Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: How are reed blocks attached?  (Read 450 times)

0 Members and 1 Guest are viewing this topic.

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
How are reed blocks attached?
« on: June 12, 2025, 01:07:46 PM »

This is related to my previous thread.  Melodeon is a Womack one-row. I don't know the correct terminology for the long, thin slips of wood which are controlled by the 4 knobs at the top and which are supposed to slide up and down to either let air flow through the holes or close off the air flow to the reeds but those pieces of wood are stuck in place. They were tight (hard to slide up and down) when I got this instrument. Maybe humidity swelled the wood to do the rest? I cannot see how the reed blocks are attached to the inside of the treble faceplate. I was thinking/hoping that by removing the reedplates I would then be able to discover how the reed blocks are attached and then remove those to correct the problem.

My guess is that the blocks are glued in place because there is no obvious evidence of screws or nails.

Any suggestions or warnings or instruction on how I should proceed with the work?

And a final comment: I am in awe of the skill and workmanship required to build a single-row melodeon! Taking this one apart (keys were sticking, air was leaking, difficult to open and shut each reed bank) has been an education!
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: How are reed blocks attached?
« Reply #1 on: June 12, 2025, 02:27:26 PM »

One-row reedblocks are most often glued in place. Changing humidity is the most likely culprit in causing both keys and sliders (the wooden strips attached to the stops) to stick. I’m not sure there is much that can be done with the sliders except wait for the humidity to change again…I used to have a 4-stop Hohner that had stops that would be immovable during the winter months, so I made sure they were kept open/up all the time.
Logged
C#/D player

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
Re: How are reed blocks attached?
« Reply #2 on: June 12, 2025, 04:48:27 PM »

Thanks for your response. To me it does seem that the blocks are glued in place. And, instead of doing damage I may as well wait. Or, turn on the dehumidifier for a few days.
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: How are reed blocks attached?
« Reply #3 on: June 12, 2025, 09:25:12 PM »

mmm tricky...hohner sliders are metal so less likely to stick....i use aircarft ply for sliders which i believe is the common practice and kiln dried hardwood for the blocks....yes they are all glued in place.......some makers use graphite powder on the sliders to keep them moving....only thing i can think of is remove wooden blocks from sliders and withdraw sliders completely.....if they are made from aircraft ply try lubricating with graphite powder....if not make new sliders....yes humidy can affect such things so dont store against an outside room wall / try de- humidifiers etc.....finally if blocks are not hardwood maybe make new blocks but getting old blocks out is probably going to wreck the fondo if its all glued up with pva wood glue....try a warm dry room first. if that works you are part way there. maybe get em open and leave em open. not ideal but....
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal