Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Hohner "Steel Reeds" rehab  (Read 9106 times)

0 Members and 1 Guest are viewing this topic.

jeverist

  • Member
  • *
  • Offline Offline
  • Posts: 22
Hohner "Steel Reeds" rehab
« on: November 08, 2010, 03:43:11 PM »

Hi, all.  New member here with a few questions.  I have a single-row Hohner (in D) that I got off ebay several years ago.  Having found Charlie Marshall's "paint them on" reed waxing video, I've decided to give it a shot.  The reeds plates are currently being held in by tacks and small nails.  Am I correct in assuming that this was done in lieu of a proper rewaxing, and that these should not be used?  The tuning seems to still be pretty good and I think that it will be OK after the rewax.  The reeds and plates themselves are clean and not rusty.  However, if I want it re-tuned later, will the reeds need to be removed again, or are they retuned in place?  The reed blocks are glued to the air-hole pieces and are not removable.  Thanks very much for any help here.

John
Logged
4v C#/D Paolo Soprani, derelict G & D single-row Hohners, Dipper C/G 32b Anglo, Acadian C

HallelujahAl

  • Guest
Re: Hohner "Steel Reeds" rehab
« Reply #1 on: November 08, 2010, 05:09:27 PM »

It's even possible that the reeds were not meant to be waxed in on your instrument. Any chance of putting a photo or two up?
AL
Logged

jeverist

  • Member
  • *
  • Offline Offline
  • Posts: 22
Re: Hohner "Steel Reeds" rehab
« Reply #2 on: November 08, 2010, 06:45:35 PM »

Hi, Al

thanks for the response.  I'll try to attach some pics of the reeds to this post.  lots of wax in there with the tacks and nails over that.  There also looks like there is some re-gluing of the block pieces on the bass side that has overlapped the reed plates (even in the inside of the cavity).  The low note block must've come undone at some point and it was just re-glued with the reeds attached.  I do have the missing reeds and plate.  Most of the reed plates look to be zinc stamped with "H", but there are two in the bass chord blocks that appear to be aluminum, also stamped "H"


Logged
4v C#/D Paolo Soprani, derelict G & D single-row Hohners, Dipper C/G 32b Anglo, Acadian C

jeverist

  • Member
  • *
  • Offline Offline
  • Posts: 22
Re: Hohner "Steel Reeds" rehab
« Reply #3 on: November 08, 2010, 06:46:28 PM »

looks like they didn't attach....will keep trying.  sorry      J
Logged
4v C#/D Paolo Soprani, derelict G & D single-row Hohners, Dipper C/G 32b Anglo, Acadian C

jeverist

  • Member
  • *
  • Offline Offline
  • Posts: 22
Re: Hohner "Steel Reeds" rehab
« Reply #4 on: November 08, 2010, 07:12:16 PM »

how's this?
Logged
4v C#/D Paolo Soprani, derelict G & D single-row Hohners, Dipper C/G 32b Anglo, Acadian C

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner "Steel Reeds" rehab
« Reply #5 on: November 08, 2010, 07:18:19 PM »

That is quite a rare box - a forerunner to the Hohner 1040, single row, two voice.
The nails and tacks are original and were applied after waxing as a sort of belt and braces approach.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

HallelujahAl

  • Guest
Re: Hohner "Steel Reeds" rehab
« Reply #6 on: November 08, 2010, 07:36:54 PM »

I would imagine that if needing to retune at a later date it would be that the reeds would need to be removed?
AL
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner "Steel Reeds" rehab
« Reply #7 on: November 08, 2010, 07:41:24 PM »

 Having found Charlie Marshall's "paint them on" reed waxing video, I've decided to give it a shot.

When you have the reeds off to clean off the old wax please also replace all the leather flap valves.  The picture shows the valves are curled up, they should lie flat.  They will be causing at least as many horrible noises as the old wax.

No the reeds would not have to be removed to be tuned, unless you were changing the overall pitch, for example from the old German standard of A=435 to modern concert pitch A=440Hz.  Whatever the process the final tuning must be done in situ.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

HallelujahAl

  • Guest
Re: Hohner "Steel Reeds" rehab
« Reply #8 on: November 08, 2010, 07:48:45 PM »

Quote
Whatever the process the final tuning must be done in situ.
Given that the reedblock can't be removed would it be a case of using its own bellows as tuning table then?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner "Steel Reeds" rehab
« Reply #9 on: November 08, 2010, 07:49:31 PM »

Exactly.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

jeverist

  • Member
  • *
  • Offline Offline
  • Posts: 22
Re: Hohner "Steel Reeds" rehab
« Reply #10 on: November 08, 2010, 09:07:47 PM »

thanks, guys

I'll put valve replacement on the to-do list, and will also re-nail and tack.  Even with all the horrible groans, wheezes, and rumbles this is quite a sweet sounding box
Logged
4v C#/D Paolo Soprani, derelict G & D single-row Hohners, Dipper C/G 32b Anglo, Acadian C

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Hohner "Steel Reeds" rehab
« Reply #11 on: November 08, 2010, 09:40:52 PM »




  Even with all the horrible groans, wheezes, and rumbles this is quite a sweet sounding box
Sounds just like some eBay descriptions ;D
Logged

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Hohner "Steel Reeds" rehab
« Reply #12 on: November 08, 2010, 11:08:39 PM »

When I did mine, I found just the wax a satisfactory hold and left the nails off.  :||:
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner "Steel Reeds" rehab
« Reply #13 on: November 09, 2010, 12:28:53 AM »

 Having found Charlie Marshall's "paint them on" reed waxing video, I've decided to give it a shot.

When you have the reeds off to clean off the old wax please also replace all the leather flap valves.  The picture shows the valves are curled up, they should lie flat.  They will be causing at least as many horrible noises as the old wax.
Essential advice from Theo, of course.
All I will add is that the four highest (smallest) reed plates which do not have valves in your photo should be left as such; don't be tempted to add valves to these, as they are not required.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Hohner "Steel Reeds" rehab
« Reply #14 on: November 09, 2010, 07:53:28 AM »

I'll put valve replacement on the to-do list, and will also re-nail and tack. 

There is no reason to re-tack the reeds once you have waxed them in. The wax its self provides plenty of support to stop them moving, and putting nails back in is a pain.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner "Steel Reeds" rehab
« Reply #15 on: November 09, 2010, 07:59:30 AM »

The nails are quite unnecessary.  Hohner do not use nails on the boxes they make now.
As far as I can tell the only thing that the nails do is to hold the reeds in place when the wax has perished after several decades.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Hohner "Steel Reeds" rehab
« Reply #16 on: November 09, 2010, 12:12:38 PM »

I see a lot more H1140 models with failed wax than any other Hohner model.

Probably because of the flat mounting of the reeds rather than A frame blocks which other Hohner models have.

Seems to be the case with both early and late model H1140s.

So I will have to go against the flow here and recommend that you use the nails in this particular case.

My 10c....
Logged
Tuner/repairer, now retired.

jeverist

  • Member
  • *
  • Offline Offline
  • Posts: 22
Re: Hohner "Steel Reeds" rehab
« Reply #17 on: November 09, 2010, 01:31:23 PM »

thanks again, for all this good advice.  I can see how putting the nails back in on the perpendicular bass reed plates would be problematic.  Probably have to support the block some how when nailing.  Any chance that these bass plates were waxed on to the blocks prior to gluing in the blocks originally?  would be easier and explain the glue excess found inside the reed cavity (can be seen in the photo - missing reed plate).  Anyway.... I'll decide about the nails when I get to that point.

hope in the end to be able to enjoy the way these reeds sound without being distracted by the "noise".  Thanks for insisting on new leathers
Logged
4v C#/D Paolo Soprani, derelict G & D single-row Hohners, Dipper C/G 32b Anglo, Acadian C

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Hohner "Steel Reeds" rehab
« Reply #18 on: November 09, 2010, 04:22:08 PM »

I bought the same exact box although in "C" just a few months ago.  It's in even better condition but the reeds need full overhaul also, it's my winter project. I will be watching this thread with interest.
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Hohner "Steel Reeds" rehab
« Reply #19 on: November 10, 2010, 01:18:40 AM »

My earlier post and comments about loose reedplates referred more to the treble end than the bass end.

Just a further point regarding the "nails".

A bit of a misnoma perhaps; they are more like mushroom headed thumb tacks.

Jeverist, I would not recommend hammering them in as you would with a nail, but instead just press them in with your thumb, perhaps using an old flat file or similar for a little extra pressure. The wood into which they need to be pressed is fairly soft and the pins are quite sharp. (Ouch!)

Incidentally, I have a 2 row version of your Hohner with the same faux birds-eye maple veneer, though slightly different transfers.
« Last Edit: November 10, 2010, 01:23:38 AM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal