Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Echo - adjusting keyboard travel  (Read 2987 times)

0 Members and 1 Guest are viewing this topic.

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Hohner Echo - adjusting keyboard travel
« on: November 08, 2009, 07:50:50 PM »

Hi,

I'd like to adjust the keyboard so that the keys all sit level when at rest (on or two are a little out of line) and also regularise the amount of travel.  I've had a good look at the mechanism and I'm turning over few ideas but I thought I'd have a trawl on the forum to see what people think.  Especially before I start doing something that might not be easily reversible.

As far as I can determine the buttons are made up from a truncated cone that looks like cork (sort of bucket shaped), with a mother-of-pearl effect button on top, and a felt pad on the bottom of the cone.  The felt pad limits the downward travel, and since some buttons go down further than others I guess that means that those felt pads are differing thicknesses.   The bottom of the keyboard has a strip of some sort of hard felt, or maybe its suede, under the buttons. 

As far as I can see there are two options to set the travel (1) Pack under the the buttons individually to get them each to the desired travel, or (2) Trim down the existing felt until they all travel the same distance, even though that will be too far, then add another layer of something under the keyboard as a limit.   

Any comment on either of these two options?   The reason for wanting to reduce the travel is to reduce the times that the keys rub or click against other parts inside the keyboard, that was getting on my nerves.

Thanks in advance,
Logged
Tony S

graememackay

  • Graeme Mackay
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 596
  • B/C/C# Pleeeeeeeeeeeeeze
    • Graeme's homepage
Re: Hohner Echo - adjusting keyboard travel
« Reply #1 on: November 08, 2009, 11:27:42 PM »

On my echo, I wanted to reduce the travel.  When I opened up the box, I found the cork as you suggested.  I also found that it's pretty fragile, so if you are sliding anything underneath, be careful not to break any of it off.

I just slipped a couple of sheets of paper folded over under my buttons which did the trick.  For those that travelled further, an extra wee bit of paper was used, folded enough times to provide the sufficient height.

This saves any costs and fancy materials.  If done right it helps get rid of any clattering noises too.
Logged
Black Shand Morino

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Hohner Echo - adjusting keyboard travel
« Reply #2 on: November 09, 2009, 08:31:13 AM »

Cheers, and special thanks for the warning on the cork.  I'll go gently.   As a temporary trial I've slid a strip of felt under the middle row.  That's perfect for most of the keys, but for a few it doesn't allow enough travel and you need to press hard on the key to squash the felt before the note sounds.

Any suggestions on adjusting the "at rest" key heights?   Options appear to be either (gently!!!) bend the metal levers a little to raise the button.  Or remove the mother of pearl key and pack between it and the cork, although I'm not sure what holds that together at the moment. 
Logged
Tony S

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Echo - adjusting keyboard travel
« Reply #3 on: November 09, 2009, 08:41:23 AM »

The 'proper' way of doing this is to bend the levers.  If the levers are aluminium its done by squeezing one edge of the lever with a pair of plier like tools with rounded face to the jaws.  With steel levers on small hohners the only way I know of is to hold the pallet down and push the button down or up. Its a bit brutal either way so go carefully.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Hohner Echo - adjusting keyboard travel
« Reply #4 on: November 09, 2009, 08:52:34 AM »

Thanks for that Theo.  The buttons need to move up a little, and I think I can work out how to apply that bending force so that it can't overdo it.
Logged
Tony S

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Hohner Echo - adjusting keyboard travel
« Reply #5 on: November 09, 2009, 10:39:24 AM »

For increasing the travel I found it easier to push the button down to its limit and then carefully pull back the pallet arm so that when the pallet returns to position the button is now higher up. Is there a reason you would do it the other way Theo? It seems just as brutal either way.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Echo - adjusting keyboard travel
« Reply #6 on: November 09, 2009, 10:51:28 AM »

That method works exactly the same in my experience.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal