Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Tuning reeds. Easy or hard?  (Read 6886 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning reeds. Easy or hard?
« Reply #20 on: August 12, 2010, 10:46:11 PM »

You can also wreck a small reed with an inexpertly used file.  I learned that the hard way! 

A sandpaper file made from medium or fine abrasive paper glued to a small stick is a cheap and gentle way of removing metal from reeds.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Tuning reeds. Easy or hard?
« Reply #21 on: August 12, 2010, 11:22:49 PM »

I get the impression that the use of Dremel type tools is frowned upon more for aesthetic reasons than anything else.

There's certainly that but along with the potential for small mistakes quickly ruining a reed some also argue that the way using them at the base to lower the pitch changes the profile at the side is detrimental and removing metal in one fairly concentrated place rather than taking longer strokes with a scratcher potentially shortens the life of the reed and makes it more likely to break. That's the theory anyway but whether or not it actually works like that in practice is a whole different debate that's beyond the scope of this thread.

I have the posh digital Dremel with a zillion bits and accessories and when I bought it I thought it was going to be so useful but I only use it with one bit and one attachment, both specialised and bought elsewhere, for cutting out soundholes and making the channels for soundhole rings. You can use them to do a lot of things but it's rarely the best tool for the job.
Logged

HallelujahAl

  • Guest
Re: Tuning reeds. Easy or hard?
« Reply #22 on: August 13, 2010, 06:53:35 AM »

Quote
You can use them to do a lot of things but it's rarely the best tool for the job.
I couldn't agree more! I too bought the lot and yet have only found very limited use for it - and no power tool ever goes anywhere near any of the concertinas I restore.
AL
Logged

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Tuning reeds. Easy or hard?
« Reply #23 on: August 19, 2010, 11:53:53 PM »

I've been reading this thread with some interest. My own personal feeling, whether it be right or wrong is: Metal is being removed from the reed tongue to reduce mass either at the tip to raise the pitch, or at the base to lower it. However, providing this is carried out with care and an understanding of the tools and materials used either files or powered tools are ok to use. (I think an angle grinder might be pushing it) :o
Personally I will use a file for tuning as much as I can but there is a point where it is far safer to use a very fine engraving tool, particularly on the smaller reeds (I find the amount of pressure needed to 'scratch' them pushes them out of set anyway)
Look at the reeds of a lot of boxes new or old and they will have been tuned by some sort of mechanical means.

Martyn
« Last Edit: August 20, 2010, 11:25:28 AM by martyn »
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal