Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3   Go Down

Author Topic: A Hohner to Refurb and Learn From  (Read 9400 times)

0 Members and 1 Guest are viewing this topic.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: A Hohner to Refurb and Learn From
« Reply #20 on: April 25, 2012, 09:08:06 AM »

New cabinet corners are now made of stainless steel so no plating to worry about.    I push the new corners fully into place (they sometimes need gentle persuasion with a block of wood and a hammer) and then file off the overhang, being careful not to file away any wood.

Thanks Theo - I hadn't twigged that. That's another little job to do, then!

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

chappie86

  • Folker
  • Good talker
  • **
  • Offline Offline
  • Posts: 65
  • Discovering Melodeons
Re: A Hohner to Refurb and Learn From
« Reply #21 on: May 03, 2012, 08:02:52 PM »

Today my ebay purchase arrived in very good condition and the key of GC which I am also happy with.

A couple of questions if anybody can help:-

1) One of the bass buttons is stuck in the elevated position (as seen in the photos) and looks like the button needs pressing further onto the steel rod? Can anybody recommend a good method for doing this? I have checked the rod position inside the box and it looks the same as the others.

2) Is there any way I can stop this old box squeaking on button pressing? Would you recommend using WD40 or similar.

I am really happy and can't wait to get playing some tunes :||:!

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: A Hohner to Refurb and Learn From
« Reply #22 on: May 03, 2012, 08:42:18 PM »

1)  Grip the rod from behind with a pair of long nose pliers then push the button home by leaning the whole thing against a solid surface.
2)  Avoid using any lubricant which leaves an oily or sticky residue like WD40 does.  Powdered graphite in alcohol is good.  The alcohol carries the graphite inside joints and then evaporates leaving a dry lube.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chappie86

  • Folker
  • Good talker
  • **
  • Offline Offline
  • Posts: 65
  • Discovering Melodeons
Re: A Hohner to Refurb and Learn From
« Reply #23 on: May 03, 2012, 08:52:30 PM »

Great thanks for the advice Theo!

 (:)
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: A Hohner to Refurb and Learn From
« Reply #24 on: May 03, 2012, 09:02:19 PM »

Odd squeaks can be maddeningly difficult to cure.  First you have to find the source!  Buttons rubbing on wood is the usual culprit.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: A Hohner to Refurb and Learn From
« Reply #25 on: May 03, 2012, 09:08:49 PM »

Odd squeaks can be maddeningly difficult to cure.  First you have to find the source!  Buttons rubbing on wood is the usual culprit.

Sound advice, took me a long time to learn that the mechanical squeaky noises were not in the metal parts (which is what i sounded like) but usually the buttons rubbing on the finger board, careful alignment cures it most of the time.

chappie86

  • Folker
  • Good talker
  • **
  • Offline Offline
  • Posts: 65
  • Discovering Melodeons
Re: A Hohner to Refurb and Learn From
« Reply #26 on: May 04, 2012, 09:25:17 PM »

Cheers guys. I think it is Deffinatly the wood on buttons making the noise.

Can anybody recomend any really good tunes to learn on a G/C? I am currently learning a French song called Zelda. Good fun to play but lots of practice required :||:!

Chappie
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: A Hohner to Refurb and Learn From
« Reply #27 on: May 07, 2012, 09:19:52 AM »


... but even that is not rocket surgery.

Unlikely to be brain science, either, then?  >:E
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

chappie86

  • Folker
  • Good talker
  • **
  • Offline Offline
  • Posts: 65
  • Discovering Melodeons
Re: A Hohner to Refurb and Learn From
« Reply #28 on: May 07, 2012, 04:28:36 PM »

Does anybody have any tips on removing the bellows pins? I have just tried and my long nosed pliers are damaging the pins? are the pins easy to replace now that I have damaged a few of them?

Once I have removed the pins, should the bellows just pull off as there seems to be some resistance on the treble side?

Thanks again,

Chappie
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: A Hohner to Refurb and Learn From
« Reply #29 on: May 07, 2012, 04:39:52 PM »

I use a pair of end cutters to pull bellows pins eg:

End Cutters

If he bellows pins ar stuck rust is usually j problem, I find application of a soldering iron to warm he pin will generally release it.

If you have damaged the pins Charlie Marshall has them in stock.

As to the bellows sticking, you may need to insert a screwdriver or some such between the frame and the end and gently ease the bellows off.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: A Hohner to Refurb and Learn From
« Reply #30 on: May 07, 2012, 04:45:49 PM »

Side cutters, which are similar, can be used as well. I have old flat pallet knife that I use to rest the cutters on so I can use some leverage while protecting the finish.
I find this gives me more control. But I'm quite sure Lester has pulled more than I have  >:E
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: A Hohner to Refurb and Learn From
« Reply #31 on: May 07, 2012, 04:47:38 PM »

I use Side cutters too, rest them on one of those backplanes removed from a PC case when you put cards in
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: A Hohner to Refurb and Learn From
« Reply #32 on: May 07, 2012, 04:50:37 PM »

Side cutters, which are similar, can be used as well. I have old flat pallet knife that I use to rest the cutters on so I can use some leverage while protecting the finish.
I find this gives me more control. But I'm quite sure Lester has pulled more than I have  >:E

I would advise against using anything, like side cutters, which you pivot against the casework because, however hard you try, you will eventually damage it. End cutters allow you to pull directly on the head of the pin and to apply the force along the direction of travel

chappie86

  • Folker
  • Good talker
  • **
  • Offline Offline
  • Posts: 65
  • Discovering Melodeons
Re: A Hohner to Refurb and Learn From
« Reply #33 on: May 07, 2012, 05:07:54 PM »

Thanks Lester! I will order some of those straight away.

Do you have any recommendations for returning the pins into the box?

Thanks  :D
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: A Hohner to Refurb and Learn From
« Reply #34 on: May 07, 2012, 05:13:39 PM »

Thanks Lester! I will order some of those straight away.

Do you have any recommendations for returning the pins into the box?

Thanks  :D

I use a hammer, albeit a small one. Mostly the pins just push back in but need a bit of a tap to bed them down.

More on removing pins, if its a psh box I usually cover the pin in a bit of scrap cloth and nip the pin through it to further ensure the finish is protected.

chappie86

  • Folker
  • Good talker
  • **
  • Offline Offline
  • Posts: 65
  • Discovering Melodeons
Re: A Hohner to Refurb and Learn From
« Reply #35 on: May 07, 2012, 05:19:04 PM »

Great thanks for the advice.

Chappie
Logged

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: A Hohner to Refurb and Learn From
« Reply #36 on: May 07, 2012, 05:50:35 PM »

A piece of scrap wood allows you to push the pins home properly without applying any shock or risking making an unwanted dent if you're not careful...
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: A Hohner to Refurb and Learn From
« Reply #37 on: May 07, 2012, 06:14:24 PM »

I use end cutters too - get some really cheap ones from your local market or pound shop as they won't be very sharp and are unlikely to damage your pins. If you have good quality ones it's worthwhile (as long as you don't ever need them to actually cut with!) taking the sharp edges off with a needle file or similar. The ones I use were in a set of umpteen small pliers of various patterns (all useful to have to hand) for next to nothing from Aldi.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: A Hohner to Refurb and Learn From
« Reply #38 on: May 07, 2012, 06:17:27 PM »

I use end cutters too - get some really cheap ones from your local market or pound shop as they won't be very sharp and are unlikely to damage your pins. If you have good quality ones it's worthwhile (as long as you don't ever need them to actually cut with!) taking the sharp edges off with a needle file or similar. The ones I use were in a set of umpteen small pliers of various patterns (all useful to have to hand) for next to nothing from Aldi.

Mine were in a set of 6 different sets of pliers by Draper, can't remember where I bought hm but it may have been Hobbycraft. And as you say the other ones have heir uses as well.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: A Hohner to Refurb and Learn From
« Reply #39 on: May 07, 2012, 06:24:27 PM »

There is a lot of good advice here and some not so good:
Replacing bellows pins should never need a hammer, the danger of this method is that if the bellows are not positioned quite correctly the force applied by hammering can damaged the bellows frame.  Just something firm to push with us sufficient, and of you fell excessive resistance you can stop before doing damage.

Separating tight fitting bellows with a screwdriver!! Argh! Sounds likely to damage the wood.  First try firm pressure with thumbs against the bellows frames, working all round, sometimes it is easier to get the movement started at a corner.  Running a thin blunt blade all round where the surfaces should separate can help.  Failing that a broad thin piece of flat metal can be used to lever the sides apart. Occasionally if poor gasket material has become stuck to both surfaces it is best to slit the gasket with a sharp knife.
« Last Edit: May 07, 2012, 06:34:11 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: 1 [2] 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal