Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Reeds behaving badly  (Read 2025 times)

0 Members and 1 Guest are viewing this topic.

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Reeds behaving badly
« Reply #20 on: October 19, 2022, 09:49:43 AM »

I did all this when preparing the reeds.
I strip them of old wax and glue and let them soak for a day in old acetone. I then take then out, roughly brush any crud off and drop them in clean acetone for an hour or so to get off any remaining debris.
I brush them clean with a soft brass brush then pre tune, checking for alignment, loose rivets etc. In old Hohner boxes about 20% seem to need attention and that might mean repositioning the blade to even out the clearance, filing one side or the end, resetting the rivet. I like to do it at this stage as once it's been waxed in it's a right pain.
I used to be quite cavalier about tolerances, but I've learned not to be too impatient.
So I'm pretty sure there was no fault in the reeds themselves.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reeds behaving badly
« Reply #21 on: October 19, 2022, 09:51:45 AM »

I agree with mselic (and notwithstanding the previous comment)… If they are the original reeds I’d assume all the internal block geometry is fine and but I’d remove the offending reeds and check the alignment and performance on a tuning table and with a bright light. You'll be able to see if the reed is closer to one side than the other or if there are high spots.
« Last Edit: October 19, 2022, 09:54:00 AM by RogerT »
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Reeds behaving badly
« Reply #22 on: October 19, 2022, 10:13:28 AM »

ive had similar issues where the inside reed valve is catching the reed or catching the chamber wall or where the reed itself is catching the chamber wall.....all can be eliminated by taking out the reeds and checking....if they are the bigger reeds leather valves can help possibly trimmed in width as sometimes the inner layer on plastic valves can distort and catch the reed or the chamber wall. if you take the reed out by running round the edge with a scalpel you'll be able to check one thing at a time by temporarily replacing the reed in the old wax.....once the solution has been identified you can do a proper rewax. it may be that you have more than one problem.....valve issues are often the cause of variations in pitch especially on inside reeds.
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Reeds behaving badly
« Reply #23 on: October 19, 2022, 01:18:24 PM »


     Question   (as proprietor of the “21st Century Box” thread)

    Are there any lessons for contemporary makers to be gleaned from the problems with these older designs?
Logged
  _       _    _      _ 

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reeds behaving badly
« Reply #24 on: October 19, 2022, 01:31:59 PM »

In the case of the Hohner Cajun box. Don’t glue in two upright reed blocks… (:) It’s profile is this 'AA' rather than this '_A_'
« Last Edit: October 19, 2022, 01:33:40 PM by RogerT »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reeds behaving badly
« Reply #25 on: October 19, 2022, 02:22:13 PM »

In the case of the Hohner Cajun box. Don’t glue in two upright reed blocks… (:) It’s profile is this 'AA' rather than this '_A_'

Well no, that would make it a different instrument.  Lay two reed banks flat and you need a significantly larger box.  The genius of the 114 with its two upright blocks is that is light and compact.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Reeds behaving badly
« Reply #26 on: October 19, 2022, 02:40:21 PM »

Fixed.
I lifted the outboard end of the reedplates and slipped a (relatively thick, at 0.5mm) veneer under the 3 offenders, then re-waxed.
The two higher ones were perfect and the biggest one still just bottomed out. I prized it up again, outboard end only, and slipped another sliver of veneer in. Again re-waxed and it seemed much better. Still bottoming out but at quite high volume.
So I tried with all reeds working and I couldn't repeat the fault.
Interestingly, if you are so inclined to read further, I checked the depth of the chambers in a LMM PA reedblock of similar vintage and the narrow end  was 9mm for the largest and lowest reed.
In the 113, the space is 8.5mm and the pitch is lower than the lowest on the PA. That seems to confirm in my mind that an increase of around 1mm should allow the correct clearance.
Which brings me back to my original point, why didn't Hohner spot the problem and fix it? It not a really old box, it has a plastic keyboard.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reeds behaving badly
« Reply #27 on: October 19, 2022, 03:09:45 PM »


Which brings me back to my original point, why didn't Hohner spot the problem and fix it? It not a really old box, it has a plastic keyboard.

Perhaps they did fix it in later examples, and in the 114?   It could be the particular set of reeds.  I'm speculating here!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Reeds behaving badly
« Reply #28 on: October 19, 2022, 04:09:11 PM »

Congratulations!
Having read about your pre-assembly efforts, your detailed attention to cleaning and checking, that must have been very frustrating.
Onwards now to a few tunes and...the next box!


Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reeds behaving badly
« Reply #29 on: October 19, 2022, 08:20:15 PM »

In the case of the Hohner Cajun box. Don’t glue in two upright reed blocks… (:) It’s profile is this 'AA' rather than this '_A_'

Well no, that would make it a different instrument.  Lay two reed banks flat and you need a significantly larger box.  The genius of the 114 with its two upright blocks is that is light and compact.

You could still make them removable blocks in the “AA” arrangement. I believe the Castagnari Max is like this. The idea that reeds laid flat are more responsive sounds right, but in practice I’ve never noticed a difference in response or volume between the upright and flat blocks in a Cajun-style box. In fact, the loudest and most responsive boxes I’ve tried actually have the two outside blocks angled upright, nearly the same as “AA”.
Logged
C#/D player

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Reeds behaving badly
« Reply #30 on: October 20, 2022, 10:30:19 AM »



My old Castagnari Lily had its reeds laid flat and was incredibly responsive. But as I moved onto larger kit, I learned that a good maker can do the same with 2 or 3 blocks of raids in the A pattern described above.

I think a lot of the sense of response in the Lily was due to its small bellows, which generate a sense of fast response with large pressure changes for little effort in your left arm. But the single reeds were genuinely fast too …

My present 2 Melodeons are both 3-row, with reed blocks. But I have to say that I have never experienced the … delinquency described in the original post here. So it seems likely that there is some design fault underlying that,  which was the reason for my query above
Logged
  _       _    _      _ 

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reeds behaving badly
« Reply #31 on: October 20, 2022, 02:26:09 PM »

I should have clarified that, in my last example of Cajun-style boxes, the angled upright reedblock arrangement would have looked more like “\A/“.
Logged
C#/D player

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Reeds behaving badly
« Reply #32 on: October 20, 2022, 03:48:20 PM »

Quote
Are there any lessons for contemporary makers to be gleaned from the problems with these older designs?

If we're talking about the problem of insufficient chamber depth, it's interesting to note that many of the older designs were more sophisticated/complicated than current ones in this area, with depth decreasing from low to high reeds, versus the now-prevalent uniform depth.  So the old makers would have been well aware of clearance requirements.  Nothing wrong with this older design (IMO), but it has apparently been found to be an unnecessary complication.




Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reeds behaving badly
« Reply #33 on: October 20, 2022, 09:15:34 PM »

Quote
Are there any lessons for contemporary makers to be gleaned from the problems with these older designs?

If we're talking about the problem of insufficient chamber depth, it's interesting to note that many of the older designs were more sophisticated/complicated than current ones in this area, with depth decreasing from low to high reeds, versus the now-prevalent uniform depth.  So the old makers would have been well aware of clearance requirements.  Nothing wrong with this older design (IMO), but it has apparently been found to be an unnecessary complication.

I’ve seen it on new, Italian-made boxes.
Logged
C#/D player

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Reeds behaving badly
« Reply #34 on: October 22, 2022, 08:18:26 PM »

Finished tuning today. The lowest reeds sound fine with everything sounding though being so low, they are a bit slow to speak.
I rather like the sound of this box, though do I need yet another one row?
I'll do a video shortly.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal