Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3 4   Go Down

Author Topic: Presswood Pokerwork Rebuild  (Read 21176 times)

0 Members and 1 Guest are viewing this topic.

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Presswood Pokerwork Rebuild
« Reply #20 on: December 10, 2010, 04:49:11 PM »

I'll check with my friend and see if she can't write a brief description, and I'll post it here. I just drop them off and pick them up!

Bob
Logged

strad

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 418
Re: Presswood Pokerwork Rebuild
« Reply #21 on: December 10, 2010, 05:09:54 PM »

Just googled Ultrasonic Cleaner and they're quite cheap now. We used to clean oscilloscopes in an ultrasonic bath at one place I worked. Sparkle, sparkle until they were switched on! Then the liquid lurking in the mains transformer caused some interesting effects. But for things like reeds I would imagine they'd be really good. Not a lot of use for bellows, though.

Nigel
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Presswood Pokerwork Rebuild
« Reply #22 on: December 10, 2010, 05:21:09 PM »

I've considered using an ultrasonic cleaner fro reeds,   but I have one worry about making the metal so clean that it becomes more prone to corrosion in the longer term.  This could be especially a problem because of the possibility of galvanic reactions between the two different metals.  I'm sure there are ways to avoid this with the right cleaning solutions, and use of a de-watering/corrosion inhibiting solutions.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Presswood Pokerwork Rebuild
« Reply #23 on: December 10, 2010, 08:07:05 PM »

The cheap ones really aren't worth it, you need one of the proper industrial ones that start at a couple of hundred quid.

I bought a £40 one, (when it was on sale for £25), and I've tried different cleaning solutions and none of them really shift stubborn rust, wax or glue. They make it a lot easier to remove but they don't get very good results, even cleaning for ages and ages in pretty strong solvents. Boiling in plain water is more effective and cheaper. In both cases I applied camelia oil to the reed tongues and no problems with rusting so far.

I tried boiling some reeds that I thought were beyond redemption in pickling vinegar and after only a few minutes nearly all the rust was gone....along with the blue oxide layer on the base and undersides of the tongues.... ::)
Logged

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Presswood Pokerwork Rebuild
« Reply #24 on: December 10, 2010, 08:54:00 PM »

The cheap ones really aren't worth it, you need one of the proper industrial ones that start at a couple of hundred quid.

I bought a £40 one, (when it was on sale for £25), and I've tried different cleaning solutions and none of them really shift stubborn rust, wax or glue. They make it a lot easier to remove but they don't get very good results, even cleaning for ages and ages in pretty strong solvents. Boiling in plain water is more effective and cheaper. In both cases I applied camelia oil to the reed tongues and no problems with rusting so far.

I tried boiling some reeds that I thought were beyond redemption in pickling vinegar and after only a few minutes nearly all the rust was gone....along with the blue oxide layer on the base and undersides of the tongues.... ::)

Cool, I suspected as much.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #25 on: December 10, 2010, 09:17:05 PM »


I tried boiling some reeds that I thought were beyond redemption in pickling vinegar and after only a few minutes nearly all the rust was gone....along with the blue oxide layer on the base and undersides of the tongues.... ::)

Can't you apply steel bluing to restore that oxide layer again? Never tried the stuff before so I don't know how it works. Only enough knowledge to get myself into trouble.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Presswood Pokerwork Rebuild
« Reply #26 on: December 10, 2010, 11:43:13 PM »

DO NOT trust them to clean CD's as they claim to be able to do! Fortunately I experimented on one of the copies I make for the car, but the surface bubbled up quite alarmingly. Otherwise ours is not quite as good as the manufacturer says it is - if that's not an oxymoron.  :|glug
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Presswood Pokerwork Rebuild
« Reply #27 on: December 11, 2010, 12:19:09 AM »

I'm glad I bought mine when it was on sale, a complete waste of money. I thought it would help me avoid loads of tedious scrubbing and creating fine dust but all it did was make it slightly easier whilst adding considerably to the overall time it took to clean them. I tried it with water, water with washing up liquid, several special, (and expensive), cleaning solutions, neat and diluted meths and even coca cola.

I really recommend boiling in slightly diluted white vinegar for rusty levers and action parts though, works a treat. However, I would also recommend doing it outside on a camping stove and not in the kitchen, the smell it creates is truly vile. I needed a hell of a lot of Febreze, scented candles and open windows...

I haven't put the reeds back in the box yet but they appear to be OK and sound fine when plucked with a pinger. The removal of the oxide layer alarmed me and I pulled them out straight away but I don't see why the reed shouldn't be alright without it, other than making the underside and base of the tongue a bit more susceptible to rust. The top of the tongue never has an oxide coating and boxes shouldn't really be subjected to the kind of conditions that cause rust anyway.
Logged

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Presswood Pokerwork Rebuild
« Reply #28 on: December 11, 2010, 09:11:46 PM »

Here's the info my clockmaker friend sent me about what she does with my reeds while they're in her care. Feel free to ask questions, but I will likely not know the answers! (If I do receive any questions, I will collect them and pass them along.)

I will preface this by saying that I've been fortunate in not having encountered reeds with a great deal of rust on them -- the majority of what I have found, I've been able to scrape off with the broken end of a bamboo skewer or a sanding pencil, etc., prior to cleaning.

I have not  encountered any subsequent rust accumulation after doing this, but then again, they do not live in an environment that is conducive to rust.  And the experiment is only two years old -- who knows, they may collapse in an oxide cloud next year.

In other words, I'm not endorsing this as the best way to do it. (Insert disclaimers here.) I'm a hobbyist at this, but it seems to be working...for now. Until something better happens to comes along. Your mileage may vary.
________________________________________________________________________________


Clockmakers technique for cleaning reeds:

Soak individual read blocks in a 50-50 mix of mineral spirits and xylene for 1/2 to 1 hour to soften the wax.  Caution xylene is nasty, do this out side and/or wear a respirator.  Do not breath in the xylene. Wearing nitrile gloves (do not use laytex as they are not a barrier to xylele) remove one read block at a time from the solvent mix and brush the semi dissolved wax off onto paper towels then set aside to let the rest of the solvent evaporate.  There will be a slight dirty haze left on the reeds.

Lay out reed blocks in basket of ultrasonic tank (it doesn’t matter if they overlap) then submerge and run tank for 3 to 5 minutes.  Rinse with running water then dunk in denatured alcohol.  Dry 3 or 4 blocks at a time on a towel using a hair dryer, flipping often.  Done.

The solution I use in my ultrasonic is Polychem Deox-007 nonammoniated cleaning concentrate.  It is diluted 7 parts water to 1 Polychem.  One gallon from “Merritts” (clock repair supplier) is about $24.00.  I’ve also used Historic Timekeepers concentrate, again diluted 7 to 1, a pint from “Timesavers” is $9.00.  I’ve heard that other detergents/degreasers like Simple Green work as well but I have not tried them.  Just be careful of creating excess bubbles by the ultrasonic.  If I didn’t have the ultrasonic tank Simple Green and a tooth brush I think would work fine.

Look for ultrtasonic tanks at Harbor freight.  They go on sale and are just fine for occasional use (either the little jewelry ones or the bigger gallon size).

For removing rust from linkage arms I’ve soaked them in Captain Lee’s Rust Away from SPRA’-STRIP, inc.  It is a phosphoric acid solution.  Or a mechanical method is using 3M Radial Bristle Disc in a dremel tool (white 120 grit to blue 400 grit).  I get these from Jewelry suppliers like Rio Grand or the Hobby supplier Micro-Mark.
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #29 on: December 12, 2010, 07:08:13 AM »

I made good progress today.

I removed and disassembled the treble mechanism, and made a small table for holding all the parts separately. The springs for the front row were kept separate from those for the back. I've uploaded a photo of my table below. The rust was removed from all the keys and other mechanical parts. Once the parts were cleaned, I applied a light coat of wax to provide some protection from rust. The wax also provides a minimal lubricant though it's not sticky and will not attract dust. Glad I remembered that trick.

Added later: Wax - I used a floor wax with Carnuba, not reed wax. The canuba based wax dries to a hard finish and will help protect the steel. I use it on our long swords for my morris team. The wax really helps the blades to slide against each other when making a lock.

All the pallets for bass and treble are now cleaned, the old leather removed and surfaces sanded, ready for new felt and leather. Still waiting for the box from CGM.

I also made a small table to fit over the bellows frame as a mini tuning table. I'll post a photo to my Picasa folder tomorrow.

Tomorrow I'll clean up the bass mechanism and reassemble the treble mechanism. The I'll probably start removing the old bellows tape.
« Last Edit: December 12, 2010, 05:23:47 PM by Telemorris »
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #30 on: December 13, 2010, 04:55:04 PM »

Bellows repair questions:

I've been looking through the archives about removing bellows papers and tape. I started stripping off the original bellows tapes. They look and feel like paper with a coating of some kind on the outside. I'm trying to remove them dry by gently separating them from the layer of paper underneath with a thin tool that can slide between the two layers. I've tried using a damp sponge to put some water on the old tape only but that doesn't seem to work. The coating seems to prevent the water from soaking through the tapes. Any water that makes it onto the old decorative papers causes those papers to pill up if I rub with the lightly dampened sponge to try to get the tape residue off.

I've been fairly successful with the thin tool at separating the tape from the paper though the paper underneath is sometimes coming away in spots where the glue did not bond to the cardboard. At this point I'll need to replace the papers in the folds as well - I wasn't all that thrilled by the brown and white spotted paper in the first place and was thinking of putting on something new anyway.

Please advise about techniques for removing the paper tape and the old layer of original paper safely without harming the bellows card underneath. The bellows card itself is in good shape. Is it best to stick to a dry technique to strip the old tapes, and use fine sandpaper to get the old bits of glue and paper off? Do I cut strips of cloth the correct size of the tapes, wet them and let them sit on the tapes for awhile or is that likely to cause problems with the bellows?

If I'm going to replace the bellows papers and tape, do I need to completely remove the old paper or can I put new paper over the old? What's the best sequence of tasks for chasing leaks coupled with tape and paper removal? Should I remove the tape and paper as much as possible but wait to re-cover the bellows until I get gaskets and pallets installed to test for air leaks?

Tallships, any advice would be greatly appreciated. Did you strip off down to the original card stock? It's hard to tell from the photos in your thread.
Thanks
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Presswood Pokerwork Rebuild
« Reply #31 on: December 13, 2010, 05:48:29 PM »

I'd be interested in this as well. My imperial needs retaping but I'm determined that it doesn't need repapering, as that seems like a pretty horrible job. Haven't started trying to remove yet.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Presswood Pokerwork Rebuild
« Reply #32 on: December 13, 2010, 06:09:08 PM »

You should have asked some of these questions before you started the job (:)
It should be possible, though tedious, to remove the paper "tape" without damaging the covering paper.
Sometimes, but very rarely, the taping will almost fall off but usually gives the problems you mention to varying degree.
You need to split and tear off as much of the waterproof coating first, so that the remaining "tape" can be dampened enough to soften the glue. Once this is achieved it is fairly simple to scrape/wipe the residue off without damaging the paper covering the folds.
Once you have done this you need to clamp the bellows until they are thoroughly dried out!
One problem with recovering the decorative paper, apart from making the bellows stiffer, is that by rights it should go on before and under, the metal corners, so you may be in for some fiddly tailoring.
As regards air leaks, again, you should have looked before you started the job. If the bellows were originally airtight retaping them should not create any leaks.
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #33 on: December 16, 2010, 07:35:24 PM »

Removal of old paper and tapes is almost finished on the Presswood bellows. The original paper was only partially attached in many areas so removal has been a case of tearing the paper off to find untouched card stock underneath. I'm down to the card and gussets on three sides and am about to finish the fourth.

I'm not finding it as tedious as others seem to. Something of a meditative frame of mind hits me as I'm doing the fine details lifting paper from the edges of the metal corners. I have not removed the corners having seen a post from Theo in the archives warning against that. I'll need to figure out how to cut and attach the papers at the corners once I'm to the papering stage since I'll be attaching around the edges of the metal corners. Any suggestions for how to cut the papers at the corners?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Presswood Pokerwork Rebuild
« Reply #34 on: December 17, 2010, 12:51:29 AM »

having seen a post from Theo in the archives warning against that.

Yes, I seem to remember that he was quite emphatic in that warning ;D
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Presswood Pokerwork Rebuild
« Reply #35 on: December 17, 2010, 08:37:02 AM »

Sometimes the corners are fairly loose, if they come off easily it may be worthwhile
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #36 on: December 19, 2010, 02:43:05 AM »

Theo,

The corners are all quite tight so I've removed the paper up to the joint between the metal and the leather.

I've removed the reeds from the reed blocks and am in the process of cleaning the wax and old valve glue off. One post in the archives mentions "white spirits" for removing wax. Would that be the the same thing as denatured alcohol here in the US?

Also, how clean do I need to get the reed blocks and the reeds? I've scraped the wax off down to the surface of the wood but there's still some residue.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Presswood Pokerwork Rebuild
« Reply #37 on: December 19, 2010, 06:02:02 AM »

Denatured alcohol is called "methylated spirit" in the UK; "white spirit" is turpentine substitute (NOT turpentine!!!), derived from paraffin (kerosene), once used almost universally for cleaning paintbrushes and still readily available in ironmongers (that's hardware stores over there!) and d-i-y outlets.  I believe it's also called Stoddard solvent in some places.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Presswood Pokerwork Rebuild
« Reply #38 on: December 19, 2010, 09:50:01 AM »

I don't like the idea of using solvents to clean wax off reeds or blocks.  My method is to scrape off the wax with a blunt knife (actually an old kitchen knife with a broken blade with the broken end ground to a right angle) then I give the reedblocks and reeds a good scrub with a soft wire brush designed for cleaning furniture after chemical stripping of old paint.    Brushes for sued shoes also work well.  Finally brush off loose dust with a 1/2" paintbrush.  If you have a compressed air supply to blow everything clean that would be ideal.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Presswood Pokerwork Rebuild
« Reply #39 on: December 19, 2010, 10:39:49 AM »

I don't like the idea of using solvents to clean wax off reeds or blocks. 
Is that because it opens them up to corrosion, or a different reason? Interesting because there was a mention somewhere of using an ultrasonic bath which might have a similar effect.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."
Pages: 1 [2] 3 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal