Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4   Go Down

Author Topic: Presswood Pokerwork Rebuild  (Read 21173 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Presswood Pokerwork Rebuild
« Reply #40 on: December 19, 2010, 10:46:49 AM »

I was concerned on several grounds, but mainly that its just not necessary.   I've rebuilt dozens of old boxes over the past few years and the worst problems I have had with reeds is an occasional bit of loose dust getting stuck in a reed when its first played. 

Using solvents have the following downside:
possible long term increase in corrosion risks.  This is a bit of an unknown, but a risk I'd rather not take.
the risk of solvent washing debris into the more inaccessible crevices,  not a problem with ultrasonic cleaning
fire risk
health risks of inhaling solvents

But mainly its just not necessary in the vast majority of cases.

I have thought about using ultrasonic cleaning, but if I did the liquid would be water/detergent based rather than using organic solvents.


Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Presswood Pokerwork Rebuild
« Reply #41 on: December 19, 2010, 04:05:19 PM »

I have used ultrasonic cleaning on jewelry / watch / instrument parts and it certainly reveals defects such as poor stone settings either mechanical or 'glued' and can clean enough to allow crack detection to reveal fatigue fractures at the root of teeth etc. in terms of preventitive maintenance fetching accumulated crud or rust out of a fractured reed might allow this to be spotted, although I suspect if at this stage of dying the trained ear ought probably to detect something amiss (? Theo / Rees ?) rather than it falling off mid session......

Unless I want to strip laquer as part of the clean I tend to use clean soft warm water an a drop of detergent with a rinse in clean warm water or sometimes meths, detergent does leave a film on metals. To strip laquqer I add a spot of caustic soda - don't use this on Aluminium that you want to keep a decent surface finish on.  Theo's warning on solvent use, particularly as the cleaning process both heats and may liberate some of the more volatile fractions of solvents even at room temperature should be noted.

The original blueing is an oxide coating from heat treatment and offers a degree of corrosion protection but not much, oiled or waxed gives a better result.
If the blue is 'essential' to you, it can be renewed by using a cold gun blue but this is nasty stuff and offers less protection in my experience than hot blueing even if oiled. I have to admit to using an alternative cold blueing method which you will not find in mainline use, I have a number of items with originally blued components in my 'museum', an unheated and partly below ground level shed ! and I have found that the most persistent blueing of components which are not regulalrly cleaned or polished is to use the blue equivalent of the humble black, waterproof magic marker pen, several thin applications with enough time for the previous one to dry off will leave a finish that is not easy to tell from hot blue.

I know that use of liquid corrosion barriers is not favoured due to the tacky surface which will pick up every bit of passing dust, however there are one or two which leave a thin dry coat which lasts for a very long while, the one I use on the brightwork of my steam engines is Shell Ensis liquid, several grades but the long life one if diluted with white spirit or paraffin will dry in about a week in a warm dry placeand if not abraded last almost indefinitely, can be removed with a wipe of the same solvent.

I will be trying this on my DG Pokerwork sometime, once I have persuaded the light rusting off the reeds and will let you know the result in 20 years time if I'm still about;)

Anyone else with a damp workshop etc, I keep a tobacco tin  of Ensis on a foam pad with some little foam bits that can be used as wipers, any tool which is used intermittently gets a quick wipe over with this after use and / or resharpening before being put away, the few seconds wiping it off next time make up for not having to de rust and resharpen the edge - put some in you used Febreze bottle for heavier applications - Solvent hazard warning applies to this as well ;)

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Presswood Pokerwork Rebuild
« Reply #42 on: December 19, 2010, 08:04:50 PM »

Richard,

I will pass this along to my clockmaker friend -- Thanks!

Bob
Logged

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: Presswood Pokerwork Rebuild
« Reply #43 on: December 19, 2010, 09:42:18 PM »

I use ultrasonic cleaning for the final cleaning of machined components for subsea and aerospace use.

You are not going to remove chemically attached corrosion,even with heavy duty units, alkaline cleaners and high temperatures.  Ultrasonic cleaning works by generating cavitation on the surface of the component to be cleaned - water is one of the best 'media'.

If you can find a processor, vapour degreasing is going to be a better option, finally using ultrasonic cleaning for the finish.

The industry standard dewatering oils (Rustilo, etc.) are going to be problematic - they attract dust and have limited life span.  Since you have to provide corrosion protection, consider phosphate dips -though how this will affect tuning,and how tuning will affect corrosion life, I shudder to think.
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Presswood Pokerwork Rebuild
« Reply #44 on: December 20, 2010, 05:48:46 PM »

I used to sneak my pushbike chain in to work and clean it in the ultrasonic bath.  I used a jar of parrafin in the water bath (like a bain-marie) and the chain came out shedding all the grit and grease.  As it was hot and dried quickly, I had to have a tin of chain lube ready melted to dunk it before it rusted!

I have used chemical bluing on a modified sump plug for a Ford prototype.  They forgot to leave room for it so we had to mill them down and refinish them.  Looks good, but I don't think the finish is particularly hardy on a car!  Should be OK inside a box, though, unless you drag it through the snow...

Rob.
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #45 on: December 27, 2010, 10:52:33 PM »

I've attached valves to the C row and started tuning. I'm raising the pitch of the instrument up to A=440 and am doing preliminary tuning of the reeds before waxing them onto the blocks. I've created a tuning box that allows me to have easy access to the tongue, flip the plate over to tune the other side and switch to the next plate. I've attached some photos below.

One puzzling thing. The push and pull reeds for buttons 6, 7, and 8 do not want to sound. I get a squeek, groan, high pitched overtone, flapping warble, but not a note, though I do hear air passing through the reed plate. The valves are well attached, do not rub against the side of the sounding chamber and open easily to allow air to pass. I tried different amounts of pressure, I adjusted the set of the reed tongue to a larger and smaller gap but there was no change in the ability of the reed to speak, no matter amount of pressure when pushing or pulling. I also checked that there was no fluff or other obstruction, passed a .002" feeler guage around the edges of the tongue and chamber and checked the tongue to make sure no parts were rubbing against the sides of the chamber. I also pulled a valve off one of the reeds to make sure there was no possible blockage to the air flow. Nothing helped. All of the lower reeds had sounded their notes just fine.

After puzzling over this for awhile and trying out various fixes, I pulled the "clamp" piece (see the second photo) off while the bellows was still falling/sucking, and the reed started to sound. For some reason the reed will speak when in an "open" system but not in a closed system. I tested the other "reluctant" reeds with this new setup and they all happily sounded! I don't know why.

Has anyone noticed this before? I haven't found anything in the archives about this but I may have missed something. I just don't know whether to wax the reeds into the reed block and hope that the reeds will sound in that situation.
« Last Edit: December 27, 2010, 11:32:43 PM by Telemorris »
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Presswood Pokerwork Rebuild
« Reply #46 on: December 27, 2010, 11:09:20 PM »

Third photo? - I can only see two... ???
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #47 on: December 27, 2010, 11:23:01 PM »

Third photo? - I can only see two... ???

For some reason the second one would not post. The photo I'm referencing is the second one. I'll edit that last post accordingly. Sorry for the confusion. Here's the "second" photo, I hope.
« Last Edit: December 27, 2010, 11:29:36 PM by Telemorris »
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

docEdock

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
  • Hohners, Gaillards, Castagnaris
    • LoafingAboard
Re: Presswood Pokerwork Rebuild
« Reply #48 on: December 30, 2010, 11:40:11 AM »

If I'm understanding your experiment, removing the "clamp" created a rectangular opening adjacent to the tip of the reed. Doing so during either a bellows push or pull caused the reed to vibrate in pitch. Yes? 

Humm, I'm hypothesizing that:

1) You were able to achieve a lower pressure with the clamp open than you could with even the most sensitive bellows work
or
2) The abrupt drop in the pressure gradient at the reed energized it to vibrate at a pitch (rather than a harmonic) in a way that a more gradual gradient created by moving the bellows did not.
or
3) The turbulence introduced by an opening near the tip of the read, energized it to vibrate in pitch.

To my mind, Occam's razor suggests 1 above, but your own experience may provide more evidence for 2 or 3. (Actually, I'm hoping that someone who really does knows about the fluid dynamics of semi-chaotic systems will read my speculations and -- with a groan and roll of the eyes -- explain what's really happening. I mean, really, all this jargon thrown around by an amateur -- like a red cape to a bull. Actually you started it when you mentioned "open system" and I remembered struggling through those physics lectures.)

Here's a question: if the opening were at the base of the reed would you get the same results?
Logged
How difficult can it be?
http://loafingaboard.blogspot.com/

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Presswood Pokerwork Rebuild
« Reply #49 on: December 30, 2010, 12:06:04 PM »

I get a squeek, groan, high pitched overtone, flapping warble, but not a note, though I do hear air passing through the reed plate.

These are usually symptoms of the reed tongue either being obstructed by a bit of airborne debris (sometimes too small to see with the naked eye) or the reed tongue coming into contact with the side of the vent.  The latter can be a result of the reed tongue being off centre, damage to the edge of the vent leaving a projecting burr, or occasionally the reed having the beginnings of a crack causing it to bend slightly sideways.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Presswood Pokerwork Rebuild
« Reply #50 on: December 30, 2010, 01:45:52 PM »

I notice that the beige coloured spring valve covering the white plastic valve is disproportionally long. Was that originally a longer valve that was shortened?
« Last Edit: December 30, 2010, 01:49:15 PM by diatonix »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Presswood Pokerwork Rebuild
« Reply #51 on: December 30, 2010, 01:55:05 PM »

The length of the with and beige parts looks normal.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Presswood Pokerwork Rebuild
« Reply #52 on: December 30, 2010, 02:50:10 PM »

Assuming that  it is a German M. Grimm valve, the beige part should be appr. 1/3 shorter in order to allow the white part to open satisfactorily. It looks wider than necessary, indicating again that it was probably meant to cover a larger reed. It's perfectly alright to adjust the length of plastic valves (within reason) as long as one remembers to cut the covering parts correspondingly. By not doing so, sound quality can suffer significantly.
« Last Edit: December 30, 2010, 06:13:14 PM by diatonix »
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #53 on: December 30, 2010, 06:42:36 PM »

Assuming that  it is a German M. Grimm valve, the beige part should be appr. 1/3 shorter in order to allow the white part to open satisfactorily. It looks wider than necessary, indicating again that it was probably meant to cover a larger reed. It's perfectly alright to adjust the length of plastic valves (within reason) as long as one remembers to cut the covering parts correspondingly. By not doing so, sound quality can suffer significantly.

The valves come from CGM. The white/beige valve is the smallest valve in the set. I'm not aware of the need to cut the upper piece of plastic. The kit comes with four sizes of valves, two and three part vinyl valves plus the plastic covered leather valves. Given what you're saying, most if not all should probably be adjusted in some way. Can you please explain the principles?

These are usually symptoms of the reed tongue either being obstructed by a bit of airborne debris (sometimes too small to see with the naked eye) or the reed tongue coming into contact with the side of the vent.  The latter can be a result of the reed tongue being off centre, damage to the edge of the vent leaving a projecting burr, or occasionally the reed having the beginnings of a crack causing it to bend slightly sideways.

Thanks Theo,

This set of reeds appears to be in fairly good shape. There's no rust to speak of and most of the reed plates are clean and the notes sound clearly. There's very little oxidation of the aluminum, unlike the zinc reeds in one of my other project boxes.

I've been using a set of feeler gages (.0025",.003", .004") to clean out the vent and edges of the reed tongue. I inspect the edges of the tongue and vent against a strong light, looking for any small breaks in the passage of light around the edge of the tongue and checking for an even amount of light to ensure the tongue is on center. Do you have any suggestions for cleaning out the vent and getting hidden particles out from under the tongue?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Presswood Pokerwork Rebuild
« Reply #54 on: December 30, 2010, 07:20:18 PM »

Bright light inspection is good.   Feeler gauges are not ideal, I prefer to use brass for getting under and around the reed tongue, because it is softer an less likely to damage the soft aluminium round the edge of the vent.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Presswood Pokerwork Rebuild
« Reply #55 on: December 30, 2010, 07:40:17 PM »

@telemorris: If these valves are the smallest in the set, and if they really are Grimm valves (but then, where else should they come from?) they have definitely been shortened after they left the factory. The smallest sizes (#11F 25mm, #12F 23mm have only white covers, #13F 22mm consists of only 1 layer), they cannot be neither #9For #10F because the beige part is too long (#9F:total length 28 mm, beige spring valve 12mm / #10F total length 27 mm, beige s.v. 11,5 mm). As a rule of thumb the length of the covering part in a 2piece valve should  be visibly less than half the total length.
I wouldn't be surprised if these valves could, in a way, account for some of the phenomenons you described earlier.
The letter F stands for "Folie" (plastic).
« Last Edit: December 30, 2010, 09:08:52 PM by diatonix »
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #56 on: December 30, 2010, 08:27:26 PM »

@telemorris: If these valves are the smallest in the set, and if they really are Grimm valves (but then, where else should they come from?) they have definitely been shortened after they left the factory.

I did cut the valve in the photo to length after the glue had dried. I'll cut the upper (beige) portion to half or less than half the length of the valve. Now I'm wondering about shortening the three piece valves. I've uploaded a photo of four reeds with the un-cut valves glued on. These are treble side reeds.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Presswood Pokerwork Rebuild
« Reply #57 on: December 30, 2010, 08:33:30 PM »

I would only have used the two right hand side size valves on the treble end, the others are to big. I would also have trimmed he overlapping bit (technical term) to be the same proportion as it was on the uncut valve - hopefully you understand that, if not I will try again  ;D

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Presswood Pokerwork Rebuild
« Reply #58 on: December 30, 2010, 08:43:11 PM »

Exactly, Lester. Of course, the correct valve for the correct reed would be preferrable, as the thickness of the plastic may vary. For the last  reeds on the block that require valves I'd go for a valve without cover.
« Last Edit: December 30, 2010, 08:48:48 PM by diatonix »
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #59 on: December 30, 2010, 09:17:08 PM »

I would only have used the two right hand side size valves on the treble end, the others are to big. I would also have trimmed he overlapping bit (technical term) to be the same proportion as it was on the uncut valve - hopefully you understand that, if not I will try again  ;D

Thanks Lester. Yes, your comments/instructions make sense. I could pull off the valves I've put on so far and match the valve length to the chamber length. Are you thinking I should not have used the large white leather valve then? I'll need to count the valve blanks I have and make sure I'll have enough valves in the correct sizes to do 84 reeds. I know there are a couple of extras for each size.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F
Pages: 1 2 [3] 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal