Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Reedblocks and their effect on tone  (Read 2744 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Reedblocks and their effect on tone
« on: April 11, 2025, 05:36:11 PM »

I've done a lot of research over the years on how reed response, tone, volume, etc are impacted by the various factors when installed in an instrument.  This has sometimes involved me doing things that most (sane) people wouldn't bother with, such as cycling through entire sets of different reed makes on the same blocks in the same instrument at different times, back-and-forth, and then traded with other instruments, back-and-forth, etc.  It's allowed me to isolate certain factors to get a better idea of the particular qualities of a given make of reed and how it behaves under certain conditions/environments.  These experiments have been very instructive, but also sometimes raise more questions than answers...!

In my shop this week I had two of my own accordions that were essentially the same model built in the same key, only about 20 years or so apart (One was built in 2020 or so, and the other in the late 90s).  The overall design and dimensions are the same, with a few minor differences.  The reedblocks are interchangeable, with the foot/base of the reedblock identical between the two, with the same sized openings, same spacing, etc.  While the foot of the reedblocks are the same, the design of the reedblocks themselves are very different.  They're angled differently, they taper differently, but most importantly the reedblock chambers - for the same notes on each instrument - are different sizes.  On the newer block the chambers are shallower with a groove cut out to accommodate the swing of the inner reed, while the older block has straight-cut/squared-off chambers like you'd find in a Hohner.  The volume of each chamber on the new block is therefore reduced in comparison to the corresponding note on the older block.

Here's where it gets interesting.  I took a block out from each instrument, stripped of reeds, and then proceeded to sound the *same* reed (pressed into some remaining wax to seal any gaps) on each block in the corresponding chamber on a tuning bellows.  So to be clear, I took one reed and pressed it into the wax on one block, sounded it on the bellows, then took the exact same reed and did the same with the other block, back-and-forth to compare.  What was immediately apparent was that the volume, response/feel and more importantly the TONE/TIMBRE of the same reed was different on each block.  On the newer block with shallower reed chambers, the volume was a little less, the tone a little more refined, and the push/pull response and feel of the reed a little more 'free'.  On the older block with larger volume reed chamber, it was noticeably louder, the tone a little harder, and the push/pull response and feel of the reed a little more tight/harder. Note that in each case, the reeds responded immediately with the slightest amount of pressure, so it wasn't a case of adjusting the voicing/gap between blocks.  But how *freely* the reeds felt in that push/pull dynamic - which is so integral to diatonic boxes - was different between the two.  I experimented with different reeds tried out in their corresponding chambers, as well as the adjacent chambers, and the overall differences between the blocks remained consistent.

Now, the reedblocks were also made of different materials, but I know that's a contentious topic so I'm not suggesting that was a factor.  I actually can't isolate that factor with these blocks, so couldn't say one way or the other.  I did try placing some shims in the older block, but the only real difference that I noticed was *maybe* a slight reduction in volume.  Anyhow, the thing that struck me the most was that the TONE/TIMBRE was different between the two.  Yes, you could certainly recognize the inherent sound/character of that particular reed on both blocks, but there was a noticeable difference, subtle but profound. This difference certainly translated when reeds were actually installed on blocks and played in the instrument.

Fascinating!
« Last Edit: April 11, 2025, 05:41:56 PM by mselic »
Logged
C#/D player

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reedblocks and their effect on tone
« Reply #1 on: April 11, 2025, 06:22:24 PM »

Thank you - I think it's important for luthiers to share their observations. But I wouldn't jump to any conclusions, as I can offer some contradictory observations.


Observation 1: Italian 1- and 2- voice accordions are about as harsh as wiping ones backside with 80 grit sandpaper, when you compare them to Russian or German designs. I hear a lot of very high, unpleasant partials in the sound. However, Italian boxes are the ones that typically have tiny "grooved" chambers you describe as "small". Russian and German usually have large, "boxed" reed chambers.
Professional Soviet bayans are about as smooth as non-cassotto squeezeboxes ever get, yet, they have the largest chambers compared to anything else. I had a bandonion and old hohners with squared off chambers that I would rate as a lot smoother than anything that comes out of Italian factories.
Russian factory-made jobbies are a lot harsher-sounding than the pro-grade bayans. Very different reeds in similar square chambers.
As a minimum, I would conclude that if chamber design has any noticeable effect on timbre, it's secondary or even tertiary to the reeds and other factors.
To re-phrase, if small grooved reed chambers have a dominant effect on timbre, Italian boxes would be the smoothest regardless of the reeds, yet, they are observed to be the harshest.

Observation 2:
I've re-performed the experiments described on musiker.de board, where you make an adjustable volume reed chamber and you can tweak the chamber volume even as you're sounding the reed. You could vary the volume 6x in a matter of a couple of seconds. Caveat: You do not really vary the shape of the chamber, e.g. internal tapers. Just internal volume.

Results were as follows (perfectly in line to what was reported on musiker.de by other testers):
1) Timbre: Almost no difference overall. Some octaves had no effect at all, others had trivial effect on timbre, with a barely noticeable change in high harmonics. From memory, large volume highest harmonics sounded a bit more like "o" while smallest chambers sounded more like "a". We're really splitting hairs here. 6.05 and half a dozen.
Change in timbre would not pass a blind test over the whole range, imho.

2) Loudness: It's not so much about big vs small, it's about the reed chamber internal volume vs the reed pitch. You can find the chamber volume where the reed is choked (in extreme cases, a perfectly set up reed wouldn't start at all, no matter the air pressure!). You can find "wolf" note volumes where the reed is at its loudest. Significantly louder than the rest of the reeds. I did not devise any mathematical formula to predict the "dead" and "wolf" points.
I found that for piccollo range, making chambers about 4 times bigger than what you see in Italian boxes makes those piccolos sound louder and start up with the lightest effort. As you increase the volume, the loudness (and response) changes from low to high back to low back to high, etc.
To re-phrase, for piccollo ranges, Italians got it all wrong. But their main objective seems to be to pack as many reeds into a small box, as humanely possible, so I suspect that reed chamber design comes down to the smallest reedblock footprint.
Loudness and ease of response go hand in hand with "wolf" chamber volumes. I.e. you can't get quieter, but better response combination by varying the volume. Quiet+hard to start or louder+easier to start only.

One last thing to note, if you are just pushing the reeds into old wax, the reed can be gripped with different strength, which can significantly distort your observation results. A reed plate that's firmly held to the block responds very differently to a reed plate that's barely held down.

What is surprising here, is that we are getting different results when performing similar-ish tests, which suggests that we are not isolating the factors well enough.
« Last Edit: April 11, 2025, 06:42:01 PM by mChavez »
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedblocks and their effect on tone
« Reply #2 on: April 11, 2025, 06:46:10 PM »

To be clear, the only observations that I drew from this was the different reedblocks *can* have an effect on volume, response and tone for the same reed (and clearly did in my case) but nothing specific beyond that.  I simply shared my observations, but I'm not suggesting that shallower reed chambers always = more refined tone, only that in my specific case the block with shallower chambers happened to create a more refined tone than it's corresponding block with larger chambers for the exact same reed. I'm not pinpointing a specific factor and claiming that it's the cause, but rather pointing out the differences between two blocks that created the differences in the reed I described, isolated from the instruments themselves.

Quote
As a minimum, I would conclude that if chamber design has any noticeable effect on timbre, it's secondary or even tertiary to the reeds and other factors

People seem to make hard-and-fast statements like this all the time, rather than saying that from their experience they were not able to detect any difference, etc (maybe that *is* what you're saying here). What people hear with their ears is not as objective as we like to think.  My son is a trained musician with a good ear for music, but he can't really tell the difference in timbre of two accordions that I have that sound completely different to me.  In my example with the reed on blocks on tuning bellows, I could certainly hear a difference (let alone how they feel in the push-pull dynamic), but it's quite possible your ear or someone else's ear wouldn't pick up the same difference.  To me there's no question that the sound, volume and feel of the reeds is different for the same reed between the two blocks in my experiment.  Taking them out of the instrument was my attempt to remove as many other factors as possible, bringing it right down to the blocks themselves.  From my experience, at least in this particular case, the BLOCK itself (whether that has to do with reed chamber size/volume, design, materials, finish, etc) made a difference for the same reed.  There's something to that.
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedblocks and their effect on tone
« Reply #3 on: April 11, 2025, 06:48:28 PM »

Quote
One last thing to note, if you are just pushing the reeds into old wax, the reed can be gripped with different strength, which can significantly distort your observation results. A reed plate that's firmly held to the block responds very differently to a reed plate that's barely held down

I properly waxed them in afterwards just to be sure it wasn't a factor.  It wasn't.
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reedblocks and their effect on tone
« Reply #4 on: April 12, 2025, 12:42:37 PM »

If you 'listen' with a sound analyser, which shows frequencies/partials on a graph, would this be an 'objective' measure if the differences you can hear but your son cannot? Just curious.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reedblocks and their effect on tone
« Reply #5 on: April 12, 2025, 01:00:06 PM »

I've done some analysis with VA analyser (which I've used successfully for guitar lutherie in the past) and I didn't get anywhere with squeezeboxes - there's nothing obvious that was jumping out when comparing very different-sounding boxes.
I suspect that the lower spectrum is pretty much the same for all reeds and it's the higher frequencies where the differences happen.

Somebody might have had better luck.
Logged

Steve C.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2075
  • Erica, Morse Anglo
Re: Reedblocks and their effect on tone
« Reply #6 on: April 12, 2025, 03:56:25 PM »

Chavez, you are harsh.
But the truth of the Italian 2-voice box, hurts....
Logged
Located in Central North Carolina, USA; credit for picture: livingplanet.ca

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedblocks and their effect on tone
« Reply #7 on: April 12, 2025, 05:17:04 PM »

Chavez, you are harsh.
But the truth of the Italian 2-voice box, hurts....

I'm not sure that's a fair claim...the tone of Italian accordions runs the gamut from harsh to sweet!  There are some Castagnaris that have a very sweet tone indeed (in fact, that's the very reason why some in the ITM box community shy away from them - the sound is a little too gentle!).  The number of different diatonic boxes made in Italy is staggering and I think it's a very broad statement to make suggesting they all sound harsh!
Logged
C#/D player

Steve C.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2075
  • Erica, Morse Anglo
Re: Reedblocks and their effect on tone
« Reply #8 on: April 13, 2025, 01:10:10 PM »

Matt, do you have an opinion on which Italian boxes "tend" towards sweetness? (brand, model?)
My Laura AD: medium harsh in A, sweet in D
Previous Tommy DG: harsh in two voice, awful. Nice in three voice.
Lilly DG.  Goes without saying.
Logged
Located in Central North Carolina, USA; credit for picture: livingplanet.ca

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Reedblocks and their effect on tone
« Reply #9 on: April 13, 2025, 01:46:08 PM »


   All dynamics of playing reeds, and much of the sweetness of tone lies in the higher harmonics - up to 16kHz.

   As such I've long longed to see some Fourier transform information about … steady state notes,  2 or 3 reeds,
   and the "attack" phase as you press a key or increase bellows pressure.

   Anyone got this "clever" stuff.
Logged
  _       _    _      _ 

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reedblocks and their effect on tone
« Reply #10 on: April 13, 2025, 02:58:42 PM »


   All dynamics of playing reeds, and much of the sweetness of tone lies in the higher harmonics - up to 16kHz.

Where are you getting this information?
The sound of a circular saw cutting wood is packed with higher harmonics, yet, most people wouldn't call it sweet, and Bach decided not to write a concerto for it. Though he didn't write for the 2-voice Italian melodeon either - come to your own conclusions  >:E
If you refer to, for example, Trevor Gore's monumental work on acoustics of contemporary guitars, the luthier is trying to balance the inherent harshness of higher harmonic content (the lower, the sweeter) with the instrument's ability to project (that declines with a reduction in higher harmonic content). All of his observations and modelling tracks with my experience of building guitars and mandolins.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedblocks and their effect on tone
« Reply #11 on: April 13, 2025, 02:59:38 PM »

Matt, do you have an opinion on which Italian boxes "tend" towards sweetness? (brand, model?)
My Laura AD: medium harsh in A, sweet in D
Previous Tommy DG: harsh in two voice, awful. Nice in three voice.
Lilly DG.  Goes without saying.

Now this really *is* going to get subjective! I’ve had boxes that I’ve thought sounded incredibly harsh that others thought sounded quite pleasant, so I imagine we’ll all interpret these things differently.

As a *generalization*, I tend to find Castagnaris sound sweet and somewhat ‘polite’. I briefly owned a Tommy in GC years ago and found it had a very sweet tone, not harsh at all. I have a Manfrini Bosca Ceoil in C#/D that I find has a rich, mellow tone completely unlike any of my other boxes in the same key with the same tuning (Manfrini Accordions are based in Scotland but made in Italy). Some of the 2v Beltunas that I’ve tried had a really sweet and mellow tone as well. 

I have two Serenellinis, each of which has had different reeds in them. The reeds make a difference, but one I find has an inherently gentler, more refined tone and the other I would describe as having a harsher, more strident tone, regardless of reeds used.  Italian-made, both (obviously).

I also find, as another generalization, that the lower pitched boxes tend to sound sweeter than higher pitched ones. The kind of reeds in a box can make a big difference (although it’s not always as big a difference as one might expect) as can the pallet arrangement. There can be a substantial difference in tone between the rows depending on the design. I also find the same box can sound alternatively sweet and harsh depending on context, where it’s being played and whether on its own, with others, etc!
Logged
C#/D player

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Reedblocks and their effect on tone
« Reply #12 on: April 13, 2025, 04:30:29 PM »


   To be objective, the human appreciation of a vibrating strip of metal, with complex physical properties, set in a (roughly) resonant physical chamber, dynamically coupled (to some extent) to similar vibrating metal strips of very similar metal ±1 octave in fundamental frequency is a very subjective matter.

  Nevertheless it is a physical process, a sound, and as such subject to for Fourier analysis. Both dynamically, and as a resonant process.

  We have debated the subjected, human reaction to a vibrating free read endlessly in this group. But beneath that there is a natural physical process,  Modern computer science is very capable of shedding light upon what actually happens. I am simply seeking to set some light on what is in effect … a matter of opinion.
« Last Edit: April 13, 2025, 04:33:41 PM by Chris Ryall »
Logged
  _       _    _      _ 

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Reedblocks and their effect on tone
« Reply #13 on: April 13, 2025, 09:17:44 PM »

Thanks Matt it's most instructive. It seems to concur with what many makers of accordions I talked to, and also reed makers, presume about what's important.

Observation 1: Italian 1- and 2- voice accordions are about as harsh as wiping ones backside with 80 grit sandpaper, when you compare them to Russian or German designs.

I'd have the exact reverse observation, at least if we're comparing in general Italian and German boxes, albeit with a more nuanced view. I often find that German boxes have a more crisp sound than the average Italian boxes I can hear around here. But as was already said, it's very difficult (if not impossible) to make as general an assumption than that when speaking about these things.

I become more and more convinced (although without any quantitative proof behind it) that the main pitfall of discussions about what's important for how an accordion sounds is to be focused on one parameter, knowingly or not.
When I ask some makers I know that took the time to make numerous comparative tests, I always have the feeling that they tell me that the parameter I asked them about is not really relevant (the notable exception being the reed and the reed chamber).
Perhaps it would be beneficial to adopt a multi-factorial approach to all this. Which is sadly even more difficult to apprehend than a single factor approach.

Steve C.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2075
  • Erica, Morse Anglo
Re: Reedblocks and their effect on tone
« Reply #14 on: April 14, 2025, 01:17:56 PM »

Interesting that you mention the Beltuna.  I played a Beltuna Sara 2 voice DG that I really liked.  Very mellow.  I don't think it had fancy reed set or anything. Seemed a nice box.  Was at the US Squeeze-In a few years back.
It was kind of "flat" in that it did not seem to have overtones.  Seemed like a more refined Hohner Morgane. Maybe? I mean that in a nice way for both boxes.
Logged
Located in Central North Carolina, USA; credit for picture: livingplanet.ca

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedblocks and their effect on tone
« Reply #15 on: May 06, 2025, 11:56:45 PM »

Time for an update!  So, for a quick recap:

I had two of the same model of box (same key right from factory), one was made recently and the other over twenty years ago.  Older one had reedblocks with larger volume chambers, and the newer one had much shallower chambers.  The same set of reeds had a 'harder' sound in the old box (larger chambers) and a more refined tone in the newer box (shallower chambers).  The difference was also noticeable with the blocks isolated outside the instrument.  Anyone interested can read the original post above.

Following a hunch, I decided to install shims in all of the reedblock chambers of the old box to match the approximate design/volume of the chambers in the newer box.  These were cedar shims carefully cut to the appropriate size with one side carved out for the swing of the inner reed, just as in the newer box.  Once everything was done, reeds were installed and tuned and...

PRESTO!  - much of the 'hardness' of the tone of the old box was gone and it now sounded noticeably more like the sweeter, refined tone of the new box!  Same set of reeds, same tuning, but the reshaping of the chambers had a noticeable impact on the tone/timbre of the box!  The response was also different - the newer box had felt a little easier to play, and the older one a little harder, but now the older one with the reshaped chambers responded with more ease as well (and this is not related to reed gap - reeds were set up to respond instantly in each case).  To me, this is hard evidence that the size/shape/etc of reed block chambers can not only impact response and volume, but also the tone/timbre of the reeds.  I've not replicated the process in another instrument (and probably won't any time soon - I have client's instruments I should be working on instead!), but I'm happy to say that it made a noticeable difference for me and I'm quite happy with the result!

Logged
C#/D player

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reedblocks and their effect on tone
« Reply #16 on: May 07, 2025, 01:49:34 AM »

Time for an update!  So, for a quick recap:

I had two of the same model of box (same key right from factory), one was made recently and the other over twenty years ago.  Older one had reedblocks with larger volume chambers, and the newer one had much shallower chambers.  The same set of reeds had a 'harder' sound in the old box (larger chambers) and a more refined tone in the newer box (shallower chambers).  The difference was also noticeable with the blocks isolated outside the instrument.  Anyone interested can read the original post above.

Following a hunch, I decided to install shims in all of the reedblock chambers of the old box to match the approximate design/volume of the chambers in the newer box.  These were cedar shims carefully cut to the appropriate size with one side carved out for the swing of the inner reed, just as in the newer box.  Once everything was done, reeds were installed and tuned and...

PRESTO!  - much of the 'hardness' of the tone of the old box was gone and it now sounded noticeably more like the sweeter, refined tone of the new box!  Same set of reeds, same tuning, but the reshaping of the chambers had a noticeable impact on the tone/timbre of the box!  The response was also different - the newer box had felt a little easier to play, and the older one a little harder, but now the older one with the reshaped chambers responded with more ease as well (and this is not related to reed gap - reeds were set up to respond instantly in each case).  To me, this is hard evidence that the size/shape/etc of reed block chambers can not only impact response and volume, but also the tone/timbre of the reeds.  I've not replicated the process in another instrument (and probably won't any time soon - I have client's instruments I should be working on instead!), but I'm happy to say that it made a noticeable difference for me and I'm quite happy with the result!
Interesting Matt, did you take measurements for the depths of the chambers? I don’t see it mentioned anywhere here but I might have missed it.  And are the chambers even top to bottom or tapered having less space at the top of the chamber?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedblocks and their effect on tone
« Reply #17 on: May 07, 2025, 03:47:13 AM »

I didn't write down any measurements, but I was measuring them as I was working, matching the older blocks to the new ones as closely as possible.  I wanted to make sure that each of the inside reed tongues had enough clearance, as well as ensuring the adjacent valves had enough room to open sufficiently.
« Last Edit: May 07, 2025, 04:00:10 AM by mselic »
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedblocks and their effect on tone
« Reply #18 on: September 04, 2025, 06:29:32 PM »

Just wanted to update this thread with some additional information.  I recently did some more experimenting with adjusting reedblock chamber sizes and how they affected tone, volume and response.  I also built my own reedblocks for a particular instrument so that I could experiment further.  Any comparisons were always done with the very same set of reeds fully waxed and tuned (same tuning) into the same instrument.

Once again, there were a very clear and discernable difference in tone/timbre, volume and even reed response when reed chambers were reduced in volume (area) with cedar shims.  I was surprised to notice a difference even with very thin cedar shims that were only 1mm or less (tapering down to zero at the bottom of the chamber).  I have no idea if the type of wood used for the shims makes any difference (apparently, it shouldn't) - I only used cedar because it was a softwood that was easy to chisel and shape.  When the chambers were reduced in size with the shims, the tone/timbre became softer/sweeter but the volume was noticeably reduced.  It also took less initial effort to get a reed to respond, but that also translated into ornamentations (particularly things like trills) feeling different.

All this to suggest that there's quite a bit to be said about reedblock design and how it affects the sound you get from an instrument.  I've heard it suggested on here before that reedblock chamber size doesn't make a difference, that it's only about giving the swing of the reed tongue enough clearance, but I'd say this is evidence to the contrary!
« Last Edit: September 04, 2025, 06:38:53 PM by mselic »
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedblocks and their effect on tone
« Reply #19 on: September 04, 2025, 06:54:39 PM »

Here are two videos showing the same reeds, same tuning in the same instrument, the only difference being in one there are 1mm cedar shims lining the chambers (reducing the overall size of the chambers), and in the other there are none.

Without shims:

https://youtu.be/pewLaWp0Yg8

With shims:

https://youtu.be/a831slIqZtY


The differences are not as obvious on a poor quality phone recording as they are in person, but to my ears there is still clearly a difference in overall tone/timbre (I've often found that such differences are much easier to detect with one's ears in-person, whereas an iphone audio recording won't always pick up those subtleties).  You'd be best to open both videos in different windows and go back and forth.  I found the example with shims gave the accordion a somewhat softer, more 'rounded tone, whereas the other one is a little brighter/harsher.  The tonal differences are less noticeable with the higher notes.  The difference in volume is also not as apparent in the video but I promise you it's there (you can really notice it if you remove the shims from the chambers for one note, played next to another).  Forgive the playing - the videos were originally just made for me and I had chosen a tune I wasn't entirely familiar with.
« Last Edit: September 04, 2025, 06:57:08 PM by mselic »
Logged
C#/D player
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal