Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner One-Row ha112/3/4 button limiting  (Read 778 times)

0 Members and 1 Guest are viewing this topic.

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Hohner One-Row ha112/3/4 button limiting
« on: October 18, 2023, 08:55:10 PM »

Hi all, I was trying to find info on limiting button travel on the old Hohner one-row but couldn’t find what was looking for, so I came up with my own solution that I thought I’d share…

I cut ten 15mm lengths of 6mm square dowel, which I then lined up on a strip of double sided tape before cutting out neatly with a craft knife. Having taken the backing from the tape, I carefully placed each length of dowel under its lever using some tweezers and a steady hand!.. I then pushed the button down to securely position the piece of wood in place. With still a little too much travel in the buttons, I finally wedged little strips of felt between the lever and dowel and this finished the job off nicely. I haven’t attempted to take the keyboard off yet, so not sure if this is possible without removing the wood strips, but anyway not too permanent since I used double sided tape!..

I also found a nice thin wine cork and used this to limit the left hand spoons (I call these bits of cork spring-savers since I’m assuming this will reduce the likelihood of spring breakage!?..), although that’s an idea I had seen before elsewhere…
Logged
Dancing about architecture since 1997

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Hohner One-Row ha112/3/4 button limiting
« Reply #1 on: October 19, 2023, 05:23:30 PM »

That’s a decent modification. Thanks for sharing.
Using the same ‘limiting’ position, it is possible to introduce a complete strip at the same time as the action is being reintroduced into the fingerboard.
It can be a bit fiddly and usually requires more than one attempt to achieve the desired button height.
Logged

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Hohner One-Row ha112/3/4 button limiting
« Reply #2 on: October 19, 2023, 07:21:11 PM »

Thanks, that’s good to know, I will attempt the other way next time!.. I figured out that the optimum height for a strip without the felt would be 1/4” (optimum for me being where the top of the button dome goes down to level with the flat of the fingerboard), a bit wider than 6mm but that’s what I had laying around and the felt is a good clack reducer…
Logged
Dancing about architecture since 1997

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Hohner One-Row ha112/3/4 button limiting
« Reply #3 on: October 21, 2023, 11:07:30 AM »

For limiting the spoon action I buy 3/4” plain rubber ball valve washers and hold them in place with a dot of BluTac. They sometimes move about a bit in warm weather but otherwise work very well for a ten second fix and are extremely durable.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal