Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Rewaxing 4-stop Hohner.  (Read 2543 times)

0 Members and 1 Guest are viewing this topic.

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Rewaxing 4-stop Hohner.
« on: May 07, 2022, 02:25:16 PM »

My HA114 has been worked hard over the last couple of months.
I knew the wax wasn't in the best of order and a couple of plates were rattling around when I got it.
Now a buzz has started on one button and another is slightly out of tune, so it's clear I need to strip it and renew the wax and valves.
This is the version with 2 parallel blocks glued in place and there's not much room. I had no problems working on the other 4 stop with flat mounted reeds.
Any tips on waxing? I normally use either a brush (very slow) or a flat spoon which I'm not sure I've got room for. I could make a special one....
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Rewaxing 4-stop Hohner.
« Reply #1 on: May 07, 2022, 02:40:13 PM »

Here be dragons!
My hands aren't steady enough to make an even half decent job of them. Good luck!!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Rewaxing 4-stop Hohner.
« Reply #2 on: May 07, 2022, 03:03:14 PM »

Gravity is your friend here.  It is possible to run molten wax along the gap between two reed plates.  Position the box so that there is a slight slope to get the wax running in the right direction.   When placing the reds put a coat of melted wax on the end that is furthest from the top of the reed block.  This seals the end of the reed and helps to hold the reed plate in place while you wax the edges. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Rewaxing 4-stop Hohner.
« Reply #3 on: May 07, 2022, 03:52:45 PM »

In a similar way to Theo's method I attach a small bead of wax to the bottom of the reed then slide it in place, then wax the top of the reed and use gravity for the sides.

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Rewaxing 4-stop Hohner.
« Reply #4 on: May 07, 2022, 04:26:51 PM »

Right.
I'm going in.










Just not yet
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Rewaxing 4-stop Hohner.
« Reply #5 on: May 07, 2022, 06:27:35 PM »

"Just not yet"

Chicken!!!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Rewaxing 4-stop Hohner.
« Reply #6 on: May 07, 2022, 07:54:00 PM »

"Just not yet"

Chicken!!!
Possibly. But.....
I have a couple of more pressing jobs already laid out.

I thought, just for a change, that I'd ask advice before I started. I might remelt around the buzzy reed just to keep it going, but it does need serious attention.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

windybutton

  • Member
  • *
  • Offline Offline
  • Posts: 32
Re: Rewaxing 4-stop Hohner.
« Reply #7 on: May 24, 2022, 02:55:54 AM »

I’ve watched a fella dip the rivet end just a little into wax then pop into
position on reed block before pouring wax between plates .
I’ve yet to give in a go.
Logged

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Rewaxing 4-stop Hohner.
« Reply #8 on: May 24, 2022, 05:11:01 AM »

Try not to drop the whole reed into the wax pot.  I, uh, know someone who did that once.
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Rewaxing 4-stop Hohner.
« Reply #9 on: May 24, 2022, 12:23:22 PM »

Do they float ??  ;)
Logged

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Rewaxing 4-stop Hohner.
« Reply #10 on: May 24, 2022, 04:18:34 PM »

I'll ask.
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Rewaxing 4-stop Hohner.
« Reply #11 on: May 25, 2022, 05:58:55 PM »

 ;D
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Rewaxing 4-stop Hohner.
« Reply #12 on: May 25, 2022, 06:44:35 PM »

Somebody here reading this has a wicked sense of humour.
I got a large packet in the post and I now have two to do.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Rewaxing 4-stop Hohner.
« Reply #13 on: May 31, 2022, 07:38:42 AM »

Well it's not pretty but seems to work.
I now have another problem, playing the higher notes I am getting bleed of air from the note I'm playing to nearby ones. Is this a job for getting the reed block of and re gluing?
Is there a better way or am I missing something?
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Rewaxing 4-stop Hohner.
« Reply #14 on: May 31, 2022, 08:21:15 AM »

It could be air leaking through a loose or misaligned register slide.  First thing to check is that the register slides are travelling the correct amount so that they open and close fully.  Or if it’s the same note that’s sounding it could be a split if knot hole in the midrib of the block. The chamber walls are fairly thick in a 114 so damage to the wood is unlikely.  Another possibility is a cracked glue line at the top or at the base of the block.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Rewaxing 4-stop Hohner.
« Reply #15 on: May 31, 2022, 10:05:31 AM »

It has been repaired in the past and not aligned properly.
The slide had a couple of links in it.
The base of the reed block had a crack in it, glued up with some brittle clear glue, very different from the usual brownish stuff.
Now it's going to be interesting getting it back together.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Rewaxing 4-stop Hohner.
« Reply #16 on: June 02, 2022, 09:17:48 AM »

It turned out that the base of the block where the slide works was uneven and the air could leak along this.
As this was a HA113 for a friend I couldn't risk it coming back to me. It had to be a proper final repair, not a make do for myself.
I slowly and very gently rocked the block until the the glue gave way and then I could flat it on a long standing block.
I took this opportunity to make sure the wax was ok
I was terrified to think I'd do all the work and there would still be an air leak so I made a very bodgy attempt to hold it in final position and confirm it seated properly. Second time it worked after removal of a stubborn bit of glue and I was able to play it.
I then glued up and used the same Heath Robinson system to hold it .
Success!!
« Last Edit: June 02, 2022, 09:40:58 AM by Squeaky Pete »
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Rewaxing 4-stop Hohner.
« Reply #17 on: June 02, 2022, 09:35:49 AM »

Necessity being the Mother of invention, well done!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Rewaxing 4-stop Hohner.
« Reply #18 on: June 02, 2022, 03:52:41 PM »

“ I slowly and very gently rocked the block until the glue gave way...”

I have never achieved this, always been too wary of damaging the delicate slide cut outs!

I must say “ Well done!”
Logged

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Rewaxing 4-stop Hohner.
« Reply #19 on: June 03, 2022, 10:29:05 AM »

An old 3 stop of mine, with the single reedset block being removable.
(Posted on here in the past - Credit to P.Grassby of Coventry.)

Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal