Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Hardware for a melodeon case  (Read 6511 times)

0 Members and 1 Guest are viewing this topic.

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Hardware for a melodeon case
« on: June 14, 2010, 04:17:45 PM »

Hi,

I probably need to make at least one melodeon case.   Can anyone point me to a supplier for latches, handles etc to make a nice job?   Last time I did anything similar you could just walk into any number of hardware shops, but of course that's not the case now.   I've looked at a couple of mail order places (Isaac Lord and Rutlands) and they have some stuff for cases but its clearly not their focus compared to furniture and joinery hardware.  

Thanks,  Tony S
Logged
Tony S

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hardware for a melodeon case
« Reply #1 on: June 14, 2010, 04:33:48 PM »

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Hardware for a melodeon case
« Reply #2 on: June 14, 2010, 04:42:55 PM »

Cheers.

Now I'm confused, I meant to post this into "Construction and Repair",  but a moment ago it looked like I'd put it in "Instrument Makes and Models" .... which probably warrants a rebuke from above.
Logged
Tony S

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hardware for a melodeon case
« Reply #3 on: June 14, 2010, 04:45:24 PM »

I've tried making an appearance from out of swirling clouds, with thunder rolling in the distance, but I can't quite get the hang of it, so I just quietly moved your topic that was clearly in the wrong place.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Hardware for a melodeon case
« Reply #4 on: June 14, 2010, 06:04:19 PM »

http://www.penn-elcom.com/Default.asp?GC=Home

They don't really do retail, but if you talk nicely they might sort something out.
Logged

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Hardware for a melodeon case
« Reply #5 on: June 14, 2010, 06:37:29 PM »

Maplin do a range of case hardware

http://www.maplin.co.uk/Family.aspx?Menu=1626&worldid=-5
Thanks for the link, Lester. I've been looking for a source of such things for a while. And to think I was in Maplin's just this morning! (for something else).
Logged

Ga

  • Good talker
  • **
  • Offline Offline
  • Posts: 62
Re: Hardware for a melodeon case
« Reply #6 on: June 15, 2010, 10:08:50 AM »

For all your flightcase needs, Swanflight - go to the "flightcase hardware" section for corners, latches, hinges, etc.   Possibly any type of hardware you will ever need, for everything from a small case for a concertina, to a flight case for a full 19" rack.  They're not especially geared up for small retail, but they do supply small orders (I once ordered a single hinge - dealt with no problem), the website takes orders.   Not the quickest, but certainly full delivery within 3 to 4 days.  I recommend them - All my guitar amps, PA, microphones, speakers, stands and monitors travel in flight cases cabinets made with Swan hardware.  A lot of the hardware is actually made by Penn, as mentioned previously by Graham W, but Swan is the retailer:
http://www.swanflight.com/acatalog/Case_Hardware.html    

Also, Isaac Lord.  More geared up for small retail, but not as large stock of specialist fittings. I've also used them with happy results.
http://www.isaaclord.co.uk/categoryOverview.aspx?subCat=1&parentCat=1

Also, Maplin, as previously mentioned.

Logged

plasteraccordion

  • New Starter
  • Offline Offline
  • Posts: 2
Re: Hardware for a melodeon case
« Reply #7 on: June 16, 2010, 03:33:44 AM »

Check out Rockler- on the web- there's another site, but I can't remember at the moment- best, Steve
Logged

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Hardware for a melodeon case
« Reply #8 on: June 16, 2010, 08:28:12 AM »

Thanks.  There's some stuff there.   In passing, why do people make reasonably nice looking reproduction hardware, then show it fitted with cross-point screws?
Logged
Tony S

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Hardware for a melodeon case
« Reply #9 on: June 16, 2010, 03:44:44 PM »

I guess it's just for convenience!
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Hardware for a melodeon case
« Reply #10 on: June 16, 2010, 03:47:35 PM »

Gandy

A "major"   aggravation to me as well.

I make vernacular furniture from a period of 1800-1950

The use of any Reed and Prince or Phillips screws just lets you know  the user/supplier is clueless
as the supposed date of patent was around 1937.

Aside from that, any fool can use a Phillips screw driver, but a slot head screw takes someone with a
steady hand and a desire to do it right to drive it without damage.

I abhor cross type screws and am known to replace them on about anything..
accordeons, guitars, furniture  etc.

Just one of those little "button pushers" of life.

Rockler..  not my favorite, though the old man was ok before he turned the company over to his yuppie children with their
new age marketing and no understanding of wood working.  Just my opinion.

I use Crown or Restoration Supply or  a number of other sources for hardware including case hardware.
« Last Edit: June 16, 2010, 03:49:27 PM by melodeon »
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hardware for a melodeon case
« Reply #11 on: June 16, 2010, 04:24:42 PM »


Just one of those little "button pushers" of life.


Do you have to line up the slots on adjacent screws, and make sure door hinge screws are aligned with the slot in a vertical alignment to ensure any liquid drains?

No? Oh! it's just me then   ::)

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Hardware for a melodeon case
« Reply #12 on: June 16, 2010, 04:48:57 PM »


[/quote]

Do you have to line up the slots on adjacent screws, and make sure door hinge screws are aligned with the slot in a vertical alignment to ensure any liquid drains?

No? Oh! it's just me then   ::)
[/quote]

No Lester and Al, you are not alone, hatred of x points on anything which ought to look right is alive and well here in Norfolk too (but will whizz them in with the cordless drill if speed and ease of assembly is important)

As for having the slots right, yes I do too, it shows someone has done the job who cares about it - restoring some of our stationary steam engines where countersunk slot heads were used this means either doing a really long try and see exercise or sometimes we cheat and 'tickle' the countersink a bit to get the same result - imagine an engineering firm these days paying fitters to fit the same screw several times to get the alignment right - no wonder we are faced with x points everywhere.

As an aside for those who engage in 'agricultural' wood and metalwork, one of my favourite tools for those stuck screws etc. often encountered is a ratchet hand brace drill with the 'blacksmith' chuck replaced by a keyless 3 jaw from a dead cordless drill - maximum torque and with my full weight applied, slot or crossheads either release or expire  >:E I also use it for drilling large holes and to drive threadcutting taps.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hardware for a melodeon case
« Reply #13 on: June 16, 2010, 05:23:43 PM »

I agree with the previous points about screw heads.  Its a particular problem when working on nice old concertinas which use several very small sizes of screw which are very difficult to buy today.  Any suggestions for suppliers?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Malcolm Austen

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 495
  • any old hohner
Re: Hardware for a melodeon case
« Reply #14 on: June 16, 2010, 05:46:03 PM »

Vertically aligned screw heads can be observed on quality narrow boats. I heard that you use a steel screw, welded to the end of a rod, to screw in first and then put the brass screw in to minimise the chances of head damage.
One thought though if all the slots are vertical then are 99% of them at an incorrect tightness?
Logged
aka malodeon

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hardware for a melodeon case
« Reply #15 on: June 16, 2010, 05:52:32 PM »

I heard that you use a steel screw, welded to the end of a rod, to screw in first and then put the brass screw in to minimise the chances of head damage.

One of the more useful things I learned from Emmanuel Pariselle when biuld my melodeon was the use of wax on screws to ease their passage into the wood. Really makes a difference.

Quote
One thought though if all the slots are vertical then are 99% of them at an incorrect tightness?

I agree that this is a problem but not a 99% problem

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hardware for a melodeon case
« Reply #16 on: June 16, 2010, 07:13:27 PM »

Vertically aligned screw heads can be observed on quality narrow boats. I heard that you use a steel screw, welded to the end of a rod, to screw in first and then put the brass screw in to minimise the chances of head damage.
One thought though if all the slots are vertical then are 99% of them at an incorrect tightness?
The other problem with brass screws is that they can shear off along the shank if a pilot hole has not been properly drilled and they get too tight whilst being driven in. Removal of the sheared off portion is almost impossible and is likely to mess up the job permanently.

When fixing hardwood or the denser softwoods with brass screws, first drill a pilot hole about 3/4 the final depth of the screw, then a shallower, wider, clearance hole for the screw shank. Countersink if needed. Then drive a steel screw (the same size as the final brass screw) nearly all the way home, apart from perhaps half a turn.

Remove the steel screw and replace with the brass screw, with the thread waxed first by rubbing along a bit of candle stump. The brass screw should go in snugly and have enough leeway in the final turn to allow the slot to be aligned in its desired orientation.
« Last Edit: June 16, 2010, 07:16:22 PM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Hardware for a melodeon case
« Reply #17 on: June 16, 2010, 08:50:40 PM »

I agree with the previous points about screw heads.  Its a particular problem when working on nice old concertinas which use several very small sizes of screw which are very difficult to buy today.  Any suggestions for suppliers?

Only one size - 1/4" brass but it's a start.

Edited to add: a slightly smaller screw only 5mm long.

Have you tried David Leese Theo?
« Last Edit: June 16, 2010, 08:58:44 PM by tallship »
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Hardware for a melodeon case
« Reply #18 on: June 16, 2010, 10:41:12 PM »

I agree with the previous points about screw heads.  Its a particular problem when working on nice old concertinas which use several very small sizes of screw which are very difficult to buy today.  Any suggestions for suppliers?
I haven't dealt with these people yet, but they list some very small screws, both nickel-plated and brass.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hardware for a melodeon case
« Reply #19 on: June 16, 2010, 10:47:05 PM »

I've used them before, they seem to have extended their range since I last ordered from them.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal