Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3 4   Go Down

Author Topic: Going to make a box - what should I know?  (Read 16024 times)

0 Members and 1 Guest are viewing this topic.

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Going to make a box - what should I know?
« on: June 08, 2011, 11:23:20 PM »

i AM going to make a box - a two-row small 3 voice!  I've been saying it for years and years and unless I say I will ... err... I won't!

I have almost no woodworking skills at all, I was a disaster with all woodworking at school although I am now a lot more patient and attentive to detail than I was.  I am, however fairly competent with repair work of the mechanics and reeds on my own instruments.

So ... I know some here have made instruments from scratch either off their own backs or through the building courses run by Emmanuelle Pariselle, and I know there are some pro makers who visit here Rees, Stormy etc..... 

What should I know?  Not instructions from start to finish ... but just advice on the approach to take, the set up needed, tips and tricks or pearls of wisdom would be very gratefully received.

Cheers

Squeezy

PS - I fully intend to ruin large amounts of wood, swear a lot, give up a couple of times and spend lots of money on equipment it turns out I don't need on this project.

Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Going to make a box - what should I know?
« Reply #1 on: June 08, 2011, 11:26:25 PM »

I'd suggest taking it in stages.    Start with reedblocks, and make a new set of blocks for an existing instrument, perhaps in a different key.  I reckon the reedblock is about the most complicated wooden part, if you can manage that the rest should be relatively easy.  

You will need to do a lot of precision sawing of small bits of wood.  I can recommend one of these Proxxon model makers saw benches:
http://www.axminster.co.uk/proxxon-proxxon-fks-e-table-saw-prod20020/
http://www.axminster.co.uk/proxxon-proxxon-fet-table-saw-prod791265/
« Last Edit: June 08, 2011, 11:35:45 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #2 on: June 08, 2011, 11:33:11 PM »

Thanks Theo - that's a very good idea, I hadn't even though about that.  Are there any variables that you know of that change the sound properties of reedblocks that I could experiment with?

Keep 'em coming!
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Going to make a box - what should I know?
« Reply #3 on: June 08, 2011, 11:38:11 PM »

That's good advice. Building an instrument from scratch without plans would be tricky. I've been "studying" Engineering for what seems like a lifetime and I still have a very sketchy understanding of how you would go about designing a box. I think though that reedblocks are probably the most critical aspect, because they not only dictate the sound to some extent, they also impose constraints on the size. There would be no point in building a cabinet and then finding that your reeds don't fit!

I would really like to do this project (although I want a small three row three voice, BCC#) and I will one day. I would go about it by first deciding on the orientation of my reeds (currently thinking about M flat mounted, M+ in a inclined pan, L on a conventional block in the middle. Three rows into two rows of pallets as the Shand Morino) and then prototyping reedblocks into an instrument of a known sound and response of a similar sort of size. If you mock up a few reedblocks, attach a few reeds, say one for each octave, splice into a pokerwork, record and see how they respond then you would be able to more easily change your mind about how it should be set up. Once you think that you have a good orientation and chamber size then think about the fondo, how big it should be (because lots of spare space on the fondo has a different sound to very little) and what material (aluminium, ply or solid wood?). Then do the same with the bass end. At the end of that you should have your size constraints and so you can define your bellows dimensions.

Then comes the mechanisms and I haven't got that far in my thinking :P I'm presuming that you don't have a waterjet cutter and I don't know how best to manufacture the mechanism otherwise, other than buying stock, which might not fit.

My feeling is that you should start on the inside and work your way out, making the bellows last. Does that make sense to others? I obviously have no experience in this sort of thing.

You might find www.mimf.com of interest for woodworking stuff. I presume that you know about the boxbuilders yahoo group already.

EDIT: If someone has a conclusive idea of exactly what (quantifiable) effect reedblock chamber size has on the reeds then I would be very interested to hear from you...
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Going to make a box - what should I know?
« Reply #4 on: June 08, 2011, 11:40:58 PM »

Yes, two main ones I can think of, type of timber used being the obvious one.  The way the block is constructed is the other: 1) Built up from smaller pieces glued together, most Hohner and most Italian makes are like this, or 2) Reed chambers carved out of a solid block with separate cap and base, common on Paolo Sopranis and a few other Italian makes.  
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #5 on: June 08, 2011, 11:51:08 PM »

Cheers Theo,  so - similar to Ukebert's question here, what qualities of the timber / construction affect which parts of the sound?  I know with soundboards I'm looking for a very stiff material if I want to transmit the maximum volume and higher frequencies to the listener.  Is it the same with reed blocks?
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Going to make a box - what should I know?
« Reply #6 on: June 08, 2011, 11:57:06 PM »

I really have no clear answers to that.  But some hunches:  The less sound absorbed in the blocks the better, so rigidity, density, mass, and timbers with good acoustic properties (spruce, maple, cedar etc) are probably good.  I'm sure there are numerous details of construction that are all influential on the final sound.

Sound boards (are not soundboards but we all know what you mean)  the only observation I would add is that Frans van der Aa uses rather thin and flexible high quality ply and his boxes sound great.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #7 on: June 09, 2011, 12:09:13 AM »

Thanks Theo,  I shan't bother you any more tonight!  It's pretty much what I thought and it will be (as Ukebert suggested) a process of experimentation which is great.  What you have said does verify what I have seen in boxes I have owned/looked inside.

By the way - I plan on a waxless design.  I hate wax and reed-waxing, it's so messy and can be a major source of debris that gets in the reeds eventually.  So my reeds will be screwed/pinned in to a bed of suede or something with similar properties.  Plus the boxes I have owned with this design have all sounded very direct which is the kind of sound I am going for.

Good night,

Squeezy.

PS - anyone else?
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Going to make a box - what should I know?
« Reply #8 on: June 09, 2011, 12:13:56 AM »

I have read so many conflicting accounts of the influence of the fondo on the acoustics of the box that I am currently in the confused stage :P I intend to bend my project supervisor's ear about it next year (he's an expert on violin acoustics, I'm hoping that he can give some insight, even though free reeds are different in every conceivable way).

I think that wax has a larger effect on sound than I had bargained for. Certainly from my own limited experience of rewaxing boxes the amount of wax used can have quite an effect on the sound and to preserve the tuning if you need to change the valve, putting on a similar amount of wax than you took off seems to work well. I think that the less wax used the more direct the sound, so it would make sense that pinning would exemplify that. It would be more difficult to get right though, wax is very forgiving. The reedblocks would also probably be bigger and bulkier, which could be critical in a small box.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Going to make a box - what should I know?
« Reply #9 on: June 09, 2011, 08:09:38 AM »

Cheers Theo,  so - similar to Ukebert's question here, what qualities of the timber / construction affect which parts of the sound?  I know with soundboards I'm looking for a very stiff material if I want to transmit the maximum volume and higher frequencies to the listener.  Is it the same with reed blocks?

Try this

http://forum.melodeon.net/index.php/topic,7117.0.html

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Going to make a box - what should I know?
« Reply #10 on: June 09, 2011, 08:17:57 AM »

The reedblocks would also probably be bigger and bulkier, which could be critical in a small box.

Not necessarily.  Shand Morinos use screwed i plates, and have almost not space between plates.  Instead of having space for screws between plates they either placed at the ends, or the edges are notched to make room for the screw.

By the way - I plan on a waxless design.  I hate wax and reed-waxing, it's so messy and can be a major source of debris that gets in the reeds eventually.  So my reeds will be screwed/pinned in to a bed of suede or something with similar properties. 

If using screws you will need to be careful about the type of timber used for the edges of the reed chambers, softer woods like spruce may not give enough grip for the screws.  Emanuel P uses maple.  He also uses a self adhesive gasket material called "olovice adesivio"  I have some of this if you want to try it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Going to make a box - what should I know?
« Reply #11 on: June 09, 2011, 10:24:48 AM »

I had a super serious research into building some boxes a year or so ago (had to put it on hold as a table saw in a one bedroom flat isn't really feasible, especially with a neat a tidy missus) and whilst I could conceptualise the wood work in my head, the bass and treble mechanisms from scratch look like a right royal pain the back side.

A basic wooden stepped keyboard like a Max or a Tommy is just precision wood work - I would get a table mountable router or milling machine to do it quickly and accurately. But with a metal setup I wouldn't really consider making one as the assemblies are available from Carini's. It would save lots of time and energy which would be better placed into reed work and beautifying (and stops sharp metal piercing finger tips).

The reason I say this is that if you buy any pre-made parts then you have to tailor the whole box to their sizes. Obviously with building your own wooden mechanism this isn't an issue.

Also, I assume bellows are coming from Galassi - I don't see the point in sticking my own when they can do an amazingly better job for a really reasonable price, in any size/shape/colour etc.

Russells.com is the place to go for any leather - send them samples and they will match it. Waxless design is the way forward, so much less mess, and way easier to maintain, it's just offset by initial fiddlyness.

There are lots of builders websites with photo tours etc - these are amazingly useful for getting your head round certain processes... apart from the Bergflot site, where every time you wonder how on earth he makes a certain amazingly intricate part, you just see it on the plasma cutter... grr.. jealous!
Logged

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #12 on: June 09, 2011, 11:26:36 AM »

Some great advice there too.  BTW - Lester's link is to the recent thread by Peter (Stormy) Hyde about his boxes made from foam where he talks about the fact that his boxes have foam reed blocks.

So to recap:

1: Make the smaller components first as these are a) a bit fiddly and b) can affect the final dimensions and qualities of the box.  Reed blocks and treble/bass mechanisms are suggested.  I'm assuming if coupler mechanisms are to be made they need to be taken into consideration as well.

2: If buying in from outside (Carini), make sure you know the dimensions!

3: Get your bellows from Galassi unless you reeeeeeallllly want to know how to do it.

4. Get a table saw. (expensive - but probably very useful)

That's a great start.  Are there any other pearls of wisdom out there?
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Going to make a box - what should I know?
« Reply #13 on: June 09, 2011, 11:32:10 AM »



That's a great start.  Are there any other pearls of wisdom out there?

Don't worry about mistakes, just learn from them.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Going to make a box - what should I know?
« Reply #14 on: June 09, 2011, 12:32:11 PM »

By the way - I plan on a waxless design.  I hate wax and reed-waxing, it's so messy and can be a major source of debris that gets in the reeds eventually.  So my reeds will be screwed/pinned in to a bed of suede or something with similar properties.  Plus the boxes I have owned with this design have all sounded very direct which is the kind of sound I am going for.

I 100% with you on this! It's also part of my plans in a similar project.

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #15 on: June 09, 2011, 01:05:47 PM »

If I'm thinking about reed blocks - I suppose I have to think about reeds.  Eventually I will be thinking about high end reeds for the box, but obviously different reed makes have slightly different dimensions, don't they, so should I start off by buying the reeds for the box and designing the reed block around those?

In which case, which reeds, and where would you suggest I get them from? 

I'm aware of this thread - regarding the Binci Professional reeds, I am incredibly happy with their performance in my new Eric Martin.  But other suggestions would be welcome.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Going to make a box - what should I know?
« Reply #16 on: June 09, 2011, 01:25:25 PM »

.... so should I start off by buying the reeds for the box and designing the reed block around those?
I think that is a good idea, so you will then have the exact dimensions of the reed plates and will therefore be able to design your reed blocks accordingly.

I'm one of those who has made a 1-row 4-stop box with Emmanuel Pariselle on the EATMT melodeon making courses. We used Binci Pro reeds on those, which were ordered in advance of the course, and very fine they are too. Even though Emmanuel has now run this course many times and has developed dimensioned drawings and jigs to make the reed blocks, there were still minor modifications needed when the reeds actually arrived, due to minor variations in the size of the reed plates, I guess.

I also agree with those who say that it is best to buy the bellows ready made. You wouldn't make the reeds yourself (at this stage, if ever) so similarly leave the bellows to those who are set up for it professionally. The Galassi bellows are very high quality and unless you really, really want to make them yourself, it's not worth the extra time and effort.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Going to make a box - what should I know?
« Reply #17 on: June 09, 2011, 01:31:38 PM »

If using screws you will need to be careful about the type of timber used for the edges of the reed chambers, softer woods like spruce may not give enough grip for the screws.  Emanuel P uses maple.  He also uses a self adhesive gasket material called "olovice adesivio"  I have some of this if you want to try it.
Charlie Marshall also has this
http://www.cgmmusical.co.uk/CGM_Musical_Services/Felt_Leather_Pallets.html#13
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #18 on: June 09, 2011, 03:34:34 PM »

I also agree I wouldn't make reed blocks without the reeds in hand.  Lots of variables between different type reeds.  I also personnally like to have the bellows in hand.  Lot's of different methods to make a dizzying variety of reed blocks. If you can, study a few sets to get an idea how you want to make them, chamber sizes, angles, etc. 

For me and the type I build, by far, the hardest and most trying part was the treble keyboard.  Lots of intricate pieces to deal with and some tedious work in getting the action right.  Axle placement, lever sizes, spring type and placement, and things like that make noticeable differences in action feel.  Again, study some you like. 

If you're like me, you won't know what to look for until you build one.  The first one will make you want to build another one to improve the first, or never go near one again.

Tools I couldn't be without-table saw and drill press. Tools I woulnd't want to be without-routers, band saw, guillotine miter trimmer (like for picture frames).  Tools I won't give up now that I have them-stationary belt sander, drum sander, jointer, milling machine(luxury item).  If you even think you may build a second (refer to previous paragraph), plan on making lots of jigs.  I can't even begin to imagine how much time I've spent on making, adjusting, scrapping, then remaking jigs. You need a system of clamping frames square. Put a LOT of thought into the order of doing things, you really have to plan several steps ahead, somtimes doing a step you think you need to now will mess up a later step.

Be prepared to spend several hours or days making something all undone by a 2 second mistake. The scrap pile gets smaller with each build.

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #19 on: June 09, 2011, 03:39:06 PM »

I'll also add that I've never built anything as tedious, challenging, or frustrating, and caused me several times to want to sell my tools and just go fishing, but it's also, by a long shot, the most gratifying thing I've ever built.  A hard head is a requirement.

Making the first untuned note on my first build made me giggle like a teenage girl just at the fact that it made a sound, and watching someone play it made me beam as if watching one of my kids perform on stage. 

Good luck.
Pages: [1] 2 3 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal