Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Possible nifty tip when fitting hohner springs after refacing pallets  (Read 360 times)

0 Members and 1 Guest are viewing this topic.

Sebastian Trudgian

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 124
  • DG Pokerworks and also play Irish Whistle/Flute

Hi,

I’m a newbie at fettling.

I really don’t like retensioning Hohner springs into their little gaps (they’re fiddly and seem to always stab my fingers when I try to bend them), so was trying to find a way around having to do this in situ.

I believe you’re always supposed to release/refit springs when the pallet mechanism is screwed into the melodeon case… ie never unscrew (or screw) the mechanism from the case whilst the levers are under tension as this will rip the screws out of the threads as they approach the ends of the holes.

However this means you have to refit the springs in a really awkward fashion (it’s much easier to do this when the mechanism is outside of the box)

I was playing and I found it’s very easy to sequentially insert a bamboo skewer on the little ridge beneath the screws (see photo) which removes almost all the tension from the levers on the case.

You can then safely unscrew/screw the mechanism without risking the screw threads and hence (if you want) fit the springs *before* re-attaching the mechanism (much easier as way more space and angles)

Again I’m not an experienced fettler, so there may be some downside to this I’m not aware of, or some magic tool which makes bending springs back in situ less hard, but I thought this was a nifty tip, so sharing incase of use to anyone.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Possible nifty tip when fitting hohner springs after refacing pallets
« Reply #1 on: December 28, 2025, 07:02:14 PM »

I find it quite simple to use a small bladed screwdriver with a hacksaw cut, or a Dremel made notch, across the middle of the end of the blade.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Possible nifty tip when fitting hohner springs after refacing pallets
« Reply #2 on: December 28, 2025, 07:15:01 PM »

As for nifty tools I use a jewellers screwdriver in to which I've cut a slot in the blade. Useful to both release and refit springs



Winston beat me to it

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Possible nifty tip when fitting hohner springs after refacing pallets
« Reply #3 on: December 28, 2025, 07:31:07 PM »

But you were probably doing it well before me!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Sebastian Trudgian

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 124
  • DG Pokerworks and also play Irish Whistle/Flute
Re: Possible nifty tip when fitting hohner springs after refacing pallets
« Reply #4 on: December 28, 2025, 07:52:40 PM »

Ok… hold the phones… that is a true nifty tip!

A screwdriver with a spring sized gap in it would make it an awful lot easier, great idea! (I’ve been using a regular sized screwdriver + my finger and a loop made out of a paper clip)

Will try making one 🥰
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Possible nifty tip when fitting hohner springs after refacing pallets
« Reply #5 on: December 29, 2025, 08:13:09 AM »

I have a small flat screwdriver with a v shaped slot on one side of the end of the blade and a sort of hook slot in the side of the blade…all made with a needle file. An essential tool for manipulating springs..but also very useful for working on the innards of a PA bass machine. The shaft of the screw driver is 5 or 6 inches..to give it 'reach'.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Possible nifty tip when fitting hohner springs after refacing pallets
« Reply #6 on: December 29, 2025, 08:32:06 AM »

I just pick up any spare rod that I have handy and cut a notch.

Then forget where I've put it, so I make a new one.

I must have about 20 of these spring tools hidden around the house  :-[
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal