Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Replacing valves  (Read 12530 times)

0 Members and 1 Guest are viewing this topic.

Spikey

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 160
  • NZ
Replacing valves
« on: May 26, 2012, 11:36:11 PM »

Apologies if this has been asked before (have searched and searched and could not find...), but when we took apart my old Hohner Pressed Wood (I think from around the 1940s) to replace the pallet facings the valves started falling out like confetti :o - will it be possible to replace the valves (I think best to replace with vinyl ones as recommended by Lester?) without taking the reed blocks out and having to re-wax them?

I also wondered whether the loose/missing valves could have been causing some of the air leakage?  Is it possible for air to be leaking out through the valves without sounding the reed - still trying to get my head around how the reeds work so this could be a daft question - we have replaced the bellows gaskets as thought this might be where the leak was coming from, but it still seems to leak massively and we can't see where there might be any holes in the bellows - have tried shining a torch through in a darkened room, and holding them close to my face while playing...

Any advice gratefully received (:).
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Replacing valves
« Reply #1 on: May 26, 2012, 11:47:50 PM »

The valves on the back of the reed plate (inside the block) can't be replaced without taking the reed plate off so you are looking at rewaxing to do those.

As for leakage: missing valves won't make the box leak more while you are not pressing any buttons, but as soon as you play a note where the opposite reed is missing its valve, you will be leaking air through that reed, so it is a form of leakage.


Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Spikey

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 160
  • NZ
Re: Replacing valves
« Reply #2 on: May 27, 2012, 02:47:33 AM »

Oh dear...I thought that might be the case - another thing to add to my next Charlie order ::). 

If the missing valves could be a source of the leaking then I think we will wait until (if!) it is back together again, and if it still seems too leaky we can try and tackle the bellows then.

Thanks Anahata

Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Replacing valves
« Reply #3 on: May 27, 2012, 05:40:39 AM »

There are a few places where a box can leak air - bellows-pin holes, pallets not quite seated (though you'd notice a reed trying to sound if that were the case), iffy air-valve, poor joints, small holes or splits in the baseboard (or pallet board, or whatever we're calling it now!), reed blocks not seating properly.......

Does it leak only when you're playing, or does excess air escape if you open & close the bellows without depressing a button?
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Spikey

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 160
  • NZ
Re: Replacing valves
« Reply #4 on: May 27, 2012, 07:59:04 AM »

There are a few places where a box can leak air - bellows-pin holes, pallets not quite seated (though you'd notice a reed trying to sound if that were the case), iffy air-valve, poor joints, small holes or splits in the baseboard (or pallet board, or whatever we're calling it now!), reed blocks not seating properly.......
Thanks GPS - it sounds like a case of 'How do I leak...let me count the ways...', and I think it might be many of these...  Have discovered a small split in the pallet/base board - well it's either that or a woodworm going in a very straight line ;D - it has those too.

Thinking back now to when it was all in one piece it did seem to leak a lot when playing, but not hugely when trying to close the bellows without pressing a button - but I might be remembering this incorrectly.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Replacing valves
« Reply #5 on: May 27, 2012, 09:24:05 AM »

Thanks GPS - it sounds like a case of 'How do I leak...let me count the ways...', and I think it might be many of these...  Have discovered a small split in the pallet/base board - well it's either that or a woodworm going in a very straight line ;D - it has those too.

Run super glue along it to seal it.

Another leakage I have just spent hours finding was on an old box, it sounded to be coming from where the bellows frame met the end but I had replaced the gasket and I knew it was sealing OK. In the end it turned out that where the fondo (other words are available  ;) ) met the casework the varnish or whatever Hohner used to seal this joint had failed and the air was leaking around the joint. Again super glue was my friend.

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Replacing valves
« Reply #6 on: May 27, 2012, 09:42:42 AM »

Thanks GPS - it sounds like a case of 'How do I leak...let me count the ways...'

Unfortunately this is often the case with old boxes: lots of small leaks. To get a real improvement you have to fix them all.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Replacing valves
« Reply #7 on: May 27, 2012, 10:12:27 AM »

Two more potential leaks:
1- via the holes for the screws that hold the keyboard
2- partial failure of the glue jount that holds the bellows frames onto the bellows.

And a third, With very old and much played bellows the valley folds of the bellows can become porous.   This happened to my old 1930s club box,   new bellows made an immediate cure, but only after I had spend hours dealing with all the small leaks outlined above.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Replacing valves
« Reply #8 on: May 27, 2012, 10:19:48 AM »

1- via the holes for the screws that hold the keyboard

When ever I have a keyboard off I install leather washers to prevent this problem. Make them myself with some punches and scrap leather bits. I notice that the Chinese manufacture Pokerworks seem to have glue all over these screws making their removal difficult.

Spikey

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 160
  • NZ
Re: Replacing valves
« Reply #9 on: May 27, 2012, 09:55:28 PM »

Thanks for all of this everyone - has given me a lot more to think about and check - I just hope it's not porous bellows :o...will pass all this on to my chief technical expert (I am just the beautiful assistant - well, the second part anyway).

Another question about valves - on CGM you can get a full set of vinyl valves for a 21 treble / 8 bass two reed melodeon, but there are also Hohner double and triple layer valves - will the set be OK to use, or should I be putting in the double or triple type?  I'm not sure what the difference is and when you would use the different types?
« Last Edit: May 27, 2012, 09:57:38 PM by Spikey »
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Replacing valves
« Reply #10 on: May 27, 2012, 10:04:15 PM »

Quote
met the casework the varnish or whatever Hohner used to seal this joint had failed and the air was leaking around the joint. Again super glue was my friend.

Reed wax is another good (and flexible) sealer, in fact my Club-III had it already inside to finish off the seal after the hide glueing . I`m not sure I`d be happy about squirting water-thin superglue into the edges of a palletboard - but then you`ve fixed far more boxes than I ever wil so who am I to argue  :P
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Replacing valves
« Reply #11 on: May 27, 2012, 11:12:06 PM »

I would avoid using wax or superglue here.  Wax because once the joint is "contaminated" with wax it will be difficult to ever re-make the joint propery with glue. Superglue I avoid superglue (unless there is no alternative) because I react badly to the fumes.

Why not do a proper job and use hide glue? It is cheap, and does agreat job.  A simple gluepot can be made with a baby bottle warmer and a jam jar.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Replacing valves
« Reply #12 on: May 28, 2012, 05:23:35 AM »

Or you can get Titebond Liquid Hide Glue; I'm not entirely sure what it's actually made from, but it's intended for musical instrument & cabinet work without the bother (& smell) of mixing & heating rabbit-skin or pearl glue, but is supposed to have similar properties.  I have a bottle, but I've not yet used it.......

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Replacing valves
« Reply #13 on: May 28, 2012, 05:55:14 AM »

I've tried the liquid hide glue, and have gotten inconsistent results. I'm pretty sure it is regular hide glue with urea added to retard drying.  I wouldn't put much faith in it, I don't think it nearly as strong as regular hide glue, and has a very short shelf life.  Go to some luthier forums and do some searches on it, you'll find that the overwhelming opinion.  There is one called Old Brown liquid hide glue that is supposed to be better.  I have some but don't trust it enough to use it.  I use regular hide glue for many applications, especially where I don't want to mess with clamps (rubbed joints), but am using fish glue more and more.  It has the glass hard drying of hide glue, pulls joints together like hide glue, but has much longer working time.  It has more working time that regular woodworking glue, but a better tack so parts don't slide around when clamping like regular yellow glue.  It is clear under a finish like hide glue. It can be refrigerated to last longer, and can even be frozen. In fact, the more it goes, the more my yellow glue sits on the shelf.

Jeff Hildreth first told me about fish glue, and after doing a lot of research on it and using it for the last couple years, I'm a staunch supporter of it and don't understand why it's not used more. Some think that fish glue will dissolve in humid weather.  I tried to remove some veneer glued with fish glue the day before with a steam iron and finally gave up.  It can be done, but not nearly easily as regular hide glue, and removed my fear of humidity.  A good joint will not be affected by humidity anyway.

For a crack, I actually may use the super glue types(CA), but more likely would use epoxy on the pallet board.  If you're only filling a crack, epoxy (or CA) has better gap filling than yellows glues or animal glues.  I really like thin CA for a crack that is just starting, it soaks in deep and stabilizes the wood.
« Last Edit: May 28, 2012, 06:00:49 AM by blafleur »
Logged

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Replacing valves
« Reply #14 on: May 28, 2012, 05:13:33 PM »

I just bought four more gallons of fish glue; been using it for about 15 years.  I have found nothing better. It beats hide glue.
Four gallons costs about $130 including shipping. That's $32.50 US per gallon. Luthier supply shops sell smaller quantities for a great deal more money. It stores nicely , shelf life quite long, never had any go bad. Even if it freezes, it is still as good as new when brought back to room temperature.  Does not smell as bad as hide glue and needs no glue pot to keep it warm for use.
Comes apart in the usual heat or steam methods. I have yet to find a downside.

As for TITEBOND  "Hide Glue"... forget it.. it's useless. My opinion is that it has no redeeming attributes. Waste of money.



Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Replacing valves
« Reply #15 on: May 28, 2012, 07:41:52 PM »

That's $32.50 US per gallon.

Just over 20 quid for 4/5ths of a gallon, then....... :D >:E
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Spikey

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 160
  • NZ
Re: Replacing valves
« Reply #16 on: May 28, 2012, 08:09:56 PM »

Thanks for all the replies everyone, but could I steer this briefly back to valves? (I need to put in my order!):
Another question about valves - on CGM you can get a full set of vinyl valves for a 21 treble / 8 bass two reed melodeon, but there are also Hohner double and triple layer valves - will the set be OK to use, or should I be putting in the double or triple type?  I'm not sure what the difference is and when you would use the different types?
Does anyone have any wisdom they could share on which valves to use for an old Hohner pressed wood C/F - single, double or triple Hohners (does this depend on what size the reed is?), or will the standard melodeon set do?  The old ones that are falling off are all leather but I want to replace them with vinyl, as this seems the recommended way to go.

Then we can get back to glue ;D.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Replacing valves
« Reply #17 on: May 28, 2012, 08:39:05 PM »

The larger valves (for the larger reeds) have more layers , just pick the valve closest to the size of the reed and trim if necessary (trim all the layers by the same amount)
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Replacing valves
« Reply #18 on: May 28, 2012, 08:48:35 PM »

The larger valves (for the larger reeds) have more layers , just pick the valve closest to the size of the reed and trim if necessary (trim all the layers by the same amount)

Wise words  ;)

Spikey

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 160
  • NZ
Re: Replacing valves
« Reply #19 on: May 29, 2012, 07:23:01 PM »

Thanks everyone (:) - have just heard from Charlie and the CGM 038C valve set contains a selection of 6 different Hohner 3 layer and 2 layer valves so it all sounds good (and hopefully we will be able to install them correctly and the melodeon will too ::)).
Logged
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal