Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4 5   Go Down

Author Topic: Resonance issues with reedblocks  (Read 6930 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Resonance issues with reedblocks
« Reply #40 on: October 03, 2025, 08:45:53 AM »

Blutac  would lead to air leaks under the blocks which would lead to its own problems.

Van der Aa sometimes puts soft rubber washers under the metal strap linking reed blocks in order to absorb unwanted vibrations.  I can’t say I noticed any difference in sound.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Resonance issues with reedblocks
« Reply #41 on: October 03, 2025, 11:50:48 AM »


  Van der Aa also cantilevered the mechanism that moved the pallets so that they all rose a similar distance from the holes. From 2010 or so onwards. I think I posted a video about it in the 21st Century Box thread.

  Could I encourage other members to post any promising innovations there. It is intended as an archive of useful ideas

   https://forum.melodeon.net/index.php?topic=7840.msg206199#msg206199
« Last Edit: October 03, 2025, 11:53:10 AM by Chris Ryall »
Logged
  _       _    _      _ 

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Resonance issues with reedblocks
« Reply #42 on: October 03, 2025, 11:51:07 AM »

Binci reeds are great for Morris, coz they are so f** loud. Will anyone actually notice the wah wah outside? And inside they are horribly anti social.

If that's the intended use for this box, perhaps tuning the reeds to a wider tremolo would stop the problem, since one of the causes of it is having two reeds tuned to almost the same frequency.
A wider tremolo (up to a point) will add to the perceived loudness of the box. May or may not be what you want, of course.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Resonance issues with reedblocks
« Reply #43 on: October 03, 2025, 12:36:41 PM »


  Van der Aa also cantilevered the mechanism

I can't find it in that thread, but I'm sure you've mentioned it before. Would you happen to have any photos of it?
Timing is great - I'm just ruminating over a 4-voice build.

Apologies for offtopic.
Logged

-Y-

  • Hero Member
  • *****
  • Online Online
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Resonance issues with reedblocks
« Reply #44 on: October 03, 2025, 02:40:59 PM »

promising innovations there
Cantilevered mechanisms in accordion is hardly an innovation. It's useful, but it's not innovative.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #45 on: October 03, 2025, 04:38:11 PM »

There's a lot to respond to here, so I'll just start with this:

I built another block and it worked to eliminate the majority of the issues using all Binci reeds (there is still a subtle difference in the beating quality of one F# push note (0 and +) in comparison to it's equally-tuned counterpart (0 and -), but I suspect it's something that a lot of people wouldn't even notice).  It's certainly an improvement on the other blocks.  There are two things that were done differently in this block (I know, I know - that's not a controlled experiment, but it takes a lot of time and effort to build blocks and I've already built three new ones just to play around with this issue).  The chambers were made deeper this time (10mm) and, unlike the original block or the rest of the blocks that I've made, they were made consistently that depth from top to bottom; no tapering of the block.  To avoid clearance issues, I angled the block itself away from the other one.  I can't say that it's the chamber depth or design that made the difference since it's an entirely different block and something in the construction of the block itself may have been the determining factor.  Also, it works about as well as the original, factory-made block does in that most of the resonance issues are removed with the very mild exception of the F# note.  The original block has very shallow chambers with a groove cut-out for the swing of the inner reed, and this new block has deeper chambers.  I've included a photo to show them.

I may include an audio file of the F# note comparisons as well in a subsequent post.  The new block is an improvement in that I'm back to using all Binci reeds, whereas in the other cases I needed to swap out four of the reedplates to eliminate the worst of the resonance issues.
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #46 on: October 03, 2025, 05:14:19 PM »

Quote

No need to apologise - you're very welcome to disagree and I respect you sharing your experience as a fettler. My extensive testing produced no significant timbre variations whatsoever, including changing chamber size while the reed was sounding. So we must be doing something differently. But I never made the chambers so small, that the reeds were no longer performing as they should and there would be a significant deterioration of response.

I've only experimented with two accordions in this regard, using multiple sets of reeds and multiple sets of blocks.  I modified existing blocks by adding cedar shims to reduce the depth of the chambers, and compared the differences (using different sets of reeds as well) with and without the shims.  The results of the reduced chambers done this way were the same when compared with the results from new blocks that I'd built that had shallower chambers by design.  For me, the difference in timbre/tone was apparent even just by sounding the reeds on blocks on a tuning table, but that difference definitely also translated to when the blocks were in the instrument.  I often made a change, waxed and tuned the reeds and played the instrument the way it was for days or weeks, then went back and changed chamber size (re-waxed, re-tuned, etc) and the difference was immediately apparent to me.  I even found that I eventually had to reduce how wide the tuning was with deeper chambers because it sounded too harsh to me.  With the shallower chambers, the same instrument could then take a wider tuning and still sound sweet to my ears.  But I also have a *very* sensitive ear, which can be both a blessing and a curse...

YMMV, of course!

Quote
If you don't mind me asking, what are your thoughts on the bluestars vs vintage Catraros? I'm still tempted to get a set of the latter for a hromka build, given their reputation with Galliano.

I have no idea if the current line of reeds labelled "Catraro" are anything like the vintage Catraros reeds that I've found in old PAs.  I'm inclined to believe they would be different, but I'd be curious to get my hands on a set!  The vintage ones were very long-scale - as long as Binci but not nearly as thin - and are still the best responding reeds that I've ever come across.  This becomes most apparent in the higher-pitched reeds; I've yet to come across a modern reed that has the response and richness of tone once you get to those squeaky notes!  I've replaced the reeds for those top few notes in a couple of my instruments with re-purposed Catraro reeds for that reason.  The BlueStar reeds (the ONE set that I've had experience with) had very poor response for those same, higher-pitched notes.  The only thing I liked about the BlueStar reeds was their tone.  Very rich and full of colour and character!  The only clip I have of them in action is when they were in my Manfrini for about six months:

https://www.youtube.com/watch?v=iLDmiUVREeU
Logged
C#/D player

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Resonance issues with reedblocks
« Reply #47 on: October 03, 2025, 09:22:45 PM »

Thank you.

They do sound very sweet in the video!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Resonance issues with reedblocks
« Reply #48 on: October 03, 2025, 10:59:14 PM »

How does one recognise Catraro reeds?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #49 on: October 04, 2025, 04:25:20 AM »

How does one recognise Catraro reeds?

If you come across an entire set, some of the plates will be labelled "Catraro".  I'll have a look later and see if I can share some photos.
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #50 on: October 04, 2025, 05:05:25 AM »

How does one recognise Catraro reeds?

Here are a few photos of some that I have left (still on the original blocks).  They tend to have large, hammered rivet heads.  The reed tongues are fairly trapezoidal in shape until you get to the lower pitched ones, at which point they become parallel.  The strange thing about them is the inconsistent markings in the reedplate corners; some will have a single horizontal line, others two or three, and others yet will have one short line and second, longer line that crosses the first, all within the same set.  Several of the plates in the same set will be stamped with the "Catraro" name.  I'm not sure if the different markings have any significance for the reed maker or instrument builder, but I've seen photos of other instruments fitted with Catraro reeds and they also featured a mix of these different markings.  You can see more photos of a partial set that Liberty Bellows has on sale here:

https://www.libertybellows.com/shop/c/p/Lot-of-Titano-Royal-Catraro-Treble-Bass-Reed-Blocks-For-Piano-Accordion-Incomplete-x87440615.htm

(If you right-click on the photo and "open in new window" you can zoom in to get a better look).

I've only ever seen these reeds on short blocks like what's shown in the above link.

Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #51 on: October 04, 2025, 05:07:20 AM »

A few more photos:

Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #52 on: October 04, 2025, 05:35:54 AM »

In case it might interest, here’s a sound comparison of three different makes of reeds, one of which is a repurposed set from Catraro, all in the same instrument at different times (all MMM @ approx +-5 cents). The Catraros tend to have a fairly bright sound not unlike Bincis.

Catraro:
https://www.dropbox.com/scl/fi/1w3ev3744sz8bxlc37ye0/Catraro-reeds-comparison.m4a?rlkey=ufv157fnug6fxwgw8aj5tvt18&st=3sxbdsf3&dl=0

Binci:
https://www.dropbox.com/scl/fi/0jfyrxfgpp54pd38cec45/Binci-reeds-comparison.m4a?rlkey=3q8msmhc0x3728eajmlxi657j&st=nzp8uzf2&dl=0

Voci Armoniche TAM:
https://www.dropbox.com/scl/fi/zayyf3592jydmhzlzoyus/VA-TAM-reeds-comparison.m4a?rlkey=4ol3yw2cx8dnqfpzg47q7wh6k&st=3gtktw4q&dl=0
Logged
C#/D player

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Resonance issues with reedblocks
« Reply #53 on: October 04, 2025, 08:19:55 AM »

The strange thing about them is the inconsistent markings in the reedplate corners; some will have a single horizontal line, others two or three, and others yet will have one short line and second, longer line that crosses the first, all within the same set.

This is quite standard markings for PA and CBA reeds to mark the voice. E.g. if you have 3 voices on the flat fondo, they will have 1, 2, 3 marks. "Crosses" could be a voice in cassotto, or just 4th voice on a non-chambered instrument.
If the same voice has a mixture of these markings on its reeds, I'd assume that it was built up from stock leftovers at the factory, or, perhaps, has seen a lot of repairs over its lifetime.

How does one recognise Catraro reeds?
It says so on the proverbial tin ;) Also very distinct rivets, as per mselic's photos.

Hmm. I find that I tend to very strongly favour parallel-sided, smooth sounding reeds over trapezoidal ones, so perhaps these are not for my ears then.

From the recordings (thanks for sharing!) VA TAM seem to have the most middle, but I've had a set of VA TAMs in the past and wouldn't want them again. In my case timbre was very interesting, but a bit sharper that I'd like. Loudness was very high and dynamics were poor, but that's quite typical of TAM.
Bincis seem quite smooth too and don't have the VA's high partial "sharpness", but they don't sound as "juicy" in the middle either.
If Cartraros are brighter, as per the recordings, I'd save myself some cash not trying to hunt them down.
« Last Edit: October 04, 2025, 08:32:10 AM by mChavez »
Logged

-Y-

  • Hero Member
  • *****
  • Online Online
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Resonance issues with reedblocks
« Reply #54 on: October 04, 2025, 11:07:13 AM »

In case it might interest, here’s a sound comparison of three different makes of reeds, one of which is a repurposed set from Catraro, all in the same instrument at different times (all MMM @ approx +-5 cents). The Catraros tend to have a fairly bright sound not unlike Bincis.

Catraro:
https://www.dropbox.com/scl/fi/1w3ev3744sz8bxlc37ye0/Catraro-reeds-comparison.m4a?rlkey=ufv157fnug6fxwgw8aj5tvt18&st=3sxbdsf3&dl=0

Binci:
https://www.dropbox.com/scl/fi/0jfyrxfgpp54pd38cec45/Binci-reeds-comparison.m4a?rlkey=3q8msmhc0x3728eajmlxi657j&st=nzp8uzf2&dl=0

Voci Armoniche TAM:
https://www.dropbox.com/scl/fi/zayyf3592jydmhzlzoyus/VA-TAM-reeds-comparison.m4a?rlkey=4ol3yw2cx8dnqfpzg47q7wh6k&st=3gtktw4q&dl=0

Thanks for the comparison. If it's of any help, I've attached spectrograms.

This and listening to the files confirms Binci are way too bright for my liking. Although they work in some configurations, it's a bit tiring to the ears after some time, I think. I like VA TAM for that, much more presence of the firsts overtones, which feels more soothing.
« Last Edit: October 04, 2025, 11:20:19 AM by -Y- »
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #55 on: October 04, 2025, 01:51:18 PM »

For what it's worth, I found the Bincis to be the easiest playing but harsh, and the Voci Armoniche the sweetest sounding but also the stiffest/hardest.  The Catraros have *incredible* dynamic range, responding with the slightest of pressure but also building in volume without ever choking.  It makes for great playing of slower, expressive music, but they're not my first choice for fast, vigorous playing of a diatonic box (they are, after all, PA reeds).  I ultimately settled on the VA TAM reeds for that box because of their tone at the expense of better reed response.  The Bincis also suffered from a few resonance issues on that box, too....
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #56 on: October 04, 2025, 01:52:37 PM »

Binci reeds are great for Morris, coz they are so f** loud. Will anyone actually notice the wah wah outside? And inside they are horribly anti social.

If that's the intended use for this box, perhaps tuning the reeds to a wider tremolo would stop the problem, since one of the causes of it is having two reeds tuned to almost the same frequency.
A wider tremolo (up to a point) will add to the perceived loudness of the box. May or may not be what you want, of course.

Yes, a wider tuning does appear to eliminate the problem, however it's not the sound I'm after with this box.
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Resonance issues with reedblocks
« Reply #57 on: October 04, 2025, 04:01:16 PM »

 Ah. Right. Well there's the solution  (:)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Resonance issues with reedblocks
« Reply #58 on: October 04, 2025, 04:37:44 PM »

Thanks for the photos of the Catraros reeds.  They look very similar to some old Shand Morino reeds I have.  They have the same style of rivet and they also respond to the slightest pressure and have a huge dynamic range, but I've not seen any makers name on them.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: Resonance issues with reedblocks
« Reply #59 on: October 04, 2025, 05:38:51 PM »

I asked ChatGPT for possible causes of the wah-wah effect. apart from mechanical coupling, it mentioned acoustic coupling, or the coupling of air flows of reeds sharing the same reed chamber. i then asked if the same phenomenon could occur if the reeds were in separate reed chambers but close to another.
This is the answer I got:


Excellent follow-up — and yes, **it absolutely is possible** for acoustic coupling to occur **between reeds in separate chambers** if they are *close enough* and the acoustic impedance between their chambers is not perfectly isolated.

Let’s unpack exactly how and why that happens.

---

## 1. How reeds “talk” to each other through air, even in separate blocks

Even if two reeds are mounted on **different reed blocks**, they are still connected by:

* **Shared air pressure fluctuations** from the bellows and pallets,
* **Mechanical and acoustic leakage** through the walls and openings,
* **Near-field radiation** if their air paths (slots, tone holes, pallet openings) are close in the treble or bass casing.

So long as there is *any* air path — even a narrow gap or a wooden wall that vibrates slightly — the oscillating pressure field from one reed can influence the other’s driving pressure.

---

## 2. Mechanisms of inter-block acoustic coupling

### (a) **Through the common manifold (air chamber / pallet area)**

In many accordions, multiple reed blocks are fed from the *same air plenum* — the area just under the pallets or the tone holes.
When a reed oscillates, it doesn’t only draw steady airflow; it *modulates* the pressure in that plenum. Those pressure oscillations can travel to the neighboring reed block, acting as a *weakly coupled acoustic drive*.

So even if the reeds are in “different chambers,” they can still share a portion of the same fluctuating pressure source.

→ **Result:** a form of *acoustic cross-talk* that can cause correlated beating or strong tremolo if the frequencies are near each other.

---

### (b) **Through the wooden structure (radiation and vibration)**

The wooden reed block walls are **not perfectly rigid** — they vibrate slightly under acoustic pressure changes.
This means one reed’s oscillation can transmit a small amount of vibration through the wood or through the air gap between blocks.

Even if you couple the blocks together physically, if the *mode shape* of the block or casing enhances a particular frequency, it can actually **amplify** the coupling rather than damp it.

→ This can explain why coupling blocks sometimes *don’t fix* the problem — because the coupling is *acoustic, not mechanical.*

---

### (c) **Through the air inside the case (radiated sound pressure)**

At higher frequencies or with reeds that radiate efficiently into the case, **the sound pressure field inside the accordion’s interior** can act as a coupling medium.
Essentially, the case becomes a small resonant cavity. Two reeds close in frequency can exchange energy through this internal air volume, even if their reed chambers are otherwise isolated.

→ This is a *far-field* or *radiative* coupling effect, weaker but still noticeable if frequencies are very close (a few cents apart).

---

## 3. What you’d observe acoustically

If coupling happens across blocks:

* The tremolo may depend on the **relative orientation** of the blocks (direction of air slots and nearby surfaces).
* It might **persist** even if you damp mechanical vibration between blocks.
* The beating strength may **change with bellows pressure** or case resonance (since internal acoustic modes shift with pressure or open/closed grills).
* Sometimes, the phenomenon is **note-specific** — only certain reeds exhibit strong coupling, because their frequencies match a shared resonance of the cavity or block system.

---

## 4. In terms of physics

What you have, fundamentally, are **two self-excited oscillators (the reeds)**, each coupled weakly to a shared acoustic field:

[
m_i \ddot{x}_i + c_i \dot{x}_i + k_i x_i = f_i(p_i), \quad i = 1,2
]
where (p_i) is the acoustic pressure acting on reed (i).

If the chambers aren’t perfectly isolated, then:
[
p_1 = p_0 + \alpha p_2, \quad p_2 = p_0 + \beta p_1
]
where (\alpha, \beta) are small coupling coefficients representing the acoustic cross-talk.

Even small values (on the order of 0.01) can produce **observable beating distortion** or synchronization effects when (|f_1 - f_2|) is small.

---

## 5. Summary

| Coupling path                      | Description                                       | Typical sign                                                      |
| ---------------------------------- | ------------------------------------------------- | ----------------------------------------------------------------- |
| **Air plenum coupling**            | Shared pressure manifold under pallets            | Strong, pressure-dependent tremolo                                |
| **Wood vibration**                 | Structural vibration through reed blocks          | Fixed with stiff coupling, sometimes worsens if resonance matches |
| **Radiative coupling inside case** | Reeds interact via the internal air cavity        | Tremolo persists even when blocks are isolated                    |
| **Nonlinear pressure modulation**  | Shared airflow creates variable coupling strength | Uneven, “wobbling” tremolo                                        |

---

### ➤ So yes:

Even if reeds are mounted on different reed blocks, *acoustic coupling through the shared air volume or resonant casing* can absolutely produce an unwanted tremolo.
When mechanical coupling doesn’t fix it, the culprit is nearly always **aerodynamic or acoustic cross-talk**, not vibration through the wood.





Logged
Pages: 1 2 [3] 4 5   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal