Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3 4 5   Go Down

Author Topic: Metal strap between reedblocks...?  (Read 17526 times)

0 Members and 1 Guest are viewing this topic.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Metal strap between reedblocks...?
« on: August 29, 2011, 10:17:42 PM »

Just wondering if someone can clarify for me the intended use of the small metal strap that is sometimes seen nowadays between adjacent reedblocks in the newer melodeons.....are they there to prevent the reedblocks from physically jarring loose from impacts or handling, or are they installed to mitigate some sort of acoustic overtone or harmonic, etc..... ???
Logged

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Metal strap between reedblocks...?
« Reply #1 on: August 29, 2011, 10:27:22 PM »

If it's the same sort of thing I have in my Scarlatina, it seems to be to ensure that the reed blocks remain at the right distance apart and opposite the correct holes. Over to the experts - Mr Ellis? Theo?
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal strap between reedblocks...?
« Reply #2 on: August 29, 2011, 11:28:09 PM »

If it's the same sort of thing I have in my Scarlatina, it seems to be to ensure that the reed blocks remain at the right distance apart and opposite the correct holes. Over to the experts - Mr Ellis? Theo?

Not quite,  there should be locating blocks on all sides of the reedblocks that ensure they sit in the correct position with the holes lined up.

The purpose of the metal strap is to prevent a resonance effect that can result in the tremolo not working properly.  This does not affect every box, and it usually only affects one note,  but when it does happen it can be quite horrible.  If you are tuning, then the usual symptoms are that the reeds play perfectly on the tuning bench, but once inside the instrument the affected note just sounds bleurgghh, I can't think of a better description.   Fit a strap and hey presto, the problem vanishes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Metal strap between reedblocks...?
« Reply #3 on: August 30, 2011, 09:07:32 AM »

If you are tuning, then the usual symptoms are that the reeds play perfectly on the tuning bench, but once inside the instrument the affected note just sounds bleurgghh, I can't think of a better description.   Fit a strap and hey presto, the problem vanishes.

As I've always understood it, the vibrations at the base of one reed are transmitted via the block to the other reed and are trying to pull it into sync, making an irregular warble instead of the smooth beat between the two reeds. I suppose the block is usually too stiff to transmit much vibration, but has a resonant frequency where it can do so.
Strapping the blocks together changes the resonant frequency and adds some damping, at minimum extra cost and weight.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal strap between reedblocks...?
« Reply #4 on: August 30, 2011, 09:09:40 AM »

There we go, theory and practice in unison!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Metal strap between reedblocks...?
« Reply #5 on: August 30, 2011, 09:21:07 AM »

I can testify to the effectiveness of the reed-block strap. A few weeks ago, on the advice of Theo, I made and fitted a narrow brass strip connecting the top of the three reed blocks of a three-voice instrument which I was putting into 'Dedic' tuning with a very light tremolo.

Although I was tuning with the reed-blocks in situ and the tremolo seemed OK on the bench, as soon as the instrument was completely reassembled, on certain notes the light tremolo disappeared, as the adjacent reeds concerned 'pulled' each other into a unison. Fitting the brass strap not only instantly cured this problem but even better, it evened out the whole tone quality of the instrument, making a brighter and more consistent sound over the whole range. I was amazed by just how much improvement such a simple modification made. Definitely to be recommended!

Thanks again for the advice, Theo!

Edit:
I guess the science behind this is that the sound generation of the free-reed set-up is caused by the reed tongue 'chopping' the airstream into packets. The more rigid the reed-block structure, then the more energy will be transfered to the moving airstream. In a poorly supported, 'sloppy' reed-block structure, some of the energy from the reed tongue will be wasted as it goes into making the reed block vibrate, leaving less energy available to be transfered to the airstream. So ideally the reed-block assembly needs to be as rigid as possible. I wonder how it would perform if the whole set of reed-blocks were to be cast/machined/3D-printed out of a single starting piece with supporting struts at each end and in the middle?
« Last Edit: August 30, 2011, 09:38:39 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Metal strap between reedblocks...?
« Reply #6 on: August 30, 2011, 10:01:36 AM »

The old Hohners I've worked on had, for want of a better description, headless panel pins wedged between the blocks. I presume they do the same job as a strip screwed down across the top of the blocks?

Placement and number of these pins seems to vary quite a bit, I've seen up to three between a pair of blocks (and as few as none!) and the spacing between them is uneven. Would they have be placed next to the affected reed plates? Whenever I've removed any of these I've always put pencil marks on the blocks to ensure they go back in the same place.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal strap between reedblocks...?
« Reply #7 on: August 30, 2011, 10:18:02 AM »

The old Hohners I've worked on had, for want of a better description, headless panel pins wedged between the blocks. I presume they do the same job as a strip screwed down across the top of the blocks?

Placement and number of these pins seems to vary quite a bit, I've seen up to three between a pair of blocks (and as few as none!) and the spacing between them is uneven. Would they have be placed next to the affected reed plates? Whenever I've removed any of these I've always put pencil marks on the blocks to ensure they go back in the same place.

I'm sure these do the same job.  The ones I've seen are just short lenths of thin steel rod.  I believe that only one of these is needed in each gap between blocks, and I don't think the exact position is important, except that its is usually low reeds that are affected by the warble so it seems sensible to place the rods or straps nearer to the low notes than the high notes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Metal strap between reedblocks...?
« Reply #8 on: August 31, 2011, 12:33:29 AM »

Edit:
I guess the science behind this is that the sound generation of the free-reed set-up is caused by the reed tongue 'chopping' the airstream into packets. The more rigid the reed-block structure, then the more energy will be transfered to the moving airstream. In a poorly supported, 'sloppy' reed-block structure, some of the energy from the reed tongue will be wasted as it goes into making the reed block vibrate, leaving less energy available to be transfered to the airstream. So ideally the reed-block assembly needs to be as rigid as possible. I wonder how it would perform if the whole set of reed-blocks were to be cast/machined/3D-printed out of a single starting piece with supporting struts at each end and in the middle?


True, although remember that the sound of a pure siren tone is not necessarily pleasant... a lot of the timbre does come from the body. Whether that is absorption or resonance of course I have no idea, but I think that it's a mistake to assume that an utterly rigid, utterly reflective casing is the perfect solution.

Interesting theory about the reedblocks Anahata, makes a lot of sense (:)
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Metal strap between reedblocks...?
« Reply #9 on: August 31, 2011, 12:59:09 AM »

These posts are what I have been seeking  (:)  Reminds me very much of a device marketed for guitar called the JLD Bridge Doctor, which has a two-fold purpose. One is to help correct the 'belly' that happens on a flat top guitar, and secondly, it profoundly improves the sound of the guitar as well by transmitting audio vibrations to the outer periphery (sides and back). Having installed these in a couple of guitars, I must say that I was astonished at the clarity and brilliance that this device brought forth. It seems to operate in a similar fashion to the soundpost of a violin.  
   I'm going to try some strap experiments in a couple of my boxes to see what may come of it. I'm hoping that this might be a way to add clarity to the reeds.
« Last Edit: August 31, 2011, 01:01:51 AM by j.w.forrest »
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Metal strap between reedblocks...?
« Reply #10 on: August 31, 2011, 12:43:14 PM »

Edit:
I guess the science behind this is that the sound generation of the free-reed set-up is caused by the reed tongue 'chopping' the airstream into packets. The more rigid the reed-block structure, then the more energy will be transfered to the moving airstream. In a poorly supported, 'sloppy' reed-block structure, some of the energy from the reed tongue will be wasted as it goes into making the reed block vibrate, leaving less energy available to be transfered to the airstream. So ideally the reed-block assembly needs to be as rigid as possible. I wonder how it would perform if the whole set of reed-blocks were to be cast/machined/3D-printed out of a single starting piece with supporting struts at each end and in the middle?


True, although remember that the sound of a pure siren tone is not necessarily pleasant... a lot of the timbre does come from the body. Whether that is absorption or resonance of course I have no idea, but I think that it's a mistake to assume that an utterly rigid, utterly reflective casing is the perfect solution.

Interesting theory about the reedblocks Anahata, makes a lot of sense (:)

All the real quantitative work that has been done suggests that more rigidity and reflectivity is best for free-reed instruments, the last thing you want is resonances absorbing energy from or coupling with the reed (which is exactly the problem that the strap solves).

Normally the reed blocks are only clamped to the case at the ends, and the reed which have the "warble" problem usually seem to be towards the middle of the block where it's least rigid, so my suspicion is that the problem is a torsional resonance along the reed block (which one of the notes is almost bound to hit) excited by the beating between the two reeds on opposite sides of the block. This will also be made worse because the reeds are mounted "tips-up", so the  forces are generated at the top of the block where the main reed movement is -- if so, "tip-down" mounting would help but may cause other problems.

So anything that braces or damps the middle of the block against twisting will probably fix the problem -- the "best" solution would probably be a strap that not only linked the blocks but continues downwards to the strong point in the corner where the soundboard meets the case.
« Last Edit: August 31, 2011, 12:47:13 PM by IanD »
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Metal strap between reedblocks...?
« Reply #11 on: August 31, 2011, 02:43:51 PM »

Normally the reed blocks are only clamped to the case at the ends, and the reed which have the "warble" problem usually seem to be towards the middle of the block where it's least rigid, so my suspicion is that the problem is a torsional resonance along the reed block (which one of the notes is almost bound to hit) excited by the beating between the two reeds on opposite sides of the block.
.
.
So anything that braces or damps the middle of the block against twisting will probably fix the problem -- the "best" solution would probably be a strap that not only linked the blocks but continues downwards to the strong point in the corner where the soundboard meets the case.
Ian - I'm sure you are right. I think this is confirmed by the traditional one-row Cajun-type construction, which do not seem to suffer from the resonance problem, at least not to anywhere near the same degree, to my knowledge. Here, the vertically standing reed block (which carries two of the banks of reeds) is glued along its entirely length directly to the soundboard, so there is much less scope for torsional movement. The other two reed blocks are mounted horizontally and similarly glued directly to the soundboard. Cajun boxes are also generally renowned for their powerful sound, again probably testament to this method of construction as much as anything else.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Metal strap between reedblocks...?
« Reply #12 on: August 31, 2011, 08:25:32 PM »

  Well, I did it. After reading the comments posted, I was compelled to try out some straps and find the results.
   My problem child:  old Hohner 3-row.....basses overpowering the treble, lots of trebl-y overtones from the basses, almost 'raspy' sounding. On the treble side, notes a bit timid, chords 'mushy', indistinct. I had attributed this to the fact that the reedplates were secured by screws on leather gaskets, rather that waxed directly to the block.
   After installation: basses and left hand chords much more compact and distinct. Treble notes and chords much more distinct. Improved balance between treble and bass. I am able to achieve similar volume with less effort, allowing me to play with a lighter touch. The best word to describe the change is that now the box is focused, where before it was blurred.
   Used some stuff on hand for the job. The bass side was made from a piece of heavy gauge perforated steel tape about .035" thick. It was bent precisely to fit the blocks so that there was no strain imposed when screwing it down. The screws are about 1/4" long, and only partially penetrate the upper timber of the block. The treble strap is similar material, but only about .015" thick. Some pic's below. Excuse me now, because I have to go back and play some more. It's like having a new box  (:)

Edit: Also a pronounced brightness in the treble reeds! Eureka!
« Last Edit: August 31, 2011, 08:48:53 PM by j.w.forrest »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal strap between reedblocks...?
« Reply #13 on: August 31, 2011, 09:15:55 PM »

It's also worth checking that the projection at the end of the block opposite the fixing screw is a good fit under the wooden bar that locates it.  Take up any slack with paper or card shims.   If the reedblocks are loose they will be able to move and vibrate, and will be liable to leak air from below.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andrew Wigglesworth

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1101
  • 07
    • My website
Re: Metal strap between reedblocks...?
« Reply #14 on: August 31, 2011, 09:46:19 PM »

Got me bit of metal bent to shape, put some holes on it (need to file off the burs). I need to discover/go out and hunt for some little screws though. None of the ones in my toolboxes are quite small enough. I'll have to wait a day or two to see what it does for my three voice box.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Metal strap between reedblocks...?
« Reply #15 on: August 31, 2011, 09:52:58 PM »

Good thread.

@JW Forrest: "It was bent precisely to fit the blocks so that there was no strain imposed when screwing it down."
You have it right there. This is crucial.

@you other guys: We seem to be in accord. I am fascinated by this phenomeneoemenem and have been experimenting with reed-blocks made from Rachel's Organic Yogurt.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Metal strap between reedblocks...?
« Reply #16 on: August 31, 2011, 10:18:36 PM »

I need to discover/go out and hunt for some little screws though. None of the ones in my toolboxes are quite small enough.

Yes....they are quite difficult to find these days. Slightly less scarce than hand-forged nails! Although CGM offers an assortment. If you find other sources, please post!


@you other guys: We seem to be in accord. I am fascinated by this phenomeneoemenem and have been experimenting with reed-blocks made from Rachel's Organic Yogurt.

How's that working out, Rees?
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Metal strap between reedblocks...?
« Reply #17 on: August 31, 2011, 10:20:57 PM »

messy but very tasty
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Metal strap between reedblocks...?
« Reply #18 on: August 31, 2011, 10:24:20 PM »

It's also worth checking that the projection at the end of the block opposite the fixing screw is a good fit under the wooden bar that locates it.  Take up any slack with paper or card shims.   If the reedblocks are loose they will be able to move and vibrate, and will be liable to leak air from below.

Good call, Theo....I have an old Supertone I am re-doing, and it has this condition. I was thinking of adding a bit of veneer to the top of the projection, and sanding down to a snug fit.
Logged

Andrew Wigglesworth

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1101
  • 07
    • My website
Re: Metal strap between reedblocks...?
« Reply #19 on: August 31, 2011, 10:30:02 PM »

messy but very tasty

Does it wobble?
Pages: [1] 2 3 4 5   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal