Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3 4   Go Down

Author Topic: Pokerwork clacking  (Read 16098 times)

0 Members and 1 Guest are viewing this topic.

stevejay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
Pokerwork clacking
« on: September 23, 2009, 03:13:57 AM »

Hi-

How big a job to improve the button action and eliminate clacking? Any how-to's out there for me to peruse?

imo the Pokerwork has the raw material to be a GREAT sounding box, and although there are fancier looking ones out there and better constructed, they're still the best bang for the buck.

Thanks! ;D
« Last Edit: September 23, 2009, 03:15:45 AM by stevejay »
Logged

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Pokerwork clacking
« Reply #1 on: September 23, 2009, 04:29:55 AM »

I agree


1st  pull the bellows pins on the treble side
next remove the 2 screws that hold the key board on
Next   wiggle the keyboard off
Next on the bottom of the keyboard where the levers clack   you will need to "pad" this

You can cut a piece of leather or cork or felt to the inside length of the cavity and about 1/8th inch thick  3mm
The pad should be about 1 1/4 inches wide...  just wide enough to touch the back of the cavity nearest where your thumb rests

you can glue this in .. I use contact cement....

Once fitted  and glue dried
CAREFULLY wiggle the keyboard back over the buttins..
the bladed levers will crease the material on the way but have faith.. once it is on  it will fit without interference

Screw the fingerboard back on and reassemble the bellows to the frame


Think this out and dry fit the [parts

Perhaps Theo and others will chime in here....

Good luck

I just did another one  last week....  30 minutes   start to finish

Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Pokerwork clacking
« Reply #2 on: September 23, 2009, 08:42:24 AM »

I did it (a 1986 model) much the same as melodeon. It took me about an hour ('having to explore').

Keyboard came off easily enough, and I personally used cardboard. It both stopped the rattle and raised the action a bit - so my fingers didn't go down the holes.  I'd agree in retrospect that leather would be better.

It still bafffles me why Hohner don't do do this in the factory where it'd be a trivial add on. Or the dealers even "adds value". Once you have a template it might be a 10 minute job?

Not sure about that glue. Mine didn't need it and it seems a hostage to fortune ....

Agree with George below that a lighter touch technique obviates the need for this, but I wasn't anywhere near that at the time. Arguably stuffing the keyboard may have held me back in developing it. So there's a counter argument. I love contradicting myself! (Actually I don't) C
« Last Edit: September 23, 2009, 11:21:50 AM by chrisryall »
Logged
  _       _    _      _ 

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Pokerwork clacking
« Reply #3 on: September 23, 2009, 10:43:30 AM »

why not just maximise the clacking - dont press the buttons far enough to 'clack' when you don't want it & press furthur down the hole when you want free percussion!

george :-\
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Sandy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1007
  • 'Musical Landlady'
Re: Pokerwork clacking
« Reply #4 on: September 23, 2009, 11:49:49 AM »

I quite like the clacking on my pokerwork but would rather the buttons didn't go in so far. Not so sure about the bass buttons really clacking on my saltarelle though ???

cheers
Sandy
 (:)

mikesamwild

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 638
  • Melodeon, Button Accordion, Anglo Concertina
Re: Pokerwork clacking
« Reply #5 on: September 23, 2009, 12:14:00 PM »

You can wedge a padded dowel across the levers at a position to get the right height Speeds you up too
Logged
Mike in Sheffield

If music be the food of love -who finds the time?

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Pokerwork clacking
« Reply #6 on: September 23, 2009, 01:23:41 PM »

Most of the noise my pokerwork makes is the pallets whacking against the wood 'soundboard'....especially on the bass side.  I've never had problems with the button levers slamming against the fingerboard.
Logged

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Pokerwork clacking
« Reply #7 on: September 23, 2009, 01:29:48 PM »

For pokerworks with the Hohner one layer leather surface on the palets there is very little to absorb the impact which makes the palets click. If you reface with felt+leather glued together it gives it more dampening and helps to stop some of the racket. The clicky buttons are best cured with layers of felt beneath them.

Cut one sheet of felt to size and use it as a template for others... you can then layer up as many as you like to limit the button depth to you needs. I prefer this to the bar behind the grille method as it provides a more positive feeling action.

It's the underside of the button and leaver which touches the Morris grip thumb side of the keyboard which clacks, as opposed to the arms touching elsewhere.
Logged

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Pokerwork clacking
« Reply #8 on: September 23, 2009, 01:49:52 PM »

For 
 which touches the Morris grip thumb side of the keyboard 

? do all pokerworks have one of these & where is it! for that matter what is the Morris grip??
george ::)
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Pokerwork clacking
« Reply #9 on: September 23, 2009, 02:16:46 PM »

You can wedge a padded dowel across the levers at a position to get the right height Speeds you up too

I did this. It worked OK pro tem

I decided to leave it out as 'advice' and it didn't help the clatter much, and might concevably knock the levers or pads out of balance. My box was OK over the 6 months I did this however. I felt the 'stuffing' solution worked better
Logged
  _       _    _      _ 

stevejay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
Re: Pokerwork clacking
« Reply #10 on: September 23, 2009, 03:06:03 PM »

why not just maximise the clacking - dont press the buttons far enough to 'clack' when you don't want it & press furthur down the hole when you want free percussion!

george :-\

It's not just the clacking, it's aboout the speed. Triplets and rapid runs are not as easy as they might be.

I've got great advice, but I might have a better idea once I've opened it up. I've worked on concertina action (The Bastari fix) but not melodeons. 
Logged

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Pokerwork clacking
« Reply #11 on: September 23, 2009, 04:06:18 PM »

One great "feature" of the Pokerwork and many other Hohner boxes is their simple construction allowing for customizations. A bit like taking a car to a speedshop to upgrade and ajust its mechanical elements.

I did these kind of fixes to an old HA112, re-surfaced the pallets, etc and it's a completely different playing experience. Same with my Corona 2, putting felt under the keyboard.
« Last Edit: September 23, 2009, 04:52:39 PM by québécois »
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

stevejay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
Re: Pokerwork clacking
« Reply #12 on: September 23, 2009, 04:43:02 PM »

I didn't mean a better idea than your advice, I meant a better understanding of the mechanisms in play. My above post sounded pompous ::)
Logged

ACE

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 535
Re: Pokerwork clacking
« Reply #13 on: September 23, 2009, 04:57:47 PM »

Teach your missus to accompany you on the spoons, or even better on the bones. You will not worry about clacking again after you hear those.
Logged
Paddy Clancy, paddlewheel gob iron cheepo g/d anglo

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Pokerwork clacking
« Reply #14 on: September 23, 2009, 08:04:08 PM »

Most of the noise my pokerwork makes is the pallets whacking against the wood 'soundboard'....especially on the bass side.  I've never had problems with the button levers slamming against the fingerboard.

Coincidentally I was just thinking about exactly the same subject, and wondering whether to post a question.

On mine the buttons have to be pushed a good 1/4" below the surface of the fingerboard board before hitting anything, but the noise comes when the buttons are released.   I did try putting something under them to reduce the travel, trouble was that if was thick enough to stop the buttons depressing below the surface, I could get the action re-assembled.   I used the "dowel-across-the-action" method for a bit, but found the levers starting to bend although I wouldn't say I was rough on the instrument.   I did like the reduced travel, but started to come to the conclusion I'd either need to leave it as-is or make a new fingerboard.

Tony S
Logged
Tony S

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Pokerwork clacking
« Reply #15 on: September 23, 2009, 08:05:52 PM »

You can wedge a padded dowel across the levers at a position to get the right height Speeds you up too

Even better place for such a "limiter" is underneath the levers, between them and the edge of the casing.  There it is nearer the fulcrum and you can even put more packing under alternate levers to compensate for the differing lengths/button heights on each row.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pokerwork clacking
« Reply #16 on: September 23, 2009, 08:15:10 PM »

I've tried/seen both methods, and I don't use either.  Packing under the buttons is limited by the requirement to be able to get the buttons back into the fingerboard.  The rod across the upper levers can lead to levers being bent by a player with heavy fingers, and you tend to get a softer effect in the centre of the fingerboard as the rod flexes.  You can also get noise if the rod contacts the grill.

I'm just about to do the business on an Erica, so I'll take some photos as I go.   The method I use is not my own idea, it came from the late Richard Morse of the Button Box.  This places a strip of soft wood under the levers beneath the fingerboard.  The pictures will make it clear.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

HallelujahAl

  • Guest
Re: Pokerwork clacking
« Reply #17 on: September 23, 2009, 08:26:15 PM »

Quote
I'm just about to do the business on an Erica, so I'll take some photos as I go.   The method I use is not my own idea, it came from the late Richard Morse of the Button Box.  This places a strip of soft wood under the levers beneath the fingerboard.  The pictures will make it clear.

Would really appreciate that Theo! Thanks, AL.
Logged

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Pokerwork clacking
« Reply #18 on: September 23, 2009, 09:03:20 PM »


I'm just about to do the business on an Erica, so I'll take some photos as I go.   The method I use is not my own idea, it came from the late Richard Morse of the Button Box.  This places a strip of soft wood under the levers beneath the fingerboard.  The pictures will make it clear.

I suspect that we are talking about the same method here.
I have not tried either of the other ideas, forseeing the problems you mention, but did hear that it was feasible to fit felt into the keyboard by removing it and the pallets together.
Mind you I have a lot to learn, still have to find out how to fit new bushes to the treble end?
 (Ebay item 270458363808)
Regards, Bruce
« Last Edit: September 23, 2009, 10:26:38 PM by Theo »
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Pokerwork clacking
« Reply #19 on: September 23, 2009, 09:16:36 PM »

I've tried/seen both methods, and I don't use either.  Packing under the buttons is limited by the requirement to be able to get the buttons back into the fingerboard.  The rod across the upper levers can lead to levers being bent by a player with heavy fingers, and you tend to get a softer effect in the centre of the fingerboard as the rod flexes.  You can also get noise if the rod contacts the grill.

I'm just about to do the business on an Erica, so I'll take some photos as I go.   The method I use is not my own idea, it came from the late Richard Morse of the Button Box.  This places a strip of soft wood under the levers beneath the fingerboard.  The pictures will make it clear.

I have a Theo modded Erica and it is all you could want on clackyness and button travel. Was going to take some photos next time I met up with it* but Theo wll do it better.

*Anyone want an Erica it's in the back of my car in Terminal 3 short stay 'til late Friday but you will have to workout which car - mind you it may be the only one with baldricks on the back seat
Pages: [1] 2 3 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal