?

I saw someone here recommend using a split pin, which makes future removal much easier.
Logged
Hohner Pokerwork D/G (x2!), Hohner one row four stops in D and C, Hohner Presswood C/F.

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: HA114 woes
« Reply #16 on: December 17, 2021, 05:20:07 PM »

It's not easy to find a Hohner 114 in D.  I don't think Hohner make them any more, and examples in D have always seemed scarce compared with C or G.

Yes, that's exactly why I jumped on it when I saw it on eBay from a seller who knew what he was talking about (unlike most eBay melodeon sellers). According to the seller, the box was "recently" retuned by an accordion shop in the US whose name I recognized. I would assume that it was rewaxed at that point, which is why I'm a bit skeptical that the entire box would need to be rewaxed now. Or perhaps the tuning was just "touched up" in place without removing the reed plates?

IIRC I think Hohner has discontinued the entire 114 series (as well as 113 and 112).
Probably not retuned after complete new valves and re waxing job, could be spot tuned reusing the wax and someone might claim it was recently tuned.

So yeah I bet it was just touched up.

There are repairers near you no?
Hickorywind a member here repairs and tunes them.

Did you try the button box? Pretty sure they still would repair.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: HA114 woes
« Reply #17 on: December 17, 2021, 06:19:47 PM »

Lots of fettlers in the US - The Button Box is the first that comes to mind and they can certainly overhaul that instrument for you. No need for shipping outside the country.
Logged
C#/D player

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: HA114 woes
« Reply #18 on: December 18, 2021, 01:53:02 AM »

Scott Bellinger (Hickorywind) is not far from you, in Rochester, NY. See link here: http://forum.melodeon.net/index.php/page,shops_repairers.html
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: HA114 woes
« Reply #19 on: December 18, 2021, 02:38:28 AM »

ok if its all been rewaxed and plates are pushing loose from the rivet end i suspect when you go for the push notes the plates are not holding because there isnt enough wax top hold the reeds. this could be fixed by getting more wax between the two mid reed blocks. tricky thing is getting the wax in there without damaging the valves from the heat of the soldering iron. you could try heatproof foil (used on car exhausts) over both reed banks.....leave a gap near the rivet so the wax doesn't stick to the foil. get the soldering iron just hot enough to melt the wax (around 80c or slightly above) and run a bead of wax along the gap between both reed banks. as long as the heat from the soldering iron doesn't affect the valves you might fix it.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal