Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: spring tension  (Read 9923 times)

0 Members and 1 Guest are viewing this topic.

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: spring tension
« Reply #20 on: June 20, 2016, 07:23:27 PM »

i've done this on all my ha one-rows, never had to remove or dissemble the action, just release the spring tension before gently persuading the ''kinks.''
Logged

Robyn Foley

  • Member
  • *
  • Offline Offline
  • Posts: 8
Re: spring tension
« Reply #21 on: March 07, 2020, 06:54:51 AM »

Theo and others, I was looking for some instructions on button tension softening, and found this comment on a Cajun site:

".............To loosen springs is easy. I once watched an old Cajun accordion builder take a 12 inch stainless steel ruler, place it's edge into all of the button springs at once, and bend downward in one quick and sure motion which stretched every spring to the exact same tension in about 3 seconds. Smart ole feller. "

Could I please have some comments on whether that would be something to try on my Sander? Any thoughts about it at all.
I spoke to an accordion repairer a couple of states away from me, and he said he would have a go at the springs/button softening, but that he had not done it before.
If I am going to get someone to do it for me, I was hoping they would have done it before, but in case that cannot be, then some clear easy instructions for me to give to someone would be appreciated.

I did see the instructions earlier posted by Syale, however if the 'ruler' method is feasible, that might be something I could present to a first time repairer, or even attempt myself.

Thank you
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: spring tension
« Reply #22 on: March 07, 2020, 08:19:40 AM »

Most Cajun accordions use coil springs. Italian boxes use hairpin springs so the bending process has to be different.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Re: spring tension
« Reply #23 on: January 29, 2026, 04:34:36 PM »

Is here a similar method to add tension to a spring?
Logged
Too many accordions, help!

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: spring tension
« Reply #24 on: January 29, 2026, 06:54:42 PM »

Is here a similar method to add tension to a spring?

The only method I know of is to grab both ends of a single coil spring with pliers and twist the coil in on itself. This will tighten the spring back up again to some degree.
Logged
C#/D player

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: spring tension
« Reply #25 on: January 29, 2026, 07:21:39 PM »

Is here a similar method to add tension to a spring?

The only method I know of is to grab both ends of a single coil spring with pliers and twist the coil in on itself. This will tighten the spring back up again to some degree.

Coil springs can be shortened to increase tension.
Cut off the loop at one end of the coil with a side-cutters. Place the spring on a flat surface and insert two thin knives between the first and second coil.
Hold one knife upright and push the other knife against the first loop until it is at 90 degrees to the coil.
If it's still not strong enough repeat the process.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: spring tension
« Reply #26 on: January 29, 2026, 07:28:38 PM »

Quote
Place the spring on a flat surface and insert two thin knives between the first and second coil.
Hold one knife upright and push the other knife against the first loop until it is at 90 degrees to the coil.

True cutting-edge technology !  ;D
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: spring tension
« Reply #27 on: January 29, 2026, 08:14:30 PM »

Sorry, yes, I should have said that cutting off a coil would create a stiffer spring. I kind of assumed that was obvious. When I’ve lightened coil springs on cajun boxes in the past, and maybe gone just a touch too far, I just coil the spring back in on itself as described for a quick re-stiffening adjustment. Often I just make new springs from a long coil using the same method Rees described.
Logged
C#/D player
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal