Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Retuning a Honer Club bass side from C/F to D/G  (Read 570 times)

0 Members and 1 Guest are viewing this topic.

Peter Furness

  • New Starter
  • Offline Offline
  • Posts: 3
Retuning a Honer Club bass side from C/F to D/G
« on: August 18, 2026, 02:52:36 PM »

I'm retuning a Honher Club modell VIII from C/F to D/G.  Retuning the treble side has gone reasonably smoothly.  I'm a beginner when playing it, but my local melodeon experts tell me the sound is good.  (Although I'm leaving the accidentals till later...).

But I've hit a problem with the bass side.

It has eight buttons (four bass and four chord), and I believe the chord and bass buttons in D/G need to be C/C, G/D, B/E and D/A. 

Chords have three notes, so for four chord pairs that's 12 pairs of reeds.

But the box only has the mechanics for ten reed pairs!

Hohner seemed to get round this in the original C/F tuning by using some of the reed pairs for more than one chord.  I don't see how to do that in D/G.  I'm told it can be done;  but how?

More information about what I've done so far, following what I found when tuned to C/F,  in case there's an answer there...

The bass notes all play FOUR octaves, for example C plays C2, C3, C4 and C5. A broad range, but I believe that's as it should be.
The reeds for C4 and C5 are on opposite sides of the wooden reed-holder but are activated by a single pad.  The same pad also opens when playing the C chord.
In fact all the chord buttons play their three notes at two octaves.  So the C chord plays C4 and C5, E4 and E5, G4 and G5.  But that's done using one pad for each octave pair, so I see no scope for freeing anything up there.

I can see that chords C and D are replicated by different buttons, so I thought there might be an answer there.  But the push and pull reeds for a single button have to be on each side of the same reed plate. So, if I was trying to avoid duplication of the D chord, the pairs on one plate can't be both (D and A) and (G and D) at the same time.

Help!  I'm thinking maybe I will have to sacrifice one of the less used chord buttons - maybe B+E-.  But I'd rather not.

Many thanks in anticipation...

Peter
 (:)
Logged

Andy Goldfinch

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 150
    • Andy Goldfinch Melodeon (YouTube)
Re: Retuning a Honer Club bass side from C/F to D/G
« Reply #1 on: August 18, 2026, 03:43:15 PM »

Could it be going from Club to standard basses that would be the issue here, rather than going from C/F to D/G?

I've just written out a chart of the notes in each of the standard D/G 8 bass chords, and have got both the G/D and D/A chords needing a D/A reed plate, so that could be shared.

The only other sharing pair I can see would be keeping the C bass clubbed (F/C instead of the standard C/C), in which case you could share the A/E reed plate between your F/C and D/A chords.

Alternatively the way to work out what reed sharing was originally intended would be to take the reed block out and then see which pallets get opened by more than one chord button, and then look at which reeds are in that position on the block.
Logged
D/G Castagnari Dony, D/G Hohner Club VII (9 bass), D/G Serenellini Maestro, C/F Hohner Club II (DIY restoration in progress...)

https://www.youtube.com/@andymelodeon

Peter Furness

  • New Starter
  • Offline Offline
  • Posts: 3
Re: Retuning a Honer Club bass side from C/F to D/G
« Reply #2 on: August 18, 2026, 04:22:02 PM »

That's a brilliant reply, thank you.  But as a novice melodeon player I'm wondering why Hohner's Club melodeons had F/C bass and chord buttons rather than the standard C/C, and what the effect will be on playability?  It does look as though it would complicate my efforts to learn to play!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Retuning a Honer Club bass side from C/F to D/G
« Reply #3 on: August 18, 2026, 05:14:19 PM »

Agree with Andy.  It’s the club bass that is the issue.  You have two options - FC instead of CC,  or you may be able to leave out some of the shared reeds so that one chord is incomplete.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Retuning a Honer Club bass side from C/F to D/G
« Reply #4 on: August 19, 2026, 08:01:49 AM »

As a sort of extra bit of info…you are going from a club bass to standard bass..if memory serves..CF has a BbEb pair where you would put a CC pair on a DG. So if you push the BbEb up a tone you would get a CF pair..but you want a unisoric CC pair. In a declub situation I often find some old Hohner PA reeds for a unisoric pair, including the chord. ..so C, plus C, E, G. It tends to be a better solution than lots of repitching.
I've always been able to work our a solution re declubbing, without blocking off reeds or only having a partial chord.
I would be curious to see a photo of the bass mech on your box though. In general the chords are hard coded and the only problem one sometimes gets is that the push pull pairs are spread over three reeds and the tonic, third and fifth may not be on the same plate. If it has a stradella mech then that is a different matter…
« Last Edit: August 19, 2026, 08:12:06 AM by Rog »
Logged

Andy Goldfinch

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 150
    • Andy Goldfinch Melodeon (YouTube)
Re: Retuning a Honer Club bass side from C/F to D/G
« Reply #5 on: August 19, 2026, 08:09:02 AM »

I've found another reed sharing opportunity, the D/A & B/Em chords could share an F#/E reed plate. It will depend on what your mechanism is doing though, if it's a mini stradella mechanism like my Club VII then changing which chords share reeds would be a challenge, so sticking to whatever sharing the stradella is already set up for would be best. My Club VII has no thirds in the chords (at my request), so doesn't hit this problem.
Logged
D/G Castagnari Dony, D/G Hohner Club VII (9 bass), D/G Serenellini Maestro, C/F Hohner Club II (DIY restoration in progress...)

https://www.youtube.com/@andymelodeon

Blenchy

  • Blenchy
  • Good talker
  • **
  • Offline Offline
  • Posts: 74
  • What do you mean it's upside down?
Re: Retuning a Honer Club bass side from C/F to D/G
« Reply #6 on: August 24, 2026, 09:44:41 AM »

I had a similar issue with a Club IIIM. It was kept in it's CF tuning but I de-clubbed it as a lot of the chord reeds had been damaged and lost over time so figured I had a clean slate. That's where I also encountered the shared reeds!!

I knew I wanted to tape thirds and have the Eb/Bb bass as a Bb/Bb (Equivalent of your C/C on a DG) instead. In the end I found the easiest way to get around this was to just remove some reed plates all together and juggled around the reed plates. It's not too noticeable when playing as it's the third of the chord I wanted out that got removed and it seemed the easiest solution at the time.

I might revisit it but it was definitely the easiest solution at the time. If it'd help I can take some pictures tonight and write out what each of the reed plates are and translate it into DG terms for you?

Hope that all makes sense!
Logged
David Blench - Sheffield

Hohner Pokerwork and Laurel D/G, 3 Voice Galotta D/G, Old 12 bass Hohner Bb/Eb, 4 Voice "Foreign" C one row. Some concertinas and many more boxes in bits

Part of Handsworth Sword and Rumworth Morris
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal