Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed Plate types in old Hohner accordions  (Read 1578 times)

0 Members and 1 Guest are viewing this topic.

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Reed Plate types in old Hohner accordions
« on: March 14, 2023, 08:15:09 PM »

Hi all, I am just on the lookout for a cheap old PA, so that I have some spare reeds to play about with for accidentals and so on. Ideally I’m looking for aluminium plates and was wondering when the switch from Zinc to aluminium occurred, and more specifically whether you think an old Carmen II 24 bass accordion would have Zinc or Aluminium plates inside (it has a celluloid finish and could date any time from 30s as far as I know)?.. Thanks
Logged
Dancing about architecture since 1997

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reed Plate types in old Hohner accordions
« Reply #1 on: March 14, 2023, 09:28:55 PM »

Why are Aluminium plates more desireable?

I strongly suspect the answer is when Aluminium became cheaper than zinc.....and when the metals markets rose and fell out of sync there may well have been a time when sometimes batches of Aluminium plates came out followed by batches of zinc....post war Al was always cheaper.
Logged

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Reed Plate types in old Hohner accordions
« Reply #2 on: March 14, 2023, 09:33:25 PM »

Not necessarily more desirable per se, just a matter of better matching them to other aluminium reedplates already in the melodeon to which they would be transferred. Good points, yes that makes sense about economical considerations…
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed Plate types in old Hohner accordions
« Reply #3 on: March 14, 2023, 09:59:41 PM »

I don't think there is a foolproof way to tell without looking inside.  Many Hohner models were produced for many decades, so if you can develop an eye for the design features that relate to age that can help.  I'm pretty sure that they used zinc and ally types at the same time in different models, and it's also common to find zinc in the right side and ally in the left, and even a mix on the same reed block.

An added complication is that ally reeds are not all the same. Early ones are similar in sound and response to zinc, some are marked H, some T and there are also "T." which can be slightly different from T and the H can be a broad H or a narrow H.  The broad H are usually a little more responsive, but it's all a very complex minefield.  And there are more types that I've not mentioned.

The best advice I can give is just to get hold of the cheapest old Hohners you can find and hope the reeds are not rusty!  Don't worry too much about mixing zinc and ally.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Reed Plate types in old Hohner accordions
« Reply #4 on: March 15, 2023, 01:48:31 PM »

Good advice Theo, thanks! One thing I have definitely noticed is you can’t necessarily tell much about the state of the reeds from the general state of the box!.. Interestingly, the 1040G I’ve been playing around with has a mix of wide and narrow ‘H’ stamps on its plates.
Logged
Dancing about architecture since 1997

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Reed Plate types in old Hohner accordions
« Reply #5 on: March 15, 2023, 02:56:57 PM »

Why are Aluminium plates more desireable?

He doesn't want one reed that sounds better than all the others ; )
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reed Plate types in old Hohner accordions
« Reply #6 on: March 15, 2023, 05:18:40 PM »

If it’s an oldish Hohner Student (not the 1930s ones…later than that) and the tuning is generally badly off, esp on the bass end, then the reeds quite likely have corrosion down near the rivet.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal