Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3 4   Go Down

Author Topic: Presswood Pokerwork Rebuild  (Read 21172 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Presswood Pokerwork Rebuild
« on: December 09, 2010, 05:22:31 PM »

I thought I'd create one thread for repair questions to do with my Presswood Pokerwork rather than start many small threads.

First obstacle I ran into last night was in trying to remove the Bass mechanism for cleaning and replacing the felt washers under the buttons (picture below). I thought I should remove the buttons in order to remove the mechanism but I can't figure out how to get the buttons off. Is there heat involved? I've looked in the archives and haven't found anything about removing the buttons. I'm probably not searching using the exact correct terms. Any suggestions?

Thanks,

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Presswood Pokerwork Rebuild
« Reply #1 on: December 09, 2010, 05:28:47 PM »

My personal preference is to undo the nail hinge where the button rods meet the mechanism, again my preference is to ship the heads off the nails and replace them. It is v important that you mark the rods in some way to get them back in the position they start in as they are all subtlety different.

The buttons are just an interference fit but are hard to remove and I am not sure, never having done it, how well they will stay in place if removed and replaced.

I know Theo's preference (judging from a previous thread) is to remove the buttons and so it must be possible and probably sensible, I guess he will be along soon.

ps, your bass mechanism looks to be badly bent out of shape for the rods to be sticking out that far if they are still connected?

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #2 on: December 09, 2010, 05:51:10 PM »

Thanks Lester. I looked at the bent nail hinge and thought I'd rather not touch that. At least that was my first impression when confronted with this puzzle. I'll have to try that tonight unless Theo can advise how to remove the buttons. I'd like to extract the entire mechanism for cleaning, another reason for removing the buttons.

Have you ever enlarged the holes and bushed the holes with felt? It seems like a nice upgrade.

I'd already removed the screws from the mechanism and the rods were pushed up as a result when I took that photo. Not to worry. When the mechanism is screwed in, the buttons sit at a normal height and register inside the holes the way they are supposed to. I took photos of the instrument to document the starting condition and will post them on Picasa later.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Presswood Pokerwork Rebuild
« Reply #3 on: December 09, 2010, 06:00:06 PM »

Have you ever enlarged the holes and bushed the holes with felt? It seems like a nice upgrade.
I'm about to do that on a Hohner Erica. Lester has kindly supplied me with replacement nails for the rod pivots (which I need to dismantle to get access to the button holes), and I have bought some proper concertina bushing felt from David Leese in North Wales which I hope will be just the job. Will report back as and when I progress with the work.

http://www.concertina-spares.com
http://www.concertina-spares.com/catalogue11.htm

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Presswood Pokerwork Rebuild
« Reply #4 on: December 09, 2010, 06:07:22 PM »


I'm about to do that on a Hohner Erica. Lester has kindly supplied me with replacement nails for the rod pivots (which I need to dismantle to get access to the button holes), and I have bought some proper concertina bushing felt from David Leese in North Wales which I hope will be just the job. Will report back as and when I progress with


Photos please as it is on my list for my super-Erica I'm building.

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Presswood Pokerwork Rebuild
« Reply #5 on: December 09, 2010, 06:55:35 PM »

If the existing buttons are sound, cut/straighten the pins and remove the rods!
The buttons are interference fit and may not take kindly to being levered off.
New replacements are easy to come by, but inferior finish.
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #6 on: December 09, 2010, 07:34:56 PM »

Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Presswood Pokerwork Rebuild
« Reply #7 on: December 09, 2010, 07:43:25 PM »

Here are my photos of the instrument before repairs.

http://picasaweb.google.com/TeleMorris/PresswoodPokerwork?authkey=Gv1sRgCLuXpqru26SMfg#

I would recommend disconnecting the springs before either unscrewing or replacing the mechanism as they place a lot of strain on the very small brass screws until the mechanism is screwed down with all the screws.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #8 on: December 09, 2010, 07:55:37 PM »

I would recommend disconnecting the springs before either unscrewing or replacing the mechanism as they place a lot of strain on the very small brass screws until the mechanism is screwed down with all the screws.

While I didn't think of that before removing the screws to take off the mechanism, I did disconnect the springs to put the mechanism back later. It's a good safety measure. Thanks Lester.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Presswood Pokerwork Rebuild
« Reply #9 on: December 09, 2010, 09:13:53 PM »


I'm about to do that on a Hohner Erica. Lester has kindly supplied me with replacement nails for the rod pivots (which I need to dismantle to get access to the button holes), and I have bought some proper concertina bushing felt from David Leese in North Wales which I hope will be just the job. Will report back as and when I progress with


Photos please as it is on my list for my super-Erica I'm building.
Right-oh. It may take me a while to get going with it though, at this time of year.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Presswood Pokerwork Rebuild
« Reply #10 on: December 09, 2010, 11:51:34 PM »

Right-oh. It may take me a while to get going with it though, at this time of year.

That's good for me, the reeds for super-Erica are coming from Father Christmas so no great hurry (:)

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #11 on: December 10, 2010, 12:08:33 AM »

Lester, would you mind explaining "Super Erica",  please? I'm really curious now.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Presswood Pokerwork Rebuild
« Reply #12 on: December 10, 2010, 12:43:44 AM »

Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink
Bob
« Last Edit: December 10, 2010, 02:42:27 AM by RGF »
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Presswood Pokerwork Rebuild
« Reply #13 on: December 10, 2010, 01:14:37 AM »

Telemorris, I use heat to remove the bass buttons. Use a soldering iron to heat the rod as close as possible to the underside of the button. As a rule of thumb, as soon as you catch a whiff of melting plastic, withdraw the heat and gently ease the button off.

However, I'm sure the said "whiff of melting plastic" is possibly dangerous to health and probably carcenagenic, maybe even haluciagenic, so I accept no responsibility.... etc. etc.

But hey, life's a risk.... >:E



Logged
Tuner/repairer, now retired.

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Presswood Pokerwork Rebuild
« Reply #14 on: December 10, 2010, 04:11:27 AM »

Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink
Bob

Nice work.  The heat shrink tubing on the wooden dowel is brilliant.
Logged

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Presswood Pokerwork Rebuild
« Reply #15 on: December 10, 2010, 08:33:56 AM »

Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink
Bob
Nice work.  I need to re-visit the bass on my Pokerwork.
Logged
Tony S

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Presswood Pokerwork Rebuild
« Reply #16 on: December 10, 2010, 09:02:43 AM »

Lester, would you mind explaining "Super Erica",  please? I'm really curious now.

I have purchased an Erica body, old style - flat grille, wooden keyboard, and am getting a set of Cagoni italian  reeds from Father Christmas. It will probably be 4th button start and I will tune it drier than my Hohners , thus giving me a lightweight, hopefully Italian sounding, box rather than lugging one of my Salterelles around. This is my project for the New Year.

All will be revealed  (:)

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Presswood Pokerwork Rebuild
« Reply #17 on: December 10, 2010, 04:14:07 PM »

Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink
Bob

Wow, Bob! Really lovely work.

Interested by the ultrasonic cleaner. Is this one that uses water as a solvent? Does it work well?
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Presswood Pokerwork Rebuild
« Reply #18 on: December 10, 2010, 04:42:16 PM »

Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink
Bob
That's really nice work. What a great sequence of photos.
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Presswood Pokerwork Rebuild
« Reply #19 on: December 10, 2010, 04:43:47 PM »


snip

Interested by the ultrasonic cleaner. Is this one that uses water as a solvent? Does it work well?

I'm very interested in the ultrasonic cleaner too. How does it work for rust?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F
Pages: [1] 2 3 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal