Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 [4]   Go Down

Author Topic: Presswood Pokerwork Rebuild  (Read 21174 times)

0 Members and 1 Guest are viewing this topic.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Presswood Pokerwork Rebuild
« Reply #60 on: December 30, 2010, 09:28:35 PM »

I would only have used the two right hand side size valves on the treble end, the others are to big. I would also have trimmed he overlapping bit (technical term) to be the same proportion as it was on the uncut valve - hopefully you understand that, if not I will try again  ;D

Thanks Lester. Yes, your comments/instructions make sense. I could pull off the valves I've put on so far and match the valve length to the chamber length. Are you thinking I should not have used the large white leather valve then? I'll need to count the valve blanks I have and make sure I'll have enough valves in the correct sizes to do 84 reeds. I know there are a couple of extras for each size.

I would only use the largest valves on the bass reeds

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #61 on: December 30, 2010, 09:35:24 PM »

CGM provides a separate group of reeds for the bass side. I'll see what I can do about changing the valves around to conform to more correct sizes and cut the valve layers to the same proportions as the full size valves. Thanks very much for this help.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Presswood Pokerwork Rebuild
« Reply #62 on: December 30, 2010, 09:41:41 PM »

To what length should the valves be positioned/cut? Just overlapping the cut-out, or rather more?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #63 on: December 30, 2010, 09:42:13 PM »

For the last  reeds on the block that require valves I'd go for a valve without cover.

The last two sets of plates/notes for each row did not have valves originally and the advice in the archives has been to refrain from putting valves on them. Oh, you're saying to remove the beige piece of plastic? I could cut it back to the place where the beige piece is glued on.

Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Presswood Pokerwork Rebuild
« Reply #64 on: December 30, 2010, 09:49:28 PM »

Yes, that's quite alright. I did that myself once, when I had run out of #13F.
I'd be interested in knowing whether your reeds with more suitable valves now behave as they should when being pre-tuned.
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #65 on: December 30, 2010, 09:52:38 PM »

To what length should the valves be positioned/cut? Just overlapping the cut-out, or rather more?

Good question. What might help is a photo of a reed plate with properly sized valve. The adjacent reed chamber is a good reference for how much overlap of the valve is appporiate.

Diatonix, I believe you mentioned you thought the valve in the original photo was too wide. What do all of you think is the correct width/overlap of a valve on the chamber? Is it necessary to cut a valve down in width as well as length?



Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Presswood Pokerwork Rebuild
« Reply #66 on: December 30, 2010, 10:17:39 PM »

When dealing with plastic valves, the overlap can be minimal, say 0.5mm. Leather and combi valves: about 1 mm, allowing for possible shrinking. Too much glue is another frequent error, about a square (the width of the valve being its sides) is enough, maybe a little less when dealing with smaller valves, a little more with larger valves.
I wouldn't deem it wise to cut your valves down in width as well. Possible damage is likely to occur and you don't seem to have too many spares.
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #67 on: December 30, 2010, 10:38:19 PM »

Yes, that's quite alright. I did that myself once, when I had run out of #13F.
I'd be interested in knowing whether your reeds with more suitable valves now behave as they should when being pre-tuned.

I'm working from home today and ran down to the shop briefly to try this out. The valves do not make any difference in the sounding of the reeds. I'm going to pull the valves off again since they block the light for visual inspection of the reed and chamber opening.

I'll have to pick up some brass shim stock for cleaning up the chambers and reed edges. Thanks for that tip Theo.

One of the problems with this set of reeds is that the instrument they were in was stored in a damp environment. The reed tongues had moderate to heavy rust which I've cleaned off with very fine sandpaper. However, the zinc reed plates, have a fine white coat of oxide in different places and some small burrs of oxide formed inside the reed chambers in some of the plates, hence my working with feeler gages to try to smooth things out.

It just occurred to me that the rust on the top and bottom of the tongue may also have attacked the edges of the tongues and be causing some of the problems with obstruction, though I don't see any roughness there. Can I very lightly sand the tongue edges with, say, 1200 grit paper? If not, what do I use to clean up the edges of the tongue and the chamber?

Thanks!
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #68 on: January 17, 2011, 05:44:32 PM »

My progress so far...

I spent the weekend working on the bellows repair. All of the long side papers have been replaced. I found a very nice green paper and used a yellow PVA, Elmers Wood Glue, to glue the papers down. My process was the same as Theo suggested for gluing bellows tape: brush a layer of glue onto a non-absorbent surface, a plastic sheet in my case, put the papers onto the glue "sheet" then put in place. The new papers look fairly good for a first attempt at doing this kind of repair.

Things learned... Use a stiffer, harder type of paper, perhaps something closer to printer paper. The green paper turned out to have two layers though I didn't know that until I started trying to pull it off the glue on the plastic sheet. The paper is certainly thin enough but the under layer would sometimes separate once wet with the glue. Also, the paper would expand a bit from absorbing the water in the glue. As a result the cut ends of the papers that were accurately cut to the length of the tapes came out a bit longer than planned - two or three mm.

I also started gluing on bellows tapes and found the process difficult to control. I'm using the vinyl impregnated(?) 3/4 inch wide tape that Charley Marshall sells. I used the same process that Theo recommends for applying glue, same as above. The tape refused to fold around the edge of the bellows fold and stay in place while trying to apply the next piece. I did use some clothes pins to hold the ends in place, (thanks for that idea Lester). I don't know whether the problem was too little glue, not enough open time to allow the glue to tack up, or that I'm using the wrong kind of glue. I did try some paste that I have "Yes" paste that has proved wonderful for other jobs on the melodeon. If I let the glue dry for a bit before trying to stick the tape down I'd sometimes end up with the glue drying out too much with the result that the tape would not stick at all.

I'm hoping someone can post some of the finer details of gluing up and applying bellows tape. I've found most, if not all, of the descriptions of applying bellows paper and tapes in the archives. I'm hoping that some of these experiences can be helpful to someone else trying to repair their bellows for the first time. This is all a learning process and I'm having fun working on my Presswood Pokerwork.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Presswood Pokerwork Rebuild
« Reply #69 on: January 17, 2011, 05:55:41 PM »

Hmm, that doesn't sound pleasant. I have a horrible feeling that the papers as well as the tape on my Imperial need replacing, which would increase the work significantly and your experience meets up to my expectations :P
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Presswood Pokerwork Rebuild
« Reply #70 on: January 17, 2011, 06:18:16 PM »

Up until recently I have used Charlie Marshall's "special" paste which is a bit of a pain to apply to the tape, so for the last go I used Polyten PVA Glue which has a fast 10 minute tack time and is much easier to handle. I just blobbed some on the tape and spread it out with a brush, not too much and not too little (you will soon find out how much). Then just place the tape and it will grab quite easily. After doing  all of one side I still clamp the bellows up with greaseproof between the folds for a couple of hours.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #71 on: January 17, 2011, 06:52:14 PM »

I did clamp the tape overnight to ensure a good bond. For clamping I've been using waxed paper to prevent stray bits of glue from sticking the folds together. I fold a piece of wax paper in half such that the doubled piece sticks above the bellows fold. Then I insert a piece of cereal box cardboard between the wax paper. The cardboard is cut to the length of the bellows fold such that it stops just inside the metal corner pieces. The cardboard is also only as wide as the distance from the bottom (valley) of the leather gusset fold to the bottom edge of the metal corner piece.

I've used these cardboard pieces to help apply pressure to the surface of the paper and tape because the metal corners plus bellows tape stands proud of the surface of the bellows card and prevents any real pressure on the glued up surface of the bellows tape. This assembly works quite well.

Thanks for the glue idea. I'll have to look for some here in the US (I still haven't found a source for the cleaning block that you from Maplins). It sounds like the main issue is the tack time and the strength of the tack.

Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #72 on: January 17, 2011, 07:04:49 PM »

Hmm, that doesn't sound pleasant. I have a horrible feeling that the papers as well as the tape on my Imperial need replacing, which would increase the work significantly and your experience meets up to my expectations :P

Ukebert, don't let the work intimidate you. I'm in the beginning stages if figuring out how to do these repairs. That's why I glue up a few tapes then evaluate the process to try and get the bugs out. Starting with a side that isn't seen when playing also helps to hide any screwups too. I don't expect this first repair to look perfect though I always hope for the best. I do expect to end up with airtight bellows though. I'm also working on an inexpensive instrument that I have the courage to deal with. I would not attempt any of this work on an expensive instrument. I'll also keep trying until I get something that looks right even if it means building new bellows myself, a personal preference since I love to do this kind of work. By the time I get to building a new bellows, I'll have learned how to do these steps.

The only way I can learn how to do this is try, evaluate, try again. Theo and some others on this forum learned by trial and error.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Presswood Pokerwork Rebuild
« Reply #73 on: January 17, 2011, 07:10:49 PM »

Wise words Telemorris. My method with this kind of thing is to spend huge quantities of time looking up exactly what to do in every case, then when I start to do it I can much more easily work out what to do completely differently from what I'm "supposed" to :P Trial and error is regrettably necessary though, regrettable because I immediately form an emotional attachment to any instrument, and whilst it is supremely satisfying to work on them, I would be very upset if I was to irrevocably ruin them. Tuning and bellows repair are the two things that I am concerned about; for the former I have a box which the reeds aren't amazing anyway, for the latter (which is potentially more of a problem if it goes horrifically wrong) I have a Piano Accordion >:E
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #74 on: January 17, 2011, 08:22:25 PM »

For me, tuning is the stickier issue since reeds are the sound source and modifying the tongue changes not only the pitch, it changes the harmonics and many other aspects of the sound of an instrument. Small modifications can have huge consequences. Even in an older instrument that might be inexpensive, the reeds might be valuable precisely because they're not made anymore or have a particularly sought after sound. A good case in point is the "junker" that I bought thinking I could use it for learning to tune. When I opened it up I found Hohner H reeds on zinc plates. I've got to be very careful with those reeds.

The bellows are paper and leather and more easily repaired or replaced, within reason. In an older, less valuable instrument, I can experiment and learn. I really would not touch a more expensive instrument because I don't know what I'm doing - yet. After I've done a few of these, I'll have acquired the beginnings of a sense of the process and built up a starting skill set that gives me a certain sense of confidence in how to tackle the basic repairs. Every instrument is different and the repairs are going to be different.

I dare say that Theo, Rees, and the others who are professionals, with all their years of experience, still find themselves with repair tasks that have not come up before and they must, therefore, feel their way carefully to a solution. It's the years of experience with many different repairs that gives a clue as to how to proceed with something new.

I've grown ponderous. Sorry.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Presswood Pokerwork Rebuild
« Reply #75 on: January 17, 2011, 11:07:35 PM »

I dare say that Theo, Rees, and the others who are professionals, with all their years of experience, still find themselves with repair tasks that have not come up before

Most of what I've learned I have learned from my mistakes :|bl - and I'm still learning. :|bl
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: 1 2 3 [4]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal